change language NISSAN QASHQAI 2007 Owners Manual

Downloaded from www.Manualslib.com manuals search engine For more information, contact your NISSAN dealer
or qualified workshop.
[Language]
Select the submenu to set the desired language of
the display
[Factory]
Select the submenu to reset the factory settings of
the display.
NOTE
When resetting [Factory], all previous settings
made are changed to default.
CRUISE CONTROL/SPEED LIMITER
INDICATOR (where fitted)
The CRUISE indicator is displayed when the
cruise control main “ON/OFF” switch is pushed.
When the main switch is pushed again, theCRUISE indicator disappears. When the
CRUISE indicator is displayed, the cruise con-
trol system is operational.
The cruise control SET indicator is displayed
while the vehicle speed is controlled by the cruise
control system. If the SET indicator blinks while
the engine is running, it may indicate that the
cruise control system is not functioning properly.
Have the system checked by an NISSAN dealer
or qualified workshop.
For more details, see “Cruise control (where
fitted)” in the “5. Starting and driving” section.
The LIMIT indicator is displayed when the speed
limiter main “ON/OFF” switch is pushed. When
the main switch is pushed again, the LIMIT indi-
cator disappears.
When the LIMIT indicator is displayed, the speed
limiter is operational. The speed limiter is active,
when the SET indicator is displayed.
For more details, see “Speed limiter” in the
“5. Starting and driving” section.
When the trip computer was set before using the
cruise control or speed limiter function, the trip com-
puter menu item
jA is shown together with the
cruise control or speed limiter. See “Trip computer”
earlier in this section
WARNING
In freezing temperatures the washer fluid may
freeze on the windscreen and obscure your vi-
sion. Warm the windscreen with the defroster
before you wash it.
CAUTION
Do not open/release the bonnet when the
front wiper arms are raised from their original
position.
Do not operate the washer continuously for
more than 15 seconds.
Do not operate the washer if the reservoir
tank is empty or frozen.
NIC1550
WIPER AND WASHER SWITCH
Instruments and controls2-21

Downloaded from www.Manualslib.com manuals search engine When the<CD>or<AUX> button is pressed
during a NEWS interruption, the NEWS standby
mode remains active.
However, if the button is pressed and
the radio wave band changes to the MW or LW,
then the NEWS standby mode will be switched
off.
MENU BUTTON
To configure Alternative Frequency (AF), Regional
(REG) and Language settings, perform the follow-
ing procedure:
1) Press and hold the <MENU>button for at least
1.5 seconds.
2) Turn the MENU/VOL dial clockwise or anticlock- wise, the display message will appear in the fol-
lowing order:
[AF] ⇔[REG] ⇔[LANGUAGE] ⇔[AF]
To activate or deactivate the AF and REG mode,
briefly press the <ENTER>button when [AF] or
[REG] appears in the display and turn the MENU/
VOL dial clockwise or anticlockwise to switch
between the on or off position. After selection,
press the <ENTER> button to save the settings.
– When the AF mode is enabled, the audio unit will automatically re-tune to a stronger fre-
quency if the radio signal becomes weak.
– When the REG mode is enabled, the audio unit will maintain and hold the station which is
broadcasting local (regional) programmes.
To change the display language, briefly press on
the <ENTER> button when LANGUAGE
appears in the display then turn the MENU/VOL
dial clockwise or anticlockwise to select the ap-
propriate language setting.
[ENGLISH] ⇔[DUTCH] ⇔[FRENCH] ⇔
[SPANISH] ⇔[GERMAN] ⇔[ITALIAN] ⇔
[PORTUGUESE] ⇔[ENGLISH]
After selecting the desired language, press the
<ENTER> button to save the setting.
After the desired levels have been set, press either
the <MENU> button for at least 1.5 seconds, the
<BACK> button, or wait for 5 seconds without
pressing any buttons to exit the menu screen.
To configure the [SPEED VOL] (Volume) and
[BEEP] settings, perform the following procedure:
1) Briefly press the <MENU>button.
2) Turn the MENU/VOL dial clockwise or anticlock- wise, the display message will appear in the fol-
lowing order:
[PHONE SETUP] ⇔[SPEED VOL] ⇔[BEEP]
⇔ [PHONE SETUP]
When [SPEED VOL] is displayed, briefly press
the <ENTER> button then turn the MENU/VOL
dial clockwise or anticlockwise to adjust the level
of the volume.
Adjusting the setting to 0 (zero) turns off the
speed volume feature. Increasing the speed vol-
ume setting results in the audio volume increas- ing more rapidly with vehicle speed. Press the
<ENTER>
button again to save the setting.
When [BEEP] appears in the display, briefly
press the <ENTER> button and then turn the
MENU/VOL dial clockwise or anticlockwise to
switch the beep sound on or off. When this item
is turned on, you will hear a beep sound when
you use a button. Press the <ENTER>button
again to save the setting.
After the desired levels have been set, press either
the <MENU> button, the <BACK>button, or wait
for 10 seconds without pressing any buttons to exit
the menu screen.
COMPACT DISC (CD) OPERATION
Turn the ignition switch to the Acc or ON position,
press the <CD>button and the CD mode will start
to play the CD.
When the <CD>button is pressed and the radio
mode or AUX mode is already operating, it will auto-
matically turn off and the CD mode will start.
However, if the CD is not loaded, then a notification
message will be displayed and the audio unit re-
mains in radio mode or AUX mode.
CAUTION
Do not force the CD into the slot. This could
damage the player.
Do not use 8 cm (3.1 in) discs.
Display screen, heater and air conditioner, and audio system4-27

Downloaded from www.Manualslib.com manuals search engine Eighteen stations can be stored in the FM band.
(Six each for FM1, FM2 and FMT)
Six stations can be set for the AM band.
If the battery is disconnected, or if the fuse blows,
the radio memory will be erased. In that case, reset
the desired stations after battery connection or fuse
replacement.
Radio data system (RDS) operation
The RDS is a system through which encoded digital
information is transmitted by FM radio stations in
addition to the normal FM radio broadcasting. The
RDS provides information services such as station
name, traffic information, or news.
NOTE
In some countries or regions, some of these ser-
vices may not be available.
Alternative Frequency (AF) mode:
The AF mode operates in the FM (radio) mode.
The AF mode operates in the FM (radio), AUX or
CD mode (if FM was previously selected in the
radio mode).
The AF function compares signal strengths and
selects the station with the optimum reception
conditions for the currently tuned-in station.
RDS functions
Programme Service (PS) function (station name
display function):
When an RDS station is tuned in with seek or manual
tuning, the RDS data is received and the PS name
is displayed.
TA Traffic announcement
This function operates in FM (Radio), CD or AUX
mode.
Pressing the <TA>button selects the TA mode.
The TA indicator is displayed while TA mode is
on.
When <TA>is pressed again. The mode will be
switched off and the TA indicator will disappear
from the display.
Traffic announcement interrupt function:
When a traffic announcement is received, the an-
nouncement is tuned in and the display shows a
notification message with the radio station name e.g.
[TA: Radio 1].
Once the traffic announcement has finished, the unit
returns to the source that was active before the traf-
fic announcement started.
If <TA> is pressed during a traffic announcement,
the traffic announcement interrupt mode is can-
celled. The TA mode returns to the standby mode
and the audio unit returns to the previous source.
SETUP BUTTON
To configure Audio, Clock, Bluetooth, Language or
Scroll direction settings, perform the following pro-
cedure:
1. Press the <SETUP>button.
2. Turn the <TUNE/MENU> dial clockwise or anti-
clockwise, the display will appear in the following
order:
[Audio] ⇔[Clock] ⇔[Bluetooth] ⇔[Language]
⇔ [Scroll Direction]
After the desired levels have been set, press either
the
(Back) button repeatedly, the <SETUP>
button, or wait for 8 seconds without pressing any
buttons to exit the menu screen.
Display brightness (Day/Night mode)
Press the <SETUP> button with a long press to
switch the display brightness between the daytime
and nighttime mode.
Audio adjustments
Press the <SETUP> button to enter the setup menu
screen then select [Audio].
Each time the <ENTER>button is pressed, the mode
will change as follows:
[Bass] →[Treble] →[Balance] →[Fade] →[AUX
VOL] →[SPD VOL] →setup menu screen [Audio]
→ [Bass]
Display screen, heater and air conditioner, and audio system4-33