maintenance NISSAN PULSAR 2021 Owner´s Manual

Page 172 of 217



> (GLW   0RGHO &$@
Tires*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thepressure withagauge oftenandalways
prior tolong distance trips.Adjust thepressure inall
tires, including thespare, tothe pressure specified.
Check carefully fordamage, cutsorexcessive wear.
Tire rotation*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
In the case thatTwo-Wheel Drive(2WD) andfront &
rear tires aresame size;Tires should berotated every
10,000 km(6,000 miles).Tires marked withdirectional
indicators canonly berotated between frontandrear.
Make surethatthedirectional indicatorspointinthe
direction ofwheel rotation afterthetire rotation is
completed.
In the case thatFour-Wheel Drive(4WD) andfront &
rear tires aresame size;Tires should berotated every
5,000 km(3,000 miles).Tires marked withdirectional
indicators canonly berotated between frontandrear.
Make surethatthedirectional indicatorspointinthe
direction ofwheel rotation afterthetire rotation is
completed.
In the case thatfront tiresaredifferent sizefrom rear
tires; Tirescannot berotated.
However, thetiming fortire rotation mayvaryaccording
to your driving habitsandtheroad surface conditions.
Tire Pressure Monitoring System(TPMS)trans-
mitter components (ifequipped) :
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Replace theTPMS transmitter grommetseal,valve
core andcap when thetires arereplaced duetowear
or age.
Wheel alignment andbalance:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
If the vehicle shouldpulltoeither sidewhile driving on
a straight andlevel road, orifyou detect uneven or
abnormal tirewear, theremaybeaneed forwheel
alignment. Ifthe steering wheelorseat vibrates at
normal highway speeds,wheelbalancing maybe needed.
Windshield:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Clean thewindshield onaregular basis.Check the
windshield atleast every sixmonths forcracks orother
damage. Repairasnecessary .
Wiper blades*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check forcracks orwear ifnot functioning correctly.
Inside vehicle
GUID-55 4469D2-12 96-4F49-B7A0 -0A8847FB7455
The maintenance itemslistedhereshould bechecked
on aregular basis,suchaswhen performing periodic
maintenance, cleaningthevehicle, etc.
Accelerator pedal:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thepedal forsmooth operation andmake sure
that thepedal doesnotcatch orrequire uneven effort.
K eep thefloor mats away fromthepedal.
Brake pedal*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thepedal forsmooth operation andmake sure
that itis the proper distance fromthefloor matwhen
depressed fully.Check thebrake booster function. Be
sure tokeep thefloor mats away fromthepedal.
Parking brake*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check theparking brakeoperation regularly.Check
that thelever (ifequipped) orthe pedal (ifequipped)
has theproper travel.Alsomake surethatthevehicle is
held securely onafairly steep hillwhen onlythe
parking brakeisapplied.
Seat belts:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thatallparts ofthe seat beltsystem (for
example, buckles,anchors, adjusters andretractors)
operate properly andsmoothly ,and areinstalled
securely .Check thebelt webbing forcuts, fraying,
wear ordamage. Steering
wheel:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check forchanges inthe steering condition, suchas
excessive play,hard steering orstrange noises.
Warning lightsandchimes:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Make surethatallwarning lightsandchimes are
operating properly.
Windshield defogger:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thattheaircomes outofthe defogger outlets
properly andingood quantity whenoperating the
heater orair conditioner.
Windshield wiperandwasher*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thatthewipers andwasher operate properly
and that thewipers donot streak.
Under hoodandvehicle
GUID-E5D 10961-EA14 -4A37-B87E- 268783A0FC3 8
The maintenance itemslistedhereshould bechecked
periodically (forexample, eachtimeyoucheck the
engine oilorrefuel) .
Battery*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Except formaintenance freebattery ,check thefluid
level ineach cell.Itshould bebetween theªUPPERº
and ªLOWERº lines.Vehicles operated inhigh
temperatures orunder severe conditions require
frequent checksofthe battery fluidlevel.
Brake (andclutch) fluidlevel(s)*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
For Manual Transmission (MT)model; makesurethat
the brake andclutch fluidlevels arebetween the
ªMAXº andªMINº linesonthe reservoirs.
Except forManual Transmission (MT)model; make
sure thatthebrake fluidlevel isbetween theªMAXº
and ªMINº linesonthe reservoir.
Maintenan ceand do-it-you rself
8-3
&RQGLWLRQ

Page 173 of 217



> (GLW   0RGHO &$@
8-4
Mainten anceanddo-it-yo urself
Coolant level*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thecoolant levelwhen thecoolant iscold. Make
sure thatthecoolant levelisbetween theªMAXº and
ªMINº linesonthe reservoir.
Engine drivebelt(s)*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Make surethatdrive belt(s) is/arenotfrayed, worn,
cracked oroily .
Engine oillevel*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thelevel afterparking thevehicle (onalevel
ground) andturning offthe engine.
Fluid leaks:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check underthevehicle forfuel, oil,water orother fluid
leaks afterthevehicle hasbeen parked forawhile.
W ater dripping fromtheairconditioner afteruseis
normal. Ifyou should noticeanyleaks oriffuel fumes
are evident, checkforcause andhave itcorrected
immediately .
Windshield washerfluid*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thatthere isadequate fluidinthe reservoir.
MAINTENANCE PRECAUTIONS
GUID-E46 9E0D9-6CF F-4A9B-8459-D2B589DFA455
When performing anyinspection ormaintenance work
on your vehicle, alwaystakecare toprevent serious
accidental injurytoyourself ordamage tothe vehicle.
The following aregeneral precautions whichshould be
closely observed.
WARNING:
. Park thevehicle onalevel surface, applythe
parking brakesecurely andblock thewheels
to prevent thevehicle frommoving. Move
the shift lever tothe ªPº(Park) position (CVT
model) orthe shift lever tothe ªNº(Neutral)
position (MTmodel) . .
Besure theignition switchisin the ªOFFº or
ªLOCKº position whenperforming anyparts
replacement orrepairs.
. Do not work under thehood while the
engine ishot. Always turnoffthe engine
and wait until itcools down.
. Ifyou must workwiththeengine running,
keep yourhands, clothing, hairandtools
away frommoving fans,belts andanyother
moving parts.
. Itis advisable tosecure orremove anyloose
clothing andanyjewelry, suchasrings,
watches, etc.before working onyour vehi-
cle.
. Ifyou must runtheengine inan enclosed
space suchasagarage, besure there is
proper ventilation forexhaust gasesto
escape.
. Never getunder thevehicle whileitis
supported byajack.
. Keep smoking materials, flameandsparks
away fromfuelandthebattery.
. Never connect ordisconnect eitherthe
battery orany transistorized component
connector whiletheignition switchisin the
ªONº position.
. Ongasoline enginemodels withtheMulti-
port Fuel Injection (MFI)system, thefuel
filter andfuel lines should beserviced bya
NISSAN dealerbecause thefuel lines are
under highpressure evenwhen theengine is
turned off.
. Your vehicle isequipped withanautomatic
engine cooling fan.Itmay come onatany
time without warning, evenifthe ignition switch
isin the ªOFFº position andthe
engine isnot running. To avoid injury, always
disconnect thenegative batterycablebefore
working nearthefan.
. Always weareyeprotection wheneveryou
work onyour vehicle.
. Never leavetheengine ortransmission
related component harnessconnector dis-
connected whiletheignition switchisin the
ªONº position.
. Avoid directcontact withused engine oiland
coolant. Improperly disposedengineoil,
engine coolant, and/orothervehicle fluids
can hurt theenvironment. Alwaysconform to
local regulations fordisposal ofvehicle
fluids.
This ª8.Maintenance anddo-it-yourselfº section
provides instructions regardingonlythose itemswhich
are relatively easyforanowner toperform.
Y ou should beaware thatincomplete orimproper
servicing mayresult inoperating difficulties orex-
cessive emissions, andcould affect yourwarranty
coverage. Ifin doubt aboutanyservicing, haveit
done byaNISSAN dealer.
&RQGLWLRQ

Page 178 of 217



> (GLW   0RGHO &$@
GUID-B1 20ADA3-D0 3C-49B1-B529-7A274B D909D0
CHECKING ENGINEOILLEVEL
GUID-7F B3D707-0 60C-4B57-B BE7-3BDD80ACE30 5
SDI1993
T ype A
SDI2721
T ype B
1. Park thevehicle onalevel surface andapply the
parking brake.
2. Start theengine andwarm itup until theengine
temperature reachesthenormal operating tem-
perature (approximately 5minutes) .
3. Stop theengine.
4. Wait atleast 10minutes forthe engine oiltodrain
back tothe oilpan.
5. Remove thedipstick andwipe itclean. 6.
Reinsert thedipstick allthe way.
7. Remove thedipstick andcheck theoillevel. It
should bewithin therange
*
C
.
8. Ifthe oillevel isbelow
*
A
, remove theoilfiller cap
and pour therecommended oilinto theopening.
Do not overfill
*
B
.
When fillingtheengine oil,donot remove
the dipstick.
9. Recheck theoillevel withthedipstick.
It is normal toadd some oilbetween oil
maintenance intervalsorduring thebreak -in
period, depending onthe severity ofoperat-
ing conditions.
CAUTION:
The oillevel should bechecked regularly.
Operating yourvehicle withaninsufficient
amount ofoil can damage theengine, andsuch
damage isnot covered bythe warranty.
CHANGING ENGINEOILAND OILFILTER
GUID-BFC63 F3B-A179-42CF-BDF1-B 43386889AD1
WARNING:
. Used oilmust bedisposed ofproperly. Never
pour ordump oilinto theground, canals,
rivers, etc.It should bedisposed ofatproper
waste facilities. NISSANrecommends hav-
ing your oilchanged byaNISSAN dealer.
. Be careful nottoburn yourself, asthe
engine oilmay behot.
. Prolonged andrepeated contactwithused
engine oilmay cause skincancer.
. Avoid directskincontact withused oil.If
contacted, washthoroughly withsoap or hand
cleaner andplenty ofwater assoon as
possible.
. Store usedengine oilinmarked containers
out ofthe reach ofchildren.
1. Park thevehicle onalevel surface andapply the
parking brake.
2. Start theengine andwarm itup until theengine
temperature reachesthenormal operating tem-
perature (approximately 5minutes) .
3. Stop theengine.
4. Wait atleast 10minutes forthe engine oiltodrain
back tothe oilpan.
5. Raise andsupport thevehicle usingasuitable
floor jackandsafety jackstands.
.
Place thesafety jackstands underthevehicle
jack -up points.
.
A suitable adaptershouldbeattached tothe
jack stand saddle.
6. For HR16DE enginemodel,remove theplastic
engine undercover.
.
Remove thebolts andplastic clipsfromthe
undercover.
Maintenan ceand do-it-you rself
8-9
ENGINE
OIL
&RQGLWLRQ

Page 179 of 217



> (GLW   0RGHO &$@
8-10
Maintenance anddo-it-yours elf
Engine oiland filter
GUID-5F 013F78-E E34-4C18-B FFB-79938 408A1A2
JVM0161X
MRA8DE engine model
SDI2652
MR16DDT engine model
JVM0081X
MRA8DE andMR16DDT engine model
SDI2722
HR16DE enginemodel
*
1
Oil filler cap
*
2
Oil drain plug
*
3
Oil filter
1. Place alarge drainpanunder thedrain plug.
2. Remove thedrain plugwithawrench.
3. Remove theoilfiller capand completely drainthe
oil.
If the oilfilter isto be changed, removeand
replace itat this time.
CAUTION:
Waste oilmust bedisposed ofproperly. Check
your local regulations.
4. Loosen theoilfilter withanoilfilter wrench.
5. Remove theoilfilter byturning itby hand.
6. Wipe theengine oilfilter mounting surfacewitha
clean cloth.
Be sure toremove anyoldgasket remaining onthe
mounting surface.
7. Apply newengine oiltothe gasket ofthe new oil
filter.
8. Screw inthe oilfilter untilaslight resistance isfelt
and then tighten anadditional 2/3ofaturn to
secure thefilter.
Oil filter tightening torque:
15 to20 N´m
(1.5 to2.0 kg-m, 11to15 ft-lb)
9. Clean andreinstall thedrain plugandnew washer.
Securely tightenthedrain plugwithawrench. Do
not use excessive force.
Drain plugtightening torque:
29 to39 N´m
(3.0 to4.0 kg-m, 22to29 ft-lb)
10. Refill therecommended engineoiland quantity .
(See ªRecommended fluids/lubricantsandcapa-
citiesº (P.9-2) .)
When fillingtheengine oil,donot remove
the dipstick (exceptforHR16DE engine
model) .
11. Securely installtheoilfiller cap.
&RQGLWLRQ

Page 180 of 217



> (GLW   0RGHO &$@
12. Start theengine.
13. Check thedrain plugforany sign ofleakage.
14. Dispose ofthe used oilinthe proper manner.
Check yourlocal regulations.
15. Check theengine oillevel according tothe proper
procedure. (SeeªChecking engineoillevelº (P.8-
9) .)
After theoperation
GUID-D31 C7ECF-FDA1 -4CF1-B6A7-3C0771BAD AF0
1. For HR16DE enginemodel,installtheengine
undercover intoposition asthe following steps.
a. Pull thecenter ofthe small plastic clipout.
b. Hold theengine undercover intoposition.
c. Insert theclip through theundercover intothe
hole inthe frame, thenpush thecenter ofthe
clip into lock theclip inplace.
d. Install theother boltsthathold theundercover
in place. Becareful nottostrip thebolts or
over-tighten them.
2. Lower thevehicle carefully tothe ground.
3. Dispose ofwaste oiland filter properly .
GUID-4B 37DD34-9 FBB-48DA-870 F-42F8858 0E4D7
SDI1881
MRA8DE andMR16DDT enginemodel
1. Alternator
2. Drive beltauto-tensioner
3. Crankshaft pulley
4. Airconditioner compressor
5. Water
pump
SDI1862
HR16DE enginemodel
1. Water pump
2. Alternator
3. Crankshaft pulley
4. Airconditioner compressor
!: Tension checking point
Be sure theignition switchisin the ªOFFº position. Visually
inspectthebelt forsigns ofunusual wear,cuts,
fraying orlooseness. Regularlycheckthecondition
and tension (forHR16DE enginemodel).If the belt is
in poor condition orloose, haveitreplaced oradjusted
by aNISSAN dealer.
Maintenance anddo-it-yours elf
8-11
DRIVE
BELT
&RQGLWLRQ

Page 181 of 217



> (GLW   0RGHO &$@
8-12
Maintenance anddo-it-yours elf
GUID-5EDAE 568-00C3-4A3B-9C28-6044BCDA9 F5A
WARNING:
Be sure theengine andignition switchareoff
and that theparking brakeisapplied.
Replace thespark plugs according tothe maintenance
log shown inaseparate maintenance booklet.
If replacement isrequired, contactaNISSAN
dealer.
SDI2670
IRIDIUM PLATINUM- TIPPED SPARK PLUGS
(if equipped)
GUID-41 0FE3E4-44 1B-4391-8865-CAF43CB 9DCEE
It is not necessary toreplace theiridium platinum-
tipped sparkplugs asfrequently asthe conventional
type ofspark plugs. These sparkplugs aredesigned to
last much longer thantheconventional typeofspark
plugs.
CAUTION:
. Do not reuse theiridium platinum-tipped
spark plugsbycleaning orre-gapping.
. Always replace withtherecommended ir-
idium platinum-tipped sparkplugs.
PLA TINUM ALLOY-TIPPED SPARK PLUGS
(if equipped)
GUID-8A4B 4C64-A675-4D67-A626-E073893D D58D
It is not necessary toreplace theplatinum alloy-tipped
spark plugs asfrequently asthe conventional typeof
spark plugs. These sparkplugs aredesigned tolast
much longer thantheconventional typeofspark plugs.
CAUTION:
. Donot reuse theplatinum alloy-tipped spark
plugs bycleaning orre-gapping.
. Always replace withtherecommended pla-
tinum alloy-tipped sparkplugs.
GUID-F4973 34F-4BCC-4 81C-99C2-53B8238FFDF5
CHECKING PARKING BRAKE
GUID-7CB 565C4-046 3-4945-B007-47D7F7E6 B757
SDI1447A
From thereleased position,pulltheparking brakelever
up slowly andfirmly .If the number ofclicks isout ofthe
range listed, seeaNISSAN dealer.
Pulling force
196 N(20 kg,44lb)
Rear discbrake models:
9 to 10 clicks
Rear drum brake models:
8 to 9clicks
CHECKING FOOTBRAKE PEDAL
GUID-0E50 006C-EEFA-471F-80 2B-36E5E9 5578F4
DI1020MR
SP ARK PLUGS BRAKES
&RQGLWLRQ

Page 182 of 217



> (GLW   0RGHO &$@
WARNING:
See aNISSAN dealerforabrake system checkif
the foot brake pedalheight doesnotreturn to
normal.
With theengine running, checkthedistance
*
A
between theupper surface ofthe pedal andthemetal
floor. Ifitis out therange listed, seeaNISSAN dealer.
*
A
: Depressing force
490 N(50 kg,110 lb)
Rear drum brake models:
Ð 75 mm (2.95 in)ormore (LHDmodels)
Rear discbrake models:
Ð 70 mm (2.76 in)ormore (LHDmodels)
Ð 85 mm (3.35 in)ormore (RHD models)
Self-adjusting brakes
GUID-E13 91AD9-018D -40D0-9FCB-F7BFE6269D 65
Y our vehicle isequipped withself-adjusting brakes.
The disc-type brakesself-adjust everytimethefoot
brake pedalisapplied.
Brake padwear warning
GUID-0AD9 F709-9ABC -45A7-8A9A-B EC9A3A9E863
The disc brake padshaveaudible wearwarnings.
When abrake padrequires replacement, itwill make a
high pitched scraping soundwhenthevehicle isin
motion. Thisscraping soundwillfirst occur onlywhen
the brake pedalisdepressed. Aftermore wearofthe
brake pad,thesound willalways beheard evenifthe
brake pedal isnot depressed. Havethebrakes
checked assoon aspossible ifthe wear warning
sound isheard.
Under somedriving orclimate conditions, occasional
brake squeaks, squealsorother noises maybeheard.
Occasional brakenoiseduring lighttomoderate stops
is normal anddoes notaffect thefunction orperformance
ofthe brake system.
Proper brakeinspection intervalsshouldbefollowed.
For additional information, seeaseparate maintenance
booklet.
BRAKE BOOSTER
GUID-79 F46EFD-F4 7C-47DD-98FB -536B7D3C7D06
Check thebrake booster function asfollows:
1. With theengine off,depress andrelease thefoot
brake pedalseveral times.When thebrake pedal
movement (distanceoftravel) remains thesame
from onepedal application tothe next, continue on
to the next step.
2. While depressing thefoot brake pedal, startthe
engine. Thepedal height should dropalittle.
3. With thefoot brake pedaldepressed, stopthe
engine. Keep thepedal depressed forabout 30
seconds. Thepedal height should notchange.
4. Run theengine for1minute without depressing
the foot brake pedal, thenturnitoff. Depress the
foot brake pedalseveral times.Thepedal travel
distance willdecrease graduallywitheach de-
pression asthe vacuum isreleased fromthe
booster.
If the brakes donot operate properly,have thebrakes
checked byaNISSAN dealer.
GUID-7B48C 533-E5D3-486B-BF9A-FB 22BA267E0A
WARNING:
. Use only newfluid from asealed container.
Old, inferior, orcontaminated fluidmay
damage thebrake system. Theuseof
improper fluidscandamage thebrake
system andaffect thevehicle's stopping
ability.
. Clean thefiller capbefore removing.
. Brake fluidispoisonous andshould be
stored carefully inmarked containers out
of the reach ofchildren.
CAUTION:
Do not spill thefluid onpainted surfaces. This
will damage thepaint. Iffluid isspilled, washit
off with plenty ofwater
immediately.
SDI2688
Left-Hand Drive(LHD) models
Maintenance anddo-it-yours elf
8-13
BRAKE
FLUID
&RQGLWLRQ

Page 183 of 217



> (GLW   0RGHO &$@
8-14
Maintenance anddo-it-yours elf
SDI2500
Right-Hand Drive(RHD) models
Check thefluid level inthe reservoir. Ifthe fluid is
below theMIN line
*
1
, the brake warning lightwill
illuminate. Addfluid uptothe MAX line
*
2
. (For
recommended typesoffluid, seeªRecommended
fluids/lubricants andcapacitiesº (P.9-2) .)
If the fluid must beadded frequently ,the system should
be thoroughly checkedbyaNISSAN dealer.
GUID-49CB 670B-6D6F-47EA-A1 B5-33D3AF 6563F7
WARNING:
. Use only newfluid from asealed container.
Old, inferior, orcontaminated fluidmay
damage theclutch system.
. Clean thefiller capbefore removing.
. Clutch fluidispoisonous andshould be
stored carefully inmarked containers outof
the reach ofchildren.
CAUTION:
Do not spill theclutch fluidonpainted surfaces.
This willdamage thepaint. Ifclutch fluidis
spilled, washitoff with plenty ofwater immedi-
ately.
SDI2688
Left-Hand Drive(LHD) models
SDI2500
Right-Hand Drive(RHD) models
Check thefluid level inthe reservoir. Ifthe fluid is
below theMIN line
*
1
, add fluid uptothe MAX line
*
2
. (For recommended typesoffluid, seeªRecom-
mended fluids/lubricants andcapacitiesº (P.9-2) .)
If the fluid must beadded frequently ,the clutch system
should bethoroughly checkedbyaNISSAN dealer.
CLUT CHFLUID (ifequipped)
&RQGLWLRQ

Page 184 of 217



> (GLW   0RGHO &$@
GUID-85F3 A377-AEC4-4 B2C-8B1A-DCA92F23BD68
Contact aNISSAN dealerifchecking orreplacement
is required.
CAUTION:
. Use only Genuine NISSANCVTFluid NS-3.
Do not mix with other fluids.
. Using transmission fluidother thanGenuine
NISSAN CVTFluid NS-3willdamage the
CVT ,which isnot covered bythe warranty.
GUID-31654B FB-7FD1-4485-8577-CE C93F60D8BD
SDI2667
WARNING:
Operating theengine withtheaircleaner filter
off can cause youorothers tobe burned. Theair
cleaner filternotonly cleans theintake air,it
also stops flame ifthe engine backfires. Ifthe air
cleaner filterisnot installed andtheengine
backfires, youcould beburned. Neverdrivewith
the aircleaner filteroff.Becautious workingon
the engine whentheaircleaner filterisoff.
T o remove thefilter, pulltheairduct
*
1
upward to
remove it.Pull thetabs
*
2
, then pullthecover
*
3
upward.
The viscous papertypefilterelement shouldnotbe
cleaned andreused. Thedrypaper typefilterelement
may becleaned andreused. Replace theairfilter
according tothe maintenance logshown inaseparate
maintenance booklet.
When replacing theairfilter, wipetheinside ofthe air
cleaner housing andthecover withadamp cloth.
GUID-1E8 7C0C3-19A 7-495E-AF4 8-A77448AE4962
WINDSHIELD WIPERBLADES
GUID-CB3E 500E-FF38-4 A23-B90C-E296B23CFC7 A
Cleaning
GUID-1F848 096-A502-4F6 2-82A8-5DCF0E18CBBB
If the windshield doesnotbecome clearafterusing the
windshield washerorifthe wiper blades chatter when
operating thewindshield wipers,waxorother materials
may beonthe windshield and/orwiperblades.
Clean theoutside ofthe windshield surfacewitha
washer solution ormild detergent. Your windshield is
clean ifbeads donot form when rinsing withwater.
Clean theblade bywiping itwith acloth soaked ina
washer solution oramild detergent. Rinsetheblade
with water. Ifyour windshield isstill notclear after
cleaning theblades andusing thewipers, replace the
blades.
Maintenance anddo-it-yours elf
8-15
CONTINUOUSL
YVARIABLE
TRANSMISSIO N(CVT) FLUID (if
equipped) AIR
CLEANER FILTER WIPERBLADES
&RQGLWLRQ

Page 185 of 217



> (GLW   0RGHO &$@
8-16
Maintenance anddo-it-yours elf
SDI1865
Be careful nottoclog thewasher nozzle
*
A
. This may
cause improper windshield washeroperation. Ifthe
nozzle isclogged, removeanyobjects withaneedle or
small pin
*
B
. Be careful nottodamage thenozzle.
Replacing
GUID-446 2DA2C-A6A5 -41D7-9863-C47C1EA4 8EA4
SDI1649
Replace thewiper blades ifthey areworn.
Before replacing thewiper blades, thewiper should be
in the fully upposition toavoid scratching theengine
hood ordamaging thewiper arm.To pull upthe wiper
arm, seeªWiper andwasher switchº (P.2-20) .
1. Liftthe wiper armaway fromthewindshield.
2. Push andhold therelease tab
*
A
, and then move
the wiper blade downthewiper armtoremove
*
1
.
3. Remove thewiper blade.
4. Insert thenew wiper blade ontothewiper armuntil
it clicks intoplace.
CAUTION:
. After wiper blade replacement, returnthe
wiper armtoits original position. Otherwise
the wiper armorthe engine hoodmaybe
scratched andmay cause damage whenthe
engine hoodisopened.
. Worn wiper blades candamage thewind-
shield andimpair drivervision.
REAR WINDOW WIPERBLADE
GUID-BFB 99CBF-6874-4939-8C 1C-B539C65 1C360
Contact aNISSAN dealerifchecking orreplacement
is required.
&RQGLWLRQ

Page:   < prev 1-10 11-20 21-30 31-40 next >