light NISSAN QUEST 2006 V42 / 3.G Quick Reference Guide

SUNROOF CONTROLS (if so equipped)
 To tilt the sunroof up, press UP. (If the roof is already
open, it will close before tilting up.) To tilt the sunroof
down, press doWn
.
 To open partially, slide the switch toward oPen. (If the
roof is tilted up, it will automatically tilt down before
opening.) To open fully, slide the switch completely to
oP en
.
 To close partially, slide the switch toward Close . To
close fully, slide the switch completely to Close .
CHILD SAFET Y DOOR LOCK
Child safety locks help prevent the sliding doors from being
opened accidentally, especially when small children are in
the vehicle. The child safety lock levers are located on the
edge of the sliding doors. When the lever is in the loCK

position, the door can be opened only from the outside, with
the overhead console switch or the keyfob.
POWER SLIDING DOORS AND POWER BACK DOOR (if so equipped)
POWER SLIDING DOORS
The power sliding doors can be
activated by the buttons on the keyfob, the overhead console, and the door pillars.
 To open, close or reverse a sliding door, the ignition switch must be off or the
automatic transmission selector lever must be in Park.
 To open, close or reverse a sliding door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To activate a sliding door with the button on the door pillar, the main on /o FF switch
must be on, the door must be unlocked, and the child safety door lock must be in the
unlock position.
 To activate the power assist feature, manually move a sliding door toward the open
or close position using the inside or outside handle. The power assist feature will
automatically complete the motion.
P OWER BACK DOOR
The power back door can be activated by the buttons on the keyfob, the overhead
console, and the rear door pillar.
 To open, close or reverse the back door, the automatic transmission lever must be
in Park.
 To open, close or reverse the back door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To close the back door with the rear door pillar button, the main on/oFF switch
must be on.
The power sliding doors and the power back door have an anti-pinch safety feature.
Please refer to your Owner’s Manual for more information regarding this feature.
AUTOMATIC DRIVER POSITIONER (if so equipped)
The automatic driver positioner system has two features:
 Memory storage function
 Entry/exit function
MEMORY STOR AGE FUNCTION
Two positions for the driver’s seat, accelerator and brake
pedals, and outside mirrors can be stored in the automatic driver positioner memory.
Follow these procedures to set driver preferences.
SET THE DESIRED POSITIONING
1. Set the automatic transmission lever to the Park position.
2. Turn the ignition on and adjust the driver’s seat, accelerator and brake pedals, and
outside mirrors to the desired positions.
3. Press the
set (memory) button and within 5 seconds press the position button (1 or 2 ) for at least 1 second until the indicator light illuminates. The position is now
stored in memory.
LINK TO KEYFOB
 Within 5 seconds of setting the memory position (indicator light is on and ignition is
on), press the
button
on the remote.
 A keyfob can be linked to each memory button.
 If memory positioning is re-set to a new location, the keyfob automatically re-links.
RECALLING A MEMORY SET TING FROM THE MEMORY PAD
 With the automatic transmission lever in the Park position, press the position button (1 or 2 ) for at least 1 second.
FROM THE KEYFOB
 If properly linked, operation of the button
will automatically return the driver’s
seat, accelerator and brake pedals, and mirrors to the memorized position.
ENTRY/ EXIT FUNCTION
The driver’s seat moves to allow the driver to get into and out of the driver’s seat more
easily. The driver’s seat slides backward when:
 The key is removed from the ignition switch.
 The driver’s door is opened with the key turned to LOCK.
 The key is turned from ACC to LOCK with the driver’s door open and the automatic
transmission lever is in the Park position.
The driver’s seat returns to the previous position when:
 The key is inserted into the ignition switch.
 The driver’s door is closed with the key turned to LOCK.
 The key is turned from ACC to ON while the automatic transmission lever is in the
Park position.
REAR SONAR SYSTEM OFF SWITCH (if so equipped)
When backing up, this system will beep to alert you to obstacles
within 6 ft. of the rear bumper. The system beeps faster as the vehicle
gets closer to the obstacle. A continuous tone sounds when an
obstacle is less than 10 inches away from the bumper. Turn the system
off by pushing the rear sonar system
oFF switch. The system will
automatically reset the next time the ignition switch is turned on.
ADJUSTABLE A CCELERATOR AND BRAKE P EDALS (if so equipped)
The accelerator and brake pedals can be adjusted for your
driving comfort.
 Adjust the pedals when the automatic transmission lever
is in Park.
 Push to
move the position of the pedals forward. 01
 Push to
move the position of the pedals backward. 02
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
 Pull up on the lever under the front of the seat and
slide backward or forward; release.
01
 Lift the lever on the side of the seat to adjust your
seatback backward or forward; release when you
have found a comfortable angle and the seat belt
fits properly.
02
 Use the dials at the side of the driver’s seat to
adjust the angle and height of the seat

cushion.
03
With power seats (if so equipped):
 Move the control forward or backward to adjust
the seat cushion forward or backward.
04
 Pull up to raise the driver’s seat cushion; press
down to lower the cushion.
04
 Push the switch forward to move the seatback
forward; press it back to move the seatback
backward.
05
Your driver’s seat has a lumbar support; adjust it by
moving the lever forward or backward.
06
to fold the 3rd row bench seat flat into the floor for maximum cargo hauling:
 Remove all 3 head restraints. Remove the head restraints by lifting up, then press
and hold the release button and continue lifting and place the head restraints in the
storage bag.
 Disconnect and secure the center seat belt and tongues into the retractor base.
Then, press the button on the seatback while pulling back on the strap to release the
back of the seat.
01
 Rotate the seatback toward the back of the vehicle. 02
 Pull up on the lever located on the back of the seat base. This will fold the seat base
toward the back of the vehicle.
03
 The entire seat will rotate toward you and stow flat in the floor. 04
 Reverse this process to return the bench seat to a seating position. Make sure to
properly install the head restraints, reattach the center seat belt, press the bench
seat down into the floor, and pull back on the seatback until it latches into place.
Sh ift_convention
to move the 2nd row seats forward or backward:
 Pull the lever up and hold it while you slide the seat forward or backward to the
desired position.
01
 Release the lever to lock the seat in position.
t o recline the 2nd row seatbacks:
 Pull the lever up and lean forward or back. 02
the 2nd row seats can be tipped forward for easy entry or exit from the 3rd row seat:
 To enter the 3rd row seats, lift up on the lever located on the lower base of the seat;
this tips the seat forward.
03
 To exit the 3rd row seats, pull back on the lever on the lower base of the seat and
push the seat forward.
t o fold the 2nd row seats flat to the floor for maximum cargo hauling:
 Remove the head restraints by lifting up each head restraint. Then, press and hold
the release button and place the head restraints in the storage bag.
 Lift up on the recline lever to fold the seatback down on the seat base. 04
 Press down on the small lever on the back of the seat to release the base of
the seat.
05
 Then fold the entire seat forward into the stowed position on the floor. 06
 Reverse this process to return the 2nd row seats to a seating position. Make sure to
properly install the head restraints and to press the seats down to the floor until they
latch into place.
ADJUSTING AND FOLDING THE 2ND ROW SEAT
01
02
FOLDING THE 3RD ROW SEAT
lo CK doo Rs
Make sure all doors and windows are closed and
press the LOCK button to secure the vehicle.
U nlo CK doo Rs
Press the UNLOCK button once to unlock the
driver’s door. Press the UNLOCK button twice
within 5 seconds to unlock all doors.
P o W eR sliding doo Rs
Press and hold the POWER SLIDING DOOR
button (if so equipped) for longer than 0.5
seconds to open or close the power sliding
door. The door will reverse direction immediately
during power open or power close if the keyfob
button is pressed. A chime will sound to indicate
the reversal.
P o W eR B aCK doo R
Press and hold the POWER BACK DOOR button (if so equipped) for longer
than 0.5 seconds to open or close the power back door. The hazard lights
will flash and a chime will sound to indicate that the power open or power
close sequence has started. If you press the button again, the door will
reverse direction immediately; a chime will sound to indicate the reversal.
R emote o Pening o F FR ont Windo Ws
Press the UNLOCK button longer than 3 seconds to open the windows. (The keyfob

is not able to close the windows after opening them.)
REMOTE KEYLESS ENTRY SYSTEM
01
02
03
04
05
06
01
0203
04
05
06
01
02
03
04
FUEL FILLER LID RELEASE
To open, press the fuel filler lid release located on the
driver’s door. To lock, securely close the fuel filler lid.

The driver’s side power sliding door is disabled when the
fuel lid is open. The sliding door can be partially opened
manually.
DOOR LOCK SWITCH
The door lock switch is located on the driver’s door armrest. Push top
of switch
01 to lock all the doors. Push bottom of the switch 02 to
unlock all the doors.
2006
QU EST

Q U I C K R E F E R E N C E G U I D E

REAR VIEW MONITOR
(if so equipped)
When the automatic transmission lever is moved to the R
(Reverse) position, the monitor display will automatically
change to show the area behind the vehicle.
The colored lines on the display screen indicate approximate
distances to objects.
 Red 1.5 feet  Yellow 3 feet  Green 7 and 10 feet
01
02

02
03
04
07
01
06
05
QR6E-0V42U1 Printing: February 2006 (08)
Nissan, the Nissan Brand Symbol, “SHIFT_” tagline, Z and Nissan model names are Nissan trademarks.
©2006 Nissan North America, Inc.
HE ADLIGHT CONTROL
LIGHTS ON DEMAND
STEERING WHEEL
TILT ADJUSTMENT ( BEHIND STEERING WHEEL)
CRUISE CONTROL
WINDSHIELD WIPER/
WASHER CONTROL S
CLIMATE
CONTROLS
TIRE PRESSURE
MONITORING SYSTEM
TRIP BUT TON
OUTSIDE MIRROR CONTROL
STEERING WHEEL SWITCHES
FOR AUDIO CONTROL
DISPL AY SCREEN
AUDIO SYSTEM
Sh ift_
LIGHTS ON DEMAND
The
lights on demand switch allows the driver
to select one of three lighting modes for the interior
lights and puddle lamps (if so equipped): on, door, off.
Push the top portion of the switch and the
interior lights and puddle lamps will illuminate;
they will turn off automatically after 30 minutes,
to prevent the battery from becoming
discharged.
If the
lights on demand switch is in the neutral position, the lights will
stay on for about 30 seconds when:
 The doors are unlocked by the keyfob, a key, or the power door lock switch
while all doors are closed and the ignition switch is in the OFF position.
 The driver’s door is opened and then closed while the key is removed from the
ignition switch.
 The key is removed from the ignition switch while all doors are closed.
The interior lights and puddle lamps (if so equipped) will turn off while the

30-second timer is activated when:
 The driver’s door is locked by the keyfob, a key, or the power door lock switch.
 The ignition switch is turned on.
The lights will turn off automatically after 30 minutes while the doors are open to
prevent the battery from becoming discharged.
Push the bottom portion of the switch and the interior lights and puddle
lamps (if so equipped) will be turned off.
 The lights can be turned off so sleeping passengers are not disturbed when
the doors are opened.
 The lights on the front doors will turn on when the front doors are opened.
04
05TRIP BUTTON
When t R iP is pressed, the following modes will
display on the screen:
 TRIP 1 – TIME, DIST, AVG
 TRIP 2 – TIME, DIST, AVG
 OFF
TRIP 1 or TRIP 2 record journey time, trip odometer and average speed.
To reset TRIP 1 and TRIP 2, use the joystick to select R eset ; press ente R or
t R iP for approximately 2 seconds.
03
RE AR SONAR SWITCH
01
see K/tR aCK BU tton
To scan quickly through each broadcasting station, press the see K/tRa CK button.
The tuner will pause for 5 seconds on each broadcasting station. To skip from one
track to another on a CD, press the see K/tRa CK button. Each time the button is
pressed, the CD will advance or skip back one track.
t U ne /ReW/FF BU tton
To fast forward or rewind a track, press the ReW/FF button. The disc will play at

an altered speed until the button is released. To manually tune the radio, press the
tU ne button.
PR og /RP t BU tton
To change the play pattern of the CD, press the PRog /RPt button. To activate the
Radio Data System (RDS), press the PRog /RPt button. RDS provides information
about radio stations (type, call numbers, etc.)
PR eset a · B · C BU tton
Press PR eset a-B-C button until you reach the desired setting. The radio is

equipped with three separate banks of six station presets (18 total station presets).
You may store any combination of AM, FM or SAT* radio presets on each bank.
C d P la Y BU tton
To begin play, press the Cd button.
R ea R aV BU tton

To turn the rear audio controls on, press the ReaR aV button. Press again to turn
rear controller off. To turn on the DVD mode (if so equipped), press and hold the
R eaR aV button for 2 seconds.
s Pea KeR C ont Rol BU tton
To activate the rear headphones and turn off the rear speakers, press the SPEAKER
CONTROL button. To deactivate the rear headphones, press the button again.
t U ning and a U dio Cont Rol Kno B
To manually tune the radio, turn the tUne knob. Adjust the bass , treble, fade,

balance, and Speed Sensitive Volume (SSV) by pressing the aU dio knob until the
desired mode appears in the display. Then turn the tUne knob to adjust to the
desired level.
station and Cd sele Ct BU ttons
To store a station in a preset you must first select A, B, or C memory bank by pressing
the PR eset a·B·C button and tune to the desired AM, FM or SAT* station. Then

press the desired station select button for at least 2 seconds. When the preset
indicator illuminates, a beep will sound, indicating memorization is complete. To retrieve
a previously set station, select the memory bank where the preset was set, then press
the corresponding station select button.
AUDIO
SYSTEM
06
* SAT presets are only available on SAT equipped vehicles.
05
04
03
02
01
06
07
08
09
SEAT BELT WARNING LIGHT AND CHIME
 The light and chime remind you to fasten your seat
belts. The light illuminates whenever the ignition key
is turned to the ON or START position and remains
illuminated until the driver’s seat belt is fastened. At
the same time, the chime sounds for about 6 seconds
unless the driver’s seat belt is securely fastened.
 The seat belt warning light may also illuminate if the front passenger’s seat belt is
not fastened when the front passenger’s seat is occupied (if so equipped). For 5
seconds after the ignition switch is in the ON position, the system does not activate
the warning light for the front passenger.
Refer to the Owner’s Manual for detailed information regarding seat belt usage.

This easy-to-use Quick Reference Guide is intended to help you more fully appreciate
some of the unique features and functions of your new vehicle. However, it is not intended
to replace your Owner’s Manual. The Owner’s Manual contains more detailed information
to help you better understand the important safety warnings, features, operation, and
maintenance of your vehicle.
02STEERING WHEEL SWITCHES FOR
AUDIO CONTROL (if so equipped)
 To turn steering wheel audio system on,
push Po W eR
.
 Push the
mode button to change the mode in
the following sequence: Preset radio station bank

( A or B or C)
CD (if a CD is in the player)
SAT (if equipped) DVD (if equipped).
DVD will show in the display even if there is no DVD in the player.
 The < > switch can be used to perform the following:
• Push the
< >
switch
for less than 1.5 seconds to change to the preset station.
• Push the < > switch for more than 1.5 seconds to seek to the next
broadcasting radio station.
• Push the
< > switch while playing a CD for less than 1.5 seconds to change
programs on the CD.
• If the vehicle is equipped with a 6 Disc CD changer, push the
< > switch for
more than 1.5 seconds to change between CDs.
 Push the Vol control switch or to increase or decrease volume.
AD D ITIONAL FEATU R E S
TIRE PRESSURE MONITORING SYSTEM (TPMS)
This system monitors tire pressure. Please remember, this
system does not detect a sudden drop in tire pressure (for
example, a blowout while driving). It also does not monitor the
air pressure in the spare tire.
Tire pressure is affected by temperature. Low outside temperature causes lower
tire pressure. This may cause the low tire pressure warning light to illuminate.
If the low tire pressure warning light comes on, check the tire pressure in all four
tires. Adjust the low tire pressure to the recommended
COLD tire pressure shown
on the Tire and Loading Information label to turn the low tire pressure warning light
off .
If TPMS is not functioning properly, the low tire pressure warning light will flash for

approximately 60 seconds when the key is turned on. After 60 seconds, the light
will remain on. Have the system checked by a NISSAN dealer.
A UTOMATIC CLIMATE CONTROL (if so equipped)07
0201
05
0704
08
09
03
06
080607050302
01
09
04
CRUISE CONTROL
 To initiate cruise control, push on. (The CRU ise
indicator light will illuminate.)
 To set a cruising speed, accelerate to the desired
speed, push C oast /set and release. (The
set
indicator light will illuminate.)
 To set a faster or slower cruising speed:
• Press on the brake or accelerator to attain the desired speed, push
Coast/ set, and release.
• Push and hold the aCC el/R es switch to increase speed. Release the
switch when the vehicle attains the desired speed. Push and release the
aCC el/R es switch to increase speed by about 1 MPH.
• Push and hold the Coast/ set switch to decrease speed. Release the
switch when the vehicle attains the desired speed. Push and release the
Coast/ set switch to decrease speed by about 1 MPH.
 To resume a preset speed, push a CC el/R es and release.
 To cancel cruise control, push the C an Cel switch or tap the brake pedal. The
SET indicator light in the instrument panel will go out.
 To turn off cruise control, push the main ( on /o FF ) switch. Both the CRUISE
indicator light and the SET light in the instrument panel will go out. a
U to BU tton
 Press the aUto button
01. Turn the driver’s side temperature control dial 02
to the desired temperature. This will allow the fan speed, air flow distribution and
temperature to be automatically maintained.
 Press the aUto button a second time to turn the passenger’s side temperature
controls on or off. This will allow the passenger’s side temperature to be
adjusted independently from driver’s side control.
 When aUto is pressed, aUto will be displayed. When aUto is pressed a
second time, dUal will be displayed.
d RiV e R’ s side tem Pe R at UR e C ont Rol dial
Turn the driver’s temperature control dial left for cold air or right for hot air.
P assenge R’s side tem Pe R at UR e C ont Rol dial
Turn the passenger’s temperature control dial left for cold air or right for hot air.
ai R F loW mode Cont Rol BU tton
Press
mode button repeatedly to scroll through the following air flow outlets: Air flows from the center and side vents.
Air flows from the center, side, and foot vents.
Air flows mainly from the foot vents.
Air flows from the defroster and foot vents.
Air flows mainly from the defroster vents.
F an s Peed Cont Rol dial
Turn the fan speed control dial
to
the left (slower) or right (faster) to manually
control fan speed. Press aUto to automatically control fan speed.
de FRosting /de Fogging FRont and side Windo Ws
 Press the defroster control button to
turn the system on. The A/C
automatically turns on when the defroster mode is selected.
 Turn the driver’s side temperature control dial left or right to set the desired temperature.
 To set the defroster on high, turn the fan speed dial all the way to the right.
de FRosting /de Fogging Rea R W indo W and (if so equipped) oUtside
heated mi RR oR

Push the rear window defroster switch on.
Push the switch again to manually
turn the defroster off. This function automatically turns off in approximately 15
minutes.
a /C on /o FF BU tton
Press the a/C button to manually turn the A/C on or off.
ai R R eC iRCU lation BUtton
 Press the air recirculation button to
recirculate air inside the vehicle.
 Press the air recirculation button again
to turn air recirculation off.
 The air recirculation mode cannot be selected if the air flow control dial is in the
defrost position .
05
04
03
02
01
06
07
08
09
FRONT-PASSENGER AIR BAG STATUS LIGHT
This vehicle is equipped with the Nissan Advanced Air
Bag system. Under some conditions, depending on
pressure detected on the passenger seat and how the
seat belt is used, the front-passenger air bag is designed
to automatically turn oFF. When the front-passenger air
bag is oFF , the front-passenger air bag status light will
illuminate*. For example:
 When the system detects that the front-passenger’s seat is occupied by a small
adult, child or child restraint as outlined in the Owner’s Manual, the
Pass
ai R Bag
oFF or will illuminate to indicate that the front-passenger air bag is oFF and will not inflate in a crash.
 When the front-passenger’s seat is occupied and the passenger meets the
conditions outlined in the Owner’s Manual, the
Pass
ai R Bag
oFF or will not illuminate to
indicate that the front-passenger air bag is operational.
*When the system detects that the front-passenger’s seat is unoccupied, the passenger air bag status light will not illuminate even though the front-passenger
air bag is oFF.
Refer to the Owner’s Manual for detailed information regarding the Nissan Advanced Air
Bag System.

02
03
04
07
01
06
05
QR6E-0V42U1 Printing: February 2006 (08)
Nissan, the Nissan Brand Symbol, “SHIFT_” tagline, Z and Nissan model names are Nissan trademarks.
©2006 Nissan North America, Inc.
HE ADLIGHT CONTROL
LIGHTS ON DEMAND
STEERING WHEEL
TILT ADJUSTMENT ( BEHIND STEERING WHEEL)
CRUISE CONTROL
WINDSHIELD WIPER/
WASHER CONTROL S
CLIMATE
CONTROLS
TIRE PRESSURE
MONITORING SYSTEM
TRIP BUT TON
OUTSIDE MIRROR CONTROL
STEERING WHEEL SWITCHES
FOR AUDIO CONTROL
DISPL AY SCREEN
AUDIO SYSTEM
Sh ift_
LIGHTS ON DEMAND
The
lights on demand switch allows the driver
to select one of three lighting modes for the interior
lights and puddle lamps (if so equipped): on, door, off.
Push the top portion of the switch and the
interior lights and puddle lamps will illuminate;
they will turn off automatically after 30 minutes,
to prevent the battery from becoming
discharged.
If the
lights on demand switch is in the neutral position, the lights will
stay on for about 30 seconds when:
 The doors are unlocked by the keyfob, a key, or the power door lock switch
while all doors are closed and the ignition switch is in the OFF position.
 The driver’s door is opened and then closed while the key is removed from the
ignition switch.
 The key is removed from the ignition switch while all doors are closed.
The interior lights and puddle lamps (if so equipped) will turn off while the

30-second timer is activated when:
 The driver’s door is locked by the keyfob, a key, or the power door lock switch.
 The ignition switch is turned on.
The lights will turn off automatically after 30 minutes while the doors are open to
prevent the battery from becoming discharged.
Push the bottom portion of the switch and the interior lights and puddle
lamps (if so equipped) will be turned off.
 The lights can be turned off so sleeping passengers are not disturbed when
the doors are opened.
 The lights on the front doors will turn on when the front doors are opened.
04
05TRIP BUTTON
When t R iP is pressed, the following modes will
display on the screen:
 TRIP 1 – TIME, DIST, AVG
 TRIP 2 – TIME, DIST, AVG
 OFF
TRIP 1 or TRIP 2 record journey time, trip odometer and average speed.
To reset TRIP 1 and TRIP 2, use the joystick to select R eset ; press ente R or
t R iP for approximately 2 seconds.
03
RE AR SONAR SWITCH
01
see K/tR aCK BU tton
To scan quickly through each broadcasting station, press the see K/tRa CK button.
The tuner will pause for 5 seconds on each broadcasting station. To skip from one
track to another on a CD, press the see K/tRa CK button. Each time the button is
pressed, the CD will advance or skip back one track.
t U ne /ReW/FF BU tton
To fast forward or rewind a track, press the ReW/FF button. The disc will play at

an altered speed until the button is released. To manually tune the radio, press the
tU ne button.
PR og /RP t BU tton
To change the play pattern of the CD, press the PRog /RPt button. To activate the
Radio Data System (RDS), press the PRog /RPt button. RDS provides information
about radio stations (type, call numbers, etc.)
PR eset a · B · C BU tton
Press PR eset a-B-C button until you reach the desired setting. The radio is

equipped with three separate banks of six station presets (18 total station presets).
You may store any combination of AM, FM or SAT* radio presets on each bank.
C d P la Y BU tton
To begin play, press the Cd button.
R ea R aV BU tton

To turn the rear audio controls on, press the ReaR aV button. Press again to turn
rear controller off. To turn on the DVD mode (if so equipped), press and hold the
R eaR aV button for 2 seconds.
s Pea KeR C ont Rol BU tton
To activate the rear headphones and turn off the rear speakers, press the SPEAKER
CONTROL button. To deactivate the rear headphones, press the button again.
t U ning and a U dio Cont Rol Kno B
To manually tune the radio, turn the tUne knob. Adjust the bass , treble, fade,

balance, and Speed Sensitive Volume (SSV) by pressing the aU dio knob until the
desired mode appears in the display. Then turn the tUne knob to adjust to the
desired level.
station and Cd sele Ct BU ttons
To store a station in a preset you must first select A, B, or C memory bank by pressing
the PR eset a·B·C button and tune to the desired AM, FM or SAT* station. Then

press the desired station select button for at least 2 seconds. When the preset
indicator illuminates, a beep will sound, indicating memorization is complete. To retrieve
a previously set station, select the memory bank where the preset was set, then press
the corresponding station select button.
AUDIO
SYSTEM
06
* SAT presets are only available on SAT equipped vehicles.
05
04
03
02
01
06
07
08
09
SEAT BELT WARNING LIGHT AND CHIME
 The light and chime remind you to fasten your seat
belts. The light illuminates whenever the ignition key
is turned to the ON or START position and remains
illuminated until the driver’s seat belt is fastened. At
the same time, the chime sounds for about 6 seconds
unless the driver’s seat belt is securely fastened.
 The seat belt warning light may also illuminate if the front passenger’s seat belt is
not fastened when the front passenger’s seat is occupied (if so equipped). For 5
seconds after the ignition switch is in the ON position, the system does not activate
the warning light for the front passenger.
Refer to the Owner’s Manual for detailed information regarding seat belt usage.

This easy-to-use Quick Reference Guide is intended to help you more fully appreciate
some of the unique features and functions of your new vehicle. However, it is not intended
to replace your Owner’s Manual. The Owner’s Manual contains more detailed information
to help you better understand the important safety warnings, features, operation, and
maintenance of your vehicle.
02STEERING WHEEL SWITCHES FOR
AUDIO CONTROL (if so equipped)
 To turn steering wheel audio system on,
push Po W eR
.
 Push the
mode button to change the mode in
the following sequence: Preset radio station bank

( A or B or C)
CD (if a CD is in the player)
SAT (if equipped) DVD (if equipped).
DVD will show in the display even if there is no DVD in the player.
 The < > switch can be used to perform the following:
• Push the
< >
switch
for less than 1.5 seconds to change to the preset station.
• Push the < > switch for more than 1.5 seconds to seek to the next
broadcasting radio station.
• Push the
< > switch while playing a CD for less than 1.5 seconds to change
programs on the CD.
• If the vehicle is equipped with a 6 Disc CD changer, push the
< > switch for
more than 1.5 seconds to change between CDs.
 Push the Vol control switch or to increase or decrease volume.
AD D ITIONAL FEATU R E S
TIRE PRESSURE MONITORING SYSTEM (TPMS)
This system monitors tire pressure. Please remember, this
system does not detect a sudden drop in tire pressure (for
example, a blowout while driving). It also does not monitor the
air pressure in the spare tire.
Tire pressure is affected by temperature. Low outside temperature causes lower
tire pressure. This may cause the low tire pressure warning light to illuminate.
If the low tire pressure warning light comes on, check the tire pressure in all four
tires. Adjust the low tire pressure to the recommended
COLD tire pressure shown
on the Tire and Loading Information label to turn the low tire pressure warning light
off .
If TPMS is not functioning properly, the low tire pressure warning light will flash for

approximately 60 seconds when the key is turned on. After 60 seconds, the light
will remain on. Have the system checked by a NISSAN dealer.
A UTOMATIC CLIMATE CONTROL (if so equipped)07
0201
05
0704
08
09
03
06
080607050302
01
09
04
CRUISE CONTROL
 To initiate cruise control, push on. (The CRU ise
indicator light will illuminate.)
 To set a cruising speed, accelerate to the desired
speed, push C oast /set and release. (The
set
indicator light will illuminate.)
 To set a faster or slower cruising speed:
• Press on the brake or accelerator to attain the desired speed, push
Coast/ set, and release.
• Push and hold the aCC el/R es switch to increase speed. Release the
switch when the vehicle attains the desired speed. Push and release the
aCC el/R es switch to increase speed by about 1 MPH.
• Push and hold the Coast/ set switch to decrease speed. Release the
switch when the vehicle attains the desired speed. Push and release the
Coast/ set switch to decrease speed by about 1 MPH.
 To resume a preset speed, push a CC el/R es and release.
 To cancel cruise control, push the C an Cel switch or tap the brake pedal. The
SET indicator light in the instrument panel will go out.
 To turn off cruise control, push the main ( on /o FF ) switch. Both the CRUISE
indicator light and the SET light in the instrument panel will go out. a
U to BU tton
 Press the aUto button
01. Turn the driver’s side temperature control dial 02
to the desired temperature. This will allow the fan speed, air flow distribution and
temperature to be automatically maintained.
 Press the aUto button a second time to turn the passenger’s side temperature
controls on or off. This will allow the passenger’s side temperature to be
adjusted independently from driver’s side control.
 When aUto is pressed, aUto will be displayed. When aUto is pressed a
second time, dUal will be displayed.
d RiV e R’ s side tem Pe R at UR e C ont Rol dial
Turn the driver’s temperature control dial left for cold air or right for hot air.
P assenge R’s side tem Pe R at UR e C ont Rol dial
Turn the passenger’s temperature control dial left for cold air or right for hot air.
ai R F loW mode Cont Rol BU tton
Press
mode button repeatedly to scroll through the following air flow outlets: Air flows from the center and side vents.
Air flows from the center, side, and foot vents.
Air flows mainly from the foot vents.
Air flows from the defroster and foot vents.
Air flows mainly from the defroster vents.
F an s Peed Cont Rol dial
Turn the fan speed control dial
to
the left (slower) or right (faster) to manually
control fan speed. Press aUto to automatically control fan speed.
de FRosting /de Fogging FRont and side Windo Ws
 Press the defroster control button to
turn the system on. The A/C
automatically turns on when the defroster mode is selected.
 Turn the driver’s side temperature control dial left or right to set the desired temperature.
 To set the defroster on high, turn the fan speed dial all the way to the right.
de FRosting /de Fogging Rea R W indo W and (if so equipped) oUtside
heated mi RR oR

Push the rear window defroster switch on.
Push the switch again to manually
turn the defroster off. This function automatically turns off in approximately 15
minutes.
a /C on /o FF BU tton
Press the a/C button to manually turn the A/C on or off.
ai R R eC iRCU lation BUtton
 Press the air recirculation button to
recirculate air inside the vehicle.
 Press the air recirculation button again
to turn air recirculation off.
 The air recirculation mode cannot be selected if the air flow control dial is in the
defrost position .
05
04
03
02
01
06
07
08
09
FRONT-PASSENGER AIR BAG STATUS LIGHT
This vehicle is equipped with the Nissan Advanced Air
Bag system. Under some conditions, depending on
pressure detected on the passenger seat and how the
seat belt is used, the front-passenger air bag is designed
to automatically turn oFF. When the front-passenger air
bag is oFF , the front-passenger air bag status light will
illuminate*. For example:
 When the system detects that the front-passenger’s seat is occupied by a small
adult, child or child restraint as outlined in the Owner’s Manual, the
Pass
ai R Bag
oFF or will illuminate to indicate that the front-passenger air bag is oFF and will not inflate in a crash.
 When the front-passenger’s seat is occupied and the passenger meets the
conditions outlined in the Owner’s Manual, the
Pass
ai R Bag
oFF or will not illuminate to
indicate that the front-passenger air bag is operational.
*When the system detects that the front-passenger’s seat is unoccupied, the passenger air bag status light will not illuminate even though the front-passenger
air bag is oFF.
Refer to the Owner’s Manual for detailed information regarding the Nissan Advanced Air
Bag System.

02
03
04
07
01
06
05
QR6E-0V42U1 Printing: February 2006 (08)
Nissan, the Nissan Brand Symbol, “SHIFT_” tagline, Z and Nissan model names are Nissan trademarks.
©2006 Nissan North America, Inc.
HE ADLIGHT CONTROL
LIGHTS ON DEMAND
STEERING WHEEL
TILT ADJUSTMENT ( BEHIND STEERING WHEEL)
CRUISE CONTROL
WINDSHIELD WIPER/
WASHER CONTROL S
CLIMATE
CONTROLS
TIRE PRESSURE
MONITORING SYSTEM
TRIP BUT TON
OUTSIDE MIRROR CONTROL
STEERING WHEEL SWITCHES
FOR AUDIO CONTROL
DISPL AY SCREEN
AUDIO SYSTEM
Sh ift_
LIGHTS ON DEMAND
The
lights on demand switch allows the driver
to select one of three lighting modes for the interior
lights and puddle lamps (if so equipped): on, door, off.
Push the top portion of the switch and the
interior lights and puddle lamps will illuminate;
they will turn off automatically after 30 minutes,
to prevent the battery from becoming
discharged.
If the
lights on demand switch is in the neutral position, the lights will
stay on for about 30 seconds when:
 The doors are unlocked by the keyfob, a key, or the power door lock switch
while all doors are closed and the ignition switch is in the OFF position.
 The driver’s door is opened and then closed while the key is removed from the
ignition switch.
 The key is removed from the ignition switch while all doors are closed.
The interior lights and puddle lamps (if so equipped) will turn off while the

30-second timer is activated when:
 The driver’s door is locked by the keyfob, a key, or the power door lock switch.
 The ignition switch is turned on.
The lights will turn off automatically after 30 minutes while the doors are open to
prevent the battery from becoming discharged.
Push the bottom portion of the switch and the interior lights and puddle
lamps (if so equipped) will be turned off.
 The lights can be turned off so sleeping passengers are not disturbed when
the doors are opened.
 The lights on the front doors will turn on when the front doors are opened.
04
05TRIP BUTTON
When t R iP is pressed, the following modes will
display on the screen:
 TRIP 1 – TIME, DIST, AVG
 TRIP 2 – TIME, DIST, AVG
 OFF
TRIP 1 or TRIP 2 record journey time, trip odometer and average speed.
To reset TRIP 1 and TRIP 2, use the joystick to select R eset ; press ente R or
t R iP for approximately 2 seconds.
03
RE AR SONAR SWITCH
01
see K/tR aCK BU tton
To scan quickly through each broadcasting station, press the see K/tRa CK button.
The tuner will pause for 5 seconds on each broadcasting station. To skip from one
track to another on a CD, press the see K/tRa CK button. Each time the button is
pressed, the CD will advance or skip back one track.
t U ne /ReW/FF BU tton
To fast forward or rewind a track, press the ReW/FF button. The disc will play at

an altered speed until the button is released. To manually tune the radio, press the
tU ne button.
PR og /RP t BU tton
To change the play pattern of the CD, press the PRog /RPt button. To activate the
Radio Data System (RDS), press the PRog /RPt button. RDS provides information
about radio stations (type, call numbers, etc.)
PR eset a · B · C BU tton
Press PR eset a-B-C button until you reach the desired setting. The radio is

equipped with three separate banks of six station presets (18 total station presets).
You may store any combination of AM, FM or SAT* radio presets on each bank.
C d P la Y BU tton
To begin play, press the Cd button.
R ea R aV BU tton

To turn the rear audio controls on, press the ReaR aV button. Press again to turn
rear controller off. To turn on the DVD mode (if so equipped), press and hold the
R eaR aV button for 2 seconds.
s Pea KeR C ont Rol BU tton
To activate the rear headphones and turn off the rear speakers, press the SPEAKER
CONTROL button. To deactivate the rear headphones, press the button again.
t U ning and a U dio Cont Rol Kno B
To manually tune the radio, turn the tUne knob. Adjust the bass , treble, fade,

balance, and Speed Sensitive Volume (SSV) by pressing the aU dio knob until the
desired mode appears in the display. Then turn the tUne knob to adjust to the
desired level.
station and Cd sele Ct BU ttons
To store a station in a preset you must first select A, B, or C memory bank by pressing
the PR eset a·B·C button and tune to the desired AM, FM or SAT* station. Then

press the desired station select button for at least 2 seconds. When the preset
indicator illuminates, a beep will sound, indicating memorization is complete. To retrieve
a previously set station, select the memory bank where the preset was set, then press
the corresponding station select button.
AUDIO
SYSTEM
06
* SAT presets are only available on SAT equipped vehicles.
05
04
03
02
01
06
07
08
09
SEAT BELT WARNING LIGHT AND CHIME
 The light and chime remind you to fasten your seat
belts. The light illuminates whenever the ignition key
is turned to the ON or START position and remains
illuminated until the driver’s seat belt is fastened. At
the same time, the chime sounds for about 6 seconds
unless the driver’s seat belt is securely fastened.
 The seat belt warning light may also illuminate if the front passenger’s seat belt is
not fastened when the front passenger’s seat is occupied (if so equipped). For 5
seconds after the ignition switch is in the ON position, the system does not activate
the warning light for the front passenger.
Refer to the Owner’s Manual for detailed information regarding seat belt usage.

This easy-to-use Quick Reference Guide is intended to help you more fully appreciate
some of the unique features and functions of your new vehicle. However, it is not intended
to replace your Owner’s Manual. The Owner’s Manual contains more detailed information
to help you better understand the important safety warnings, features, operation, and
maintenance of your vehicle.
02STEERING WHEEL SWITCHES FOR
AUDIO CONTROL (if so equipped)
 To turn steering wheel audio system on,
push Po W eR
.
 Push the
mode button to change the mode in
the following sequence: Preset radio station bank

( A or B or C)
CD (if a CD is in the player)
SAT (if equipped) DVD (if equipped).
DVD will show in the display even if there is no DVD in the player.
 The < > switch can be used to perform the following:
• Push the
< >
switch
for less than 1.5 seconds to change to the preset station.
• Push the < > switch for more than 1.5 seconds to seek to the next
broadcasting radio station.
• Push the
< > switch while playing a CD for less than 1.5 seconds to change
programs on the CD.
• If the vehicle is equipped with a 6 Disc CD changer, push the
< > switch for
more than 1.5 seconds to change between CDs.
 Push the Vol control switch or to increase or decrease volume.
AD D ITIONAL FEATU R E S
TIRE PRESSURE MONITORING SYSTEM (TPMS)
This system monitors tire pressure. Please remember, this
system does not detect a sudden drop in tire pressure (for
example, a blowout while driving). It also does not monitor the
air pressure in the spare tire.
Tire pressure is affected by temperature. Low outside temperature causes lower
tire pressure. This may cause the low tire pressure warning light to illuminate.
If the low tire pressure warning light comes on, check the tire pressure in all four
tires. Adjust the low tire pressure to the recommended
COLD tire pressure shown
on the Tire and Loading Information label to turn the low tire pressure warning light
off .
If TPMS is not functioning properly, the low tire pressure warning light will flash for

approximately 60 seconds when the key is turned on. After 60 seconds, the light
will remain on. Have the system checked by a NISSAN dealer.
A UTOMATIC CLIMATE CONTROL (if so equipped)07
0201
05
0704
08
09
03
06
080607050302
01
09
04
CRUISE CONTROL
 To initiate cruise control, push on. (The CRU ise
indicator light will illuminate.)
 To set a cruising speed, accelerate to the desired
speed, push C oast /set and release. (The
set
indicator light will illuminate.)
 To set a faster or slower cruising speed:
• Press on the brake or accelerator to attain the desired speed, push
Coast/ set, and release.
• Push and hold the aCC el/R es switch to increase speed. Release the
switch when the vehicle attains the desired speed. Push and release the
aCC el/R es switch to increase speed by about 1 MPH.
• Push and hold the Coast/ set switch to decrease speed. Release the
switch when the vehicle attains the desired speed. Push and release the
Coast/ set switch to decrease speed by about 1 MPH.
 To resume a preset speed, push a CC el/R es and release.
 To cancel cruise control, push the C an Cel switch or tap the brake pedal. The
SET indicator light in the instrument panel will go out.
 To turn off cruise control, push the main ( on /o FF ) switch. Both the CRUISE
indicator light and the SET light in the instrument panel will go out. a
U to BU tton
 Press the aUto button
01. Turn the driver’s side temperature control dial 02
to the desired temperature. This will allow the fan speed, air flow distribution and
temperature to be automatically maintained.
 Press the aUto button a second time to turn the passenger’s side temperature
controls on or off. This will allow the passenger’s side temperature to be
adjusted independently from driver’s side control.
 When aUto is pressed, aUto will be displayed. When aUto is pressed a
second time, dUal will be displayed.
d RiV e R’ s side tem Pe R at UR e C ont Rol dial
Turn the driver’s temperature control dial left for cold air or right for hot air.
P assenge R’s side tem Pe R at UR e C ont Rol dial
Turn the passenger’s temperature control dial left for cold air or right for hot air.
ai R F loW mode Cont Rol BU tton
Press
mode button repeatedly to scroll through the following air flow outlets: Air flows from the center and side vents.
Air flows from the center, side, and foot vents.
Air flows mainly from the foot vents.
Air flows from the defroster and foot vents.
Air flows mainly from the defroster vents.
F an s Peed Cont Rol dial
Turn the fan speed control dial
to
the left (slower) or right (faster) to manually
control fan speed. Press aUto to automatically control fan speed.
de FRosting /de Fogging FRont and side Windo Ws
 Press the defroster control button to
turn the system on. The A/C
automatically turns on when the defroster mode is selected.
 Turn the driver’s side temperature control dial left or right to set the desired temperature.
 To set the defroster on high, turn the fan speed dial all the way to the right.
de FRosting /de Fogging Rea R W indo W and (if so equipped) oUtside
heated mi RR oR

Push the rear window defroster switch on.
Push the switch again to manually
turn the defroster off. This function automatically turns off in approximately 15
minutes.
a /C on /o FF BU tton
Press the a/C button to manually turn the A/C on or off.
ai R R eC iRCU lation BUtton
 Press the air recirculation button to
recirculate air inside the vehicle.
 Press the air recirculation button again
to turn air recirculation off.
 The air recirculation mode cannot be selected if the air flow control dial is in the
defrost position .
05
04
03
02
01
06
07
08
09
FRONT-PASSENGER AIR BAG STATUS LIGHT
This vehicle is equipped with the Nissan Advanced Air
Bag system. Under some conditions, depending on
pressure detected on the passenger seat and how the
seat belt is used, the front-passenger air bag is designed
to automatically turn oFF. When the front-passenger air
bag is oFF , the front-passenger air bag status light will
illuminate*. For example:
 When the system detects that the front-passenger’s seat is occupied by a small
adult, child or child restraint as outlined in the Owner’s Manual, the
Pass
ai R Bag
oFF or will illuminate to indicate that the front-passenger air bag is oFF and will not inflate in a crash.
 When the front-passenger’s seat is occupied and the passenger meets the
conditions outlined in the Owner’s Manual, the
Pass
ai R Bag
oFF or will not illuminate to
indicate that the front-passenger air bag is operational.
*When the system detects that the front-passenger’s seat is unoccupied, the passenger air bag status light will not illuminate even though the front-passenger
air bag is oFF.
Refer to the Owner’s Manual for detailed information regarding the Nissan Advanced Air
Bag System.

02
03
04
07
01
06
05
QR6E-0V42U1 Printing: February 2006 (08)
Nissan, the Nissan Brand Symbol, “SHIFT_” tagline, Z and Nissan model names are Nissan trademarks.
©2006 Nissan North America, Inc.
HE ADLIGHT CONTROL
LIGHTS ON DEMAND
STEERING WHEEL
TILT ADJUSTMENT ( BEHIND STEERING WHEEL)
CRUISE CONTROL
WINDSHIELD WIPER/
WASHER CONTROL S
CLIMATE
CONTROLS
TIRE PRESSURE
MONITORING SYSTEM
TRIP BUT TON
OUTSIDE MIRROR CONTROL
STEERING WHEEL SWITCHES
FOR AUDIO CONTROL
DISPL AY SCREEN
AUDIO SYSTEM
Sh ift_
LIGHTS ON DEMAND
The
lights on demand switch allows the driver
to select one of three lighting modes for the interior
lights and puddle lamps (if so equipped): on, door, off.
Push the top portion of the switch and the
interior lights and puddle lamps will illuminate;
they will turn off automatically after 30 minutes,
to prevent the battery from becoming
discharged.
If the
lights on demand switch is in the neutral position, the lights will
stay on for about 30 seconds when:
 The doors are unlocked by the keyfob, a key, or the power door lock switch
while all doors are closed and the ignition switch is in the OFF position.
 The driver’s door is opened and then closed while the key is removed from the
ignition switch.
 The key is removed from the ignition switch while all doors are closed.
The interior lights and puddle lamps (if so equipped) will turn off while the

30-second timer is activated when:
 The driver’s door is locked by the keyfob, a key, or the power door lock switch.
 The ignition switch is turned on.
The lights will turn off automatically after 30 minutes while the doors are open to
prevent the battery from becoming discharged.
Push the bottom portion of the switch and the interior lights and puddle
lamps (if so equipped) will be turned off.
 The lights can be turned off so sleeping passengers are not disturbed when
the doors are opened.
 The lights on the front doors will turn on when the front doors are opened.
04
05TRIP BUTTON
When t R iP is pressed, the following modes will
display on the screen:
 TRIP 1 – TIME, DIST, AVG
 TRIP 2 – TIME, DIST, AVG
 OFF
TRIP 1 or TRIP 2 record journey time, trip odometer and average speed.
To reset TRIP 1 and TRIP 2, use the joystick to select R eset ; press ente R or
t R iP for approximately 2 seconds.
03
RE AR SONAR SWITCH
01
see K/tR aCK BU tton
To scan quickly through each broadcasting station, press the see K/tRa CK button.
The tuner will pause for 5 seconds on each broadcasting station. To skip from one
track to another on a CD, press the see K/tRa CK button. Each time the button is
pressed, the CD will advance or skip back one track.
t U ne /ReW/FF BU tton
To fast forward or rewind a track, press the ReW/FF button. The disc will play at

an altered speed until the button is released. To manually tune the radio, press the
tU ne button.
PR og /RP t BU tton
To change the play pattern of the CD, press the PRog /RPt button. To activate the
Radio Data System (RDS), press the PRog /RPt button. RDS provides information
about radio stations (type, call numbers, etc.)
PR eset a · B · C BU tton
Press PR eset a-B-C button until you reach the desired setting. The radio is

equipped with three separate banks of six station presets (18 total station presets).
You may store any combination of AM, FM or SAT* radio presets on each bank.
C d P la Y BU tton
To begin play, press the Cd button.
R ea R aV BU tton

To turn the rear audio controls on, press the ReaR aV button. Press again to turn
rear controller off. To turn on the DVD mode (if so equipped), press and hold the
R eaR aV button for 2 seconds.
s Pea KeR C ont Rol BU tton
To activate the rear headphones and turn off the rear speakers, press the SPEAKER
CONTROL button. To deactivate the rear headphones, press the button again.
t U ning and a U dio Cont Rol Kno B
To manually tune the radio, turn the tUne knob. Adjust the bass , treble, fade,

balance, and Speed Sensitive Volume (SSV) by pressing the aU dio knob until the
desired mode appears in the display. Then turn the tUne knob to adjust to the
desired level.
station and Cd sele Ct BU ttons
To store a station in a preset you must first select A, B, or C memory bank by pressing
the PR eset a·B·C button and tune to the desired AM, FM or SAT* station. Then

press the desired station select button for at least 2 seconds. When the preset
indicator illuminates, a beep will sound, indicating memorization is complete. To retrieve
a previously set station, select the memory bank where the preset was set, then press
the corresponding station select button.
AUDIO
SYSTEM
06
* SAT presets are only available on SAT equipped vehicles.
05
04
03
02
01
06
07
08
09
SEAT BELT WARNING LIGHT AND CHIME
 The light and chime remind you to fasten your seat
belts. The light illuminates whenever the ignition key
is turned to the ON or START position and remains
illuminated until the driver’s seat belt is fastened. At
the same time, the chime sounds for about 6 seconds
unless the driver’s seat belt is securely fastened.
 The seat belt warning light may also illuminate if the front passenger’s seat belt is
not fastened when the front passenger’s seat is occupied (if so equipped). For 5
seconds after the ignition switch is in the ON position, the system does not activate
the warning light for the front passenger.
Refer to the Owner’s Manual for detailed information regarding seat belt usage.

This easy-to-use Quick Reference Guide is intended to help you more fully appreciate
some of the unique features and functions of your new vehicle. However, it is not intended
to replace your Owner’s Manual. The Owner’s Manual contains more detailed information
to help you better understand the important safety warnings, features, operation, and
maintenance of your vehicle.
02STEERING WHEEL SWITCHES FOR
AUDIO CONTROL (if so equipped)
 To turn steering wheel audio system on,
push Po W eR
.
 Push the
mode button to change the mode in
the following sequence: Preset radio station bank

( A or B or C)
CD (if a CD is in the player)
SAT (if equipped) DVD (if equipped).
DVD will show in the display even if there is no DVD in the player.
 The < > switch can be used to perform the following:
• Push the
< >
switch
for less than 1.5 seconds to change to the preset station.
• Push the < > switch for more than 1.5 seconds to seek to the next
broadcasting radio station.
• Push the
< > switch while playing a CD for less than 1.5 seconds to change
programs on the CD.
• If the vehicle is equipped with a 6 Disc CD changer, push the
< > switch for
more than 1.5 seconds to change between CDs.
 Push the Vol control switch or to increase or decrease volume.
AD D ITIONAL FEATU R E S
TIRE PRESSURE MONITORING SYSTEM (TPMS)
This system monitors tire pressure. Please remember, this
system does not detect a sudden drop in tire pressure (for
example, a blowout while driving). It also does not monitor the
air pressure in the spare tire.
Tire pressure is affected by temperature. Low outside temperature causes lower
tire pressure. This may cause the low tire pressure warning light to illuminate.
If the low tire pressure warning light comes on, check the tire pressure in all four
tires. Adjust the low tire pressure to the recommended
COLD tire pressure shown
on the Tire and Loading Information label to turn the low tire pressure warning light
off .
If TPMS is not functioning properly, the low tire pressure warning light will flash for

approximately 60 seconds when the key is turned on. After 60 seconds, the light
will remain on. Have the system checked by a NISSAN dealer.
A UTOMATIC CLIMATE CONTROL (if so equipped)07
0201
05
0704
08
09
03
06
080607050302
01
09
04
CRUISE CONTROL
 To initiate cruise control, push on. (The CRU ise
indicator light will illuminate.)
 To set a cruising speed, accelerate to the desired
speed, push C oast /set and release. (The
set
indicator light will illuminate.)
 To set a faster or slower cruising speed:
• Press on the brake or accelerator to attain the desired speed, push
Coast/ set, and release.
• Push and hold the aCC el/R es switch to increase speed. Release the
switch when the vehicle attains the desired speed. Push and release the
aCC el/R es switch to increase speed by about 1 MPH.
• Push and hold the Coast/ set switch to decrease speed. Release the
switch when the vehicle attains the desired speed. Push and release the
Coast/ set switch to decrease speed by about 1 MPH.
 To resume a preset speed, push a CC el/R es and release.
 To cancel cruise control, push the C an Cel switch or tap the brake pedal. The
SET indicator light in the instrument panel will go out.
 To turn off cruise control, push the main ( on /o FF ) switch. Both the CRUISE
indicator light and the SET light in the instrument panel will go out. a
U to BU tton
 Press the aUto button
01. Turn the driver’s side temperature control dial 02
to the desired temperature. This will allow the fan speed, air flow distribution and
temperature to be automatically maintained.
 Press the aUto button a second time to turn the passenger’s side temperature
controls on or off. This will allow the passenger’s side temperature to be
adjusted independently from driver’s side control.
 When aUto is pressed, aUto will be displayed. When aUto is pressed a
second time, dUal will be displayed.
d RiV e R’ s side tem Pe R at UR e C ont Rol dial
Turn the driver’s temperature control dial left for cold air or right for hot air.
P assenge R’s side tem Pe R at UR e C ont Rol dial
Turn the passenger’s temperature control dial left for cold air or right for hot air.
ai R F loW mode Cont Rol BU tton
Press
mode button repeatedly to scroll through the following air flow outlets: Air flows from the center and side vents.
Air flows from the center, side, and foot vents.
Air flows mainly from the foot vents.
Air flows from the defroster and foot vents.
Air flows mainly from the defroster vents.
F an s Peed Cont Rol dial
Turn the fan speed control dial
to
the left (slower) or right (faster) to manually
control fan speed. Press aUto to automatically control fan speed.
de FRosting /de Fogging FRont and side Windo Ws
 Press the defroster control button to
turn the system on. The A/C
automatically turns on when the defroster mode is selected.
 Turn the driver’s side temperature control dial left or right to set the desired temperature.
 To set the defroster on high, turn the fan speed dial all the way to the right.
de FRosting /de Fogging Rea R W indo W and (if so equipped) oUtside
heated mi RR oR

Push the rear window defroster switch on.
Push the switch again to manually
turn the defroster off. This function automatically turns off in approximately 15
minutes.
a /C on /o FF BU tton
Press the a/C button to manually turn the A/C on or off.
ai R R eC iRCU lation BUtton
 Press the air recirculation button to
recirculate air inside the vehicle.
 Press the air recirculation button again
to turn air recirculation off.
 The air recirculation mode cannot be selected if the air flow control dial is in the
defrost position .
05
04
03
02
01
06
07
08
09
FRONT-PASSENGER AIR BAG STATUS LIGHT
This vehicle is equipped with the Nissan Advanced Air
Bag system. Under some conditions, depending on
pressure detected on the passenger seat and how the
seat belt is used, the front-passenger air bag is designed
to automatically turn oFF. When the front-passenger air
bag is oFF , the front-passenger air bag status light will
illuminate*. For example:
 When the system detects that the front-passenger’s seat is occupied by a small
adult, child or child restraint as outlined in the Owner’s Manual, the
Pass
ai R Bag
oFF or will illuminate to indicate that the front-passenger air bag is oFF and will not inflate in a crash.
 When the front-passenger’s seat is occupied and the passenger meets the
conditions outlined in the Owner’s Manual, the
Pass
ai R Bag
oFF or will not illuminate to
indicate that the front-passenger air bag is operational.
*When the system detects that the front-passenger’s seat is unoccupied, the passenger air bag status light will not illuminate even though the front-passenger
air bag is oFF.
Refer to the Owner’s Manual for detailed information regarding the Nissan Advanced Air
Bag System.

02
03
04
07
01
06
05
QR6E-0V42U1 Printing: February 2006 (08)
Nissan, the Nissan Brand Symbol, “SHIFT_” tagline, Z and Nissan model names are Nissan trademarks.
©2006 Nissan North America, Inc.
HE ADLIGHT CONTROL
LIGHTS ON DEMAND
STEERING WHEEL
TILT ADJUSTMENT ( BEHIND STEERING WHEEL)
CRUISE CONTROL
WINDSHIELD WIPER/
WASHER CONTROL S
CLIMATE
CONTROLS
TIRE PRESSURE
MONITORING SYSTEM
TRIP BUT TON
OUTSIDE MIRROR CONTROL
STEERING WHEEL SWITCHES
FOR AUDIO CONTROL
DISPL AY SCREEN
AUDIO SYSTEM
Sh ift_
LIGHTS ON DEMAND
The
lights on demand switch allows the driver
to select one of three lighting modes for the interior
lights and puddle lamps (if so equipped): on, door, off.
Push the top portion of the switch and the
interior lights and puddle lamps will illuminate;
they will turn off automatically after 30 minutes,
to prevent the battery from becoming
discharged.
If the
lights on demand switch is in the neutral position, the lights will
stay on for about 30 seconds when:
 The doors are unlocked by the keyfob, a key, or the power door lock switch
while all doors are closed and the ignition switch is in the OFF position.
 The driver’s door is opened and then closed while the key is removed from the
ignition switch.
 The key is removed from the ignition switch while all doors are closed.
The interior lights and puddle lamps (if so equipped) will turn off while the

30-second timer is activated when:
 The driver’s door is locked by the keyfob, a key, or the power door lock switch.
 The ignition switch is turned on.
The lights will turn off automatically after 30 minutes while the doors are open to
prevent the battery from becoming discharged.
Push the bottom portion of the switch and the interior lights and puddle
lamps (if so equipped) will be turned off.
 The lights can be turned off so sleeping passengers are not disturbed when
the doors are opened.
 The lights on the front doors will turn on when the front doors are opened.
04
05TRIP BUTTON
When t R iP is pressed, the following modes will
display on the screen:
 TRIP 1 – TIME, DIST, AVG
 TRIP 2 – TIME, DIST, AVG
 OFF
TRIP 1 or TRIP 2 record journey time, trip odometer and average speed.
To reset TRIP 1 and TRIP 2, use the joystick to select R eset ; press ente R or
t R iP for approximately 2 seconds.
03
RE AR SONAR SWITCH
01
see K/tR aCK BU tton
To scan quickly through each broadcasting station, press the see K/tRa CK button.
The tuner will pause for 5 seconds on each broadcasting station. To skip from one
track to another on a CD, press the see K/tRa CK button. Each time the button is
pressed, the CD will advance or skip back one track.
t U ne /ReW/FF BU tton
To fast forward or rewind a track, press the ReW/FF button. The disc will play at

an altered speed until the button is released. To manually tune the radio, press the
tU ne button.
PR og /RP t BU tton
To change the play pattern of the CD, press the PRog /RPt button. To activate the
Radio Data System (RDS), press the PRog /RPt button. RDS provides information
about radio stations (type, call numbers, etc.)
PR eset a · B · C BU tton
Press PR eset a-B-C button until you reach the desired setting. The radio is

equipped with three separate banks of six station presets (18 total station presets).
You may store any combination of AM, FM or SAT* radio presets on each bank.
C d P la Y BU tton
To begin play, press the Cd button.
R ea R aV BU tton

To turn the rear audio controls on, press the ReaR aV button. Press again to turn
rear controller off. To turn on the DVD mode (if so equipped), press and hold the
R eaR aV button for 2 seconds.
s Pea KeR C ont Rol BU tton
To activate the rear headphones and turn off the rear speakers, press the SPEAKER
CONTROL button. To deactivate the rear headphones, press the button again.
t U ning and a U dio Cont Rol Kno B
To manually tune the radio, turn the tUne knob. Adjust the bass , treble, fade,

balance, and Speed Sensitive Volume (SSV) by pressing the aU dio knob until the
desired mode appears in the display. Then turn the tUne knob to adjust to the
desired level.
station and Cd sele Ct BU ttons
To store a station in a preset you must first select A, B, or C memory bank by pressing
the PR eset a·B·C button and tune to the desired AM, FM or SAT* station. Then

press the desired station select button for at least 2 seconds. When the preset
indicator illuminates, a beep will sound, indicating memorization is complete. To retrieve
a previously set station, select the memory bank where the preset was set, then press
the corresponding station select button.
AUDIO
SYSTEM
06
* SAT presets are only available on SAT equipped vehicles.
05
04
03
02
01
06
07
08
09
SEAT BELT WARNING LIGHT AND CHIME
 The light and chime remind you to fasten your seat
belts. The light illuminates whenever the ignition key
is turned to the ON or START position and remains
illuminated until the driver’s seat belt is fastened. At
the same time, the chime sounds for about 6 seconds
unless the driver’s seat belt is securely fastened.
 The seat belt warning light may also illuminate if the front passenger’s seat belt is
not fastened when the front passenger’s seat is occupied (if so equipped). For 5
seconds after the ignition switch is in the ON position, the system does not activate
the warning light for the front passenger.
Refer to the Owner’s Manual for detailed information regarding seat belt usage.

This easy-to-use Quick Reference Guide is intended to help you more fully appreciate
some of the unique features and functions of your new vehicle. However, it is not intended
to replace your Owner’s Manual. The Owner’s Manual contains more detailed information
to help you better understand the important safety warnings, features, operation, and
maintenance of your vehicle.
02STEERING WHEEL SWITCHES FOR
AUDIO CONTROL (if so equipped)
 To turn steering wheel audio system on,
push Po W eR
.
 Push the
mode button to change the mode in
the following sequence: Preset radio station bank

( A or B or C)
CD (if a CD is in the player)
SAT (if equipped) DVD (if equipped).
DVD will show in the display even if there is no DVD in the player.
 The < > switch can be used to perform the following:
• Push the
< >
switch
for less than 1.5 seconds to change to the preset station.
• Push the < > switch for more than 1.5 seconds to seek to the next
broadcasting radio station.
• Push the
< > switch while playing a CD for less than 1.5 seconds to change
programs on the CD.
• If the vehicle is equipped with a 6 Disc CD changer, push the
< > switch for
more than 1.5 seconds to change between CDs.
 Push the Vol control switch or to increase or decrease volume.
AD D ITIONAL FEATU R E S
TIRE PRESSURE MONITORING SYSTEM (TPMS)
This system monitors tire pressure. Please remember, this
system does not detect a sudden drop in tire pressure (for
example, a blowout while driving). It also does not monitor the
air pressure in the spare tire.
Tire pressure is affected by temperature. Low outside temperature causes lower
tire pressure. This may cause the low tire pressure warning light to illuminate.
If the low tire pressure warning light comes on, check the tire pressure in all four
tires. Adjust the low tire pressure to the recommended
COLD tire pressure shown
on the Tire and Loading Information label to turn the low tire pressure warning light
off .
If TPMS is not functioning properly, the low tire pressure warning light will flash for

approximately 60 seconds when the key is turned on. After 60 seconds, the light
will remain on. Have the system checked by a NISSAN dealer.
A UTOMATIC CLIMATE CONTROL (if so equipped)07
0201
05
0704
08
09
03
06
080607050302
01
09
04
CRUISE CONTROL
 To initiate cruise control, push on. (The CRU ise
indicator light will illuminate.)
 To set a cruising speed, accelerate to the desired
speed, push C oast /set and release. (The
set
indicator light will illuminate.)
 To set a faster or slower cruising speed:
• Press on the brake or accelerator to attain the desired speed, push
Coast/ set, and release.
• Push and hold the aCC el/R es switch to increase speed. Release the
switch when the vehicle attains the desired speed. Push and release the
aCC el/R es switch to increase speed by about 1 MPH.
• Push and hold the Coast/ set switch to decrease speed. Release the
switch when the vehicle attains the desired speed. Push and release the
Coast/ set switch to decrease speed by about 1 MPH.
 To resume a preset speed, push a CC el/R es and release.
 To cancel cruise control, push the C an Cel switch or tap the brake pedal. The
SET indicator light in the instrument panel will go out.
 To turn off cruise control, push the main ( on /o FF ) switch. Both the CRUISE
indicator light and the SET light in the instrument panel will go out. a
U to BU tton
 Press the aUto button
01. Turn the driver’s side temperature control dial 02
to the desired temperature. This will allow the fan speed, air flow distribution and
temperature to be automatically maintained.
 Press the aUto button a second time to turn the passenger’s side temperature
controls on or off. This will allow the passenger’s side temperature to be
adjusted independently from driver’s side control.
 When aUto is pressed, aUto will be displayed. When aUto is pressed a
second time, dUal will be displayed.
d RiV e R’ s side tem Pe R at UR e C ont Rol dial
Turn the driver’s temperature control dial left for cold air or right for hot air.
P assenge R’s side tem Pe R at UR e C ont Rol dial
Turn the passenger’s temperature control dial left for cold air or right for hot air.
ai R F loW mode Cont Rol BU tton
Press
mode button repeatedly to scroll through the following air flow outlets: Air flows from the center and side vents.
Air flows from the center, side, and foot vents.
Air flows mainly from the foot vents.
Air flows from the defroster and foot vents.
Air flows mainly from the defroster vents.
F an s Peed Cont Rol dial
Turn the fan speed control dial
to
the left (slower) or right (faster) to manually
control fan speed. Press aUto to automatically control fan speed.
de FRosting /de Fogging FRont and side Windo Ws
 Press the defroster control button to
turn the system on. The A/C
automatically turns on when the defroster mode is selected.
 Turn the driver’s side temperature control dial left or right to set the desired temperature.
 To set the defroster on high, turn the fan speed dial all the way to the right.
de FRosting /de Fogging Rea R W indo W and (if so equipped) oUtside
heated mi RR oR

Push the rear window defroster switch on.
Push the switch again to manually
turn the defroster off. This function automatically turns off in approximately 15
minutes.
a /C on /o FF BU tton
Press the a/C button to manually turn the A/C on or off.
ai R R eC iRCU lation BUtton
 Press the air recirculation button to
recirculate air inside the vehicle.
 Press the air recirculation button again
to turn air recirculation off.
 The air recirculation mode cannot be selected if the air flow control dial is in the
defrost position .
05
04
03
02
01
06
07
08
09
FRONT-PASSENGER AIR BAG STATUS LIGHT
This vehicle is equipped with the Nissan Advanced Air
Bag system. Under some conditions, depending on
pressure detected on the passenger seat and how the
seat belt is used, the front-passenger air bag is designed
to automatically turn oFF. When the front-passenger air
bag is oFF , the front-passenger air bag status light will
illuminate*. For example:
 When the system detects that the front-passenger’s seat is occupied by a small
adult, child or child restraint as outlined in the Owner’s Manual, the
Pass
ai R Bag
oFF or will illuminate to indicate that the front-passenger air bag is oFF and will not inflate in a crash.
 When the front-passenger’s seat is occupied and the passenger meets the
conditions outlined in the Owner’s Manual, the
Pass
ai R Bag
oFF or will not illuminate to
indicate that the front-passenger air bag is operational.
*When the system detects that the front-passenger’s seat is unoccupied, the passenger air bag status light will not illuminate even though the front-passenger
air bag is oFF.
Refer to the Owner’s Manual for detailed information regarding the Nissan Advanced Air
Bag System.

SUNROOF CONTROLS (if so equipped)
 To tilt the sunroof up, press UP. (If the roof is already
open, it will close before tilting up.) To tilt the sunroof
down, press doWn
.
 To open partially, slide the switch toward oPen. (If the
roof is tilted up, it will automatically tilt down before
opening.) To open fully, slide the switch completely to
oP en
.
 To close partially, slide the switch toward Close . To
close fully, slide the switch completely to Close .
CHILD SAFET Y DOOR LOCK
Child safety locks help prevent the sliding doors from being
opened accidentally, especially when small children are in
the vehicle. The child safety lock levers are located on the
edge of the sliding doors. When the lever is in the loCK

position, the door can be opened only from the outside, with
the overhead console switch or the keyfob.
POWER SLIDING DOORS AND POWER BACK DOOR (if so equipped)
POWER SLIDING DOORS
The power sliding doors can be
activated by the buttons on the keyfob, the overhead console, and the door pillars.
 To open, close or reverse a sliding door, the ignition switch must be off or the
automatic transmission selector lever must be in Park.
 To open, close or reverse a sliding door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To activate a sliding door with the button on the door pillar, the main on /o FF switch
must be on, the door must be unlocked, and the child safety door lock must be in the
unlock position.
 To activate the power assist feature, manually move a sliding door toward the open
or close position using the inside or outside handle. The power assist feature will
automatically complete the motion.
P OWER BACK DOOR
The power back door can be activated by the buttons on the keyfob, the overhead
console, and the rear door pillar.
 To open, close or reverse the back door, the automatic transmission lever must be
in Park.
 To open, close or reverse the back door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To close the back door with the rear door pillar button, the main on/oFF switch
must be on.
The power sliding doors and the power back door have an anti-pinch safety feature.
Please refer to your Owner’s Manual for more information regarding this feature.
AUTOMATIC DRIVER POSITIONER (if so equipped)
The automatic driver positioner system has two features:
 Memory storage function
 Entry/exit function
MEMORY STOR AGE FUNCTION
Two positions for the driver’s seat, accelerator and brake
pedals, and outside mirrors can be stored in the automatic driver positioner memory.
Follow these procedures to set driver preferences.
SET THE DESIRED POSITIONING
1. Set the automatic transmission lever to the Park position.
2. Turn the ignition on and adjust the driver’s seat, accelerator and brake pedals, and
outside mirrors to the desired positions.
3. Press the
set (memory) button and within 5 seconds press the position button (1 or 2 ) for at least 1 second until the indicator light illuminates. The position is now
stored in memory.
LINK TO KEYFOB
 Within 5 seconds of setting the memory position (indicator light is on and ignition is
on), press the
button
on the remote.
 A keyfob can be linked to each memory button.
 If memory positioning is re-set to a new location, the keyfob automatically re-links.
RECALLING A MEMORY SET TING FROM THE MEMORY PAD
 With the automatic transmission lever in the Park position, press the position button (1 or 2 ) for at least 1 second.
FROM THE KEYFOB
 If properly linked, operation of the button
will automatically return the driver’s
seat, accelerator and brake pedals, and mirrors to the memorized position.
ENTRY/ EXIT FUNCTION
The driver’s seat moves to allow the driver to get into and out of the driver’s seat more
easily. The driver’s seat slides backward when:
 The key is removed from the ignition switch.
 The driver’s door is opened with the key turned to LOCK.
 The key is turned from ACC to LOCK with the driver’s door open and the automatic
transmission lever is in the Park position.
The driver’s seat returns to the previous position when:
 The key is inserted into the ignition switch.
 The driver’s door is closed with the key turned to LOCK.
 The key is turned from ACC to ON while the automatic transmission lever is in the
Park position.
REAR SONAR SYSTEM OFF SWITCH (if so equipped)
When backing up, this system will beep to alert you to obstacles
within 6 ft. of the rear bumper. The system beeps faster as the vehicle
gets closer to the obstacle. A continuous tone sounds when an
obstacle is less than 10 inches away from the bumper. Turn the system
off by pushing the rear sonar system
oFF switch. The system will
automatically reset the next time the ignition switch is turned on.
ADJUSTABLE A CCELERATOR AND BRAKE P EDALS (if so equipped)
The accelerator and brake pedals can be adjusted for your
driving comfort.
 Adjust the pedals when the automatic transmission lever
is in Park.
 Push to
move the position of the pedals forward. 01
 Push to
move the position of the pedals backward. 02
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
 Pull up on the lever under the front of the seat and
slide backward or forward; release.
01
 Lift the lever on the side of the seat to adjust your
seatback backward or forward; release when you
have found a comfortable angle and the seat belt
fits properly.
02
 Use the dials at the side of the driver’s seat to
adjust the angle and height of the seat

cushion.
03
With power seats (if so equipped):
 Move the control forward or backward to adjust
the seat cushion forward or backward.
04
 Pull up to raise the driver’s seat cushion; press
down to lower the cushion.
04
 Push the switch forward to move the seatback
forward; press it back to move the seatback
backward.
05
Your driver’s seat has a lumbar support; adjust it by
moving the lever forward or backward.
06
to fold the 3rd row bench seat flat into the floor for maximum cargo hauling:
 Remove all 3 head restraints. Remove the head restraints by lifting up, then press
and hold the release button and continue lifting and place the head restraints in the
storage bag.
 Disconnect and secure the center seat belt and tongues into the retractor base.
Then, press the button on the seatback while pulling back on the strap to release the
back of the seat.
01
 Rotate the seatback toward the back of the vehicle. 02
 Pull up on the lever located on the back of the seat base. This will fold the seat base
toward the back of the vehicle.
03
 The entire seat will rotate toward you and stow flat in the floor. 04
 Reverse this process to return the bench seat to a seating position. Make sure to
properly install the head restraints, reattach the center seat belt, press the bench
seat down into the floor, and pull back on the seatback until it latches into place.
Sh ift_convention
to move the 2nd row seats forward or backward:
 Pull the lever up and hold it while you slide the seat forward or backward to the
desired position.
01
 Release the lever to lock the seat in position.
t o recline the 2nd row seatbacks:
 Pull the lever up and lean forward or back. 02
the 2nd row seats can be tipped forward for easy entry or exit from the 3rd row seat:
 To enter the 3rd row seats, lift up on the lever located on the lower base of the seat;
this tips the seat forward.
03
 To exit the 3rd row seats, pull back on the lever on the lower base of the seat and
push the seat forward.
t o fold the 2nd row seats flat to the floor for maximum cargo hauling:
 Remove the head restraints by lifting up each head restraint. Then, press and hold
the release button and place the head restraints in the storage bag.
 Lift up on the recline lever to fold the seatback down on the seat base. 04
 Press down on the small lever on the back of the seat to release the base of
the seat.
05
 Then fold the entire seat forward into the stowed position on the floor. 06
 Reverse this process to return the 2nd row seats to a seating position. Make sure to
properly install the head restraints and to press the seats down to the floor until they
latch into place.
ADJUSTING AND FOLDING THE 2ND ROW SEAT
01
02
FOLDING THE 3RD ROW SEAT
lo CK doo Rs
Make sure all doors and windows are closed and
press the LOCK button to secure the vehicle.
U nlo CK doo Rs
Press the UNLOCK button once to unlock the
driver’s door. Press the UNLOCK button twice
within 5 seconds to unlock all doors.
P o W eR sliding doo Rs
Press and hold the POWER SLIDING DOOR
button (if so equipped) for longer than 0.5
seconds to open or close the power sliding
door. The door will reverse direction immediately
during power open or power close if the keyfob
button is pressed. A chime will sound to indicate
the reversal.
P o W eR B aCK doo R
Press and hold the POWER BACK DOOR button (if so equipped) for longer
than 0.5 seconds to open or close the power back door. The hazard lights
will flash and a chime will sound to indicate that the power open or power
close sequence has started. If you press the button again, the door will
reverse direction immediately; a chime will sound to indicate the reversal.
R emote o Pening o F FR ont Windo Ws
Press the UNLOCK button longer than 3 seconds to open the windows. (The keyfob

is not able to close the windows after opening them.)
REMOTE KEYLESS ENTRY SYSTEM
01
02
03
04
05
06
01
0203
04
05
06
01
02
03
04
FUEL FILLER LID RELEASE
To open, press the fuel filler lid release located on the
driver’s door. To lock, securely close the fuel filler lid.

The driver’s side power sliding door is disabled when the
fuel lid is open. The sliding door can be partially opened
manually.
DOOR LOCK SWITCH
The door lock switch is located on the driver’s door armrest. Push top
of switch
01 to lock all the doors. Push bottom of the switch 02 to
unlock all the doors.
2006
QU EST

Q U I C K R E F E R E N C E G U I D E

REAR VIEW MONITOR
(if so equipped)
When the automatic transmission lever is moved to the R
(Reverse) position, the monitor display will automatically
change to show the area behind the vehicle.
The colored lines on the display screen indicate approximate
distances to objects.
 Red 1.5 feet  Yellow 3 feet  Green 7 and 10 feet
01
02

SUNROOF CONTROLS (if so equipped)
 To tilt the sunroof up, press UP. (If the roof is already
open, it will close before tilting up.) To tilt the sunroof
down, press doWn
.
 To open partially, slide the switch toward oPen. (If the
roof is tilted up, it will automatically tilt down before
opening.) To open fully, slide the switch completely to
oP en
.
 To close partially, slide the switch toward Close . To
close fully, slide the switch completely to Close .
CHILD SAFET Y DOOR LOCK
Child safety locks help prevent the sliding doors from being
opened accidentally, especially when small children are in
the vehicle. The child safety lock levers are located on the
edge of the sliding doors. When the lever is in the loCK

position, the door can be opened only from the outside, with
the overhead console switch or the keyfob.
POWER SLIDING DOORS AND POWER BACK DOOR (if so equipped)
POWER SLIDING DOORS
The power sliding doors can be
activated by the buttons on the keyfob, the overhead console, and the door pillars.
 To open, close or reverse a sliding door, the ignition switch must be off or the
automatic transmission selector lever must be in Park.
 To open, close or reverse a sliding door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To activate a sliding door with the button on the door pillar, the main on /o FF switch
must be on, the door must be unlocked, and the child safety door lock must be in the
unlock position.
 To activate the power assist feature, manually move a sliding door toward the open
or close position using the inside or outside handle. The power assist feature will
automatically complete the motion.
P OWER BACK DOOR
The power back door can be activated by the buttons on the keyfob, the overhead
console, and the rear door pillar.
 To open, close or reverse the back door, the automatic transmission lever must be
in Park.
 To open, close or reverse the back door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To close the back door with the rear door pillar button, the main on/oFF switch
must be on.
The power sliding doors and the power back door have an anti-pinch safety feature.
Please refer to your Owner’s Manual for more information regarding this feature.
AUTOMATIC DRIVER POSITIONER (if so equipped)
The automatic driver positioner system has two features:
 Memory storage function
 Entry/exit function
MEMORY STOR AGE FUNCTION
Two positions for the driver’s seat, accelerator and brake
pedals, and outside mirrors can be stored in the automatic driver positioner memory.
Follow these procedures to set driver preferences.
SET THE DESIRED POSITIONING
1. Set the automatic transmission lever to the Park position.
2. Turn the ignition on and adjust the driver’s seat, accelerator and brake pedals, and
outside mirrors to the desired positions.
3. Press the
set (memory) button and within 5 seconds press the position button (1 or 2 ) for at least 1 second until the indicator light illuminates. The position is now
stored in memory.
LINK TO KEYFOB
 Within 5 seconds of setting the memory position (indicator light is on and ignition is
on), press the
button
on the remote.
 A keyfob can be linked to each memory button.
 If memory positioning is re-set to a new location, the keyfob automatically re-links.
RECALLING A MEMORY SET TING FROM THE MEMORY PAD
 With the automatic transmission lever in the Park position, press the position button (1 or 2 ) for at least 1 second.
FROM THE KEYFOB
 If properly linked, operation of the button
will automatically return the driver’s
seat, accelerator and brake pedals, and mirrors to the memorized position.
ENTRY/ EXIT FUNCTION
The driver’s seat moves to allow the driver to get into and out of the driver’s seat more
easily. The driver’s seat slides backward when:
 The key is removed from the ignition switch.
 The driver’s door is opened with the key turned to LOCK.
 The key is turned from ACC to LOCK with the driver’s door open and the automatic
transmission lever is in the Park position.
The driver’s seat returns to the previous position when:
 The key is inserted into the ignition switch.
 The driver’s door is closed with the key turned to LOCK.
 The key is turned from ACC to ON while the automatic transmission lever is in the
Park position.
REAR SONAR SYSTEM OFF SWITCH (if so equipped)
When backing up, this system will beep to alert you to obstacles
within 6 ft. of the rear bumper. The system beeps faster as the vehicle
gets closer to the obstacle. A continuous tone sounds when an
obstacle is less than 10 inches away from the bumper. Turn the system
off by pushing the rear sonar system
oFF switch. The system will
automatically reset the next time the ignition switch is turned on.
ADJUSTABLE A CCELERATOR AND BRAKE P EDALS (if so equipped)
The accelerator and brake pedals can be adjusted for your
driving comfort.
 Adjust the pedals when the automatic transmission lever
is in Park.
 Push to
move the position of the pedals forward. 01
 Push to
move the position of the pedals backward. 02
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
 Pull up on the lever under the front of the seat and
slide backward or forward; release.
01
 Lift the lever on the side of the seat to adjust your
seatback backward or forward; release when you
have found a comfortable angle and the seat belt
fits properly.
02
 Use the dials at the side of the driver’s seat to
adjust the angle and height of the seat

cushion.
03
With power seats (if so equipped):
 Move the control forward or backward to adjust
the seat cushion forward or backward.
04
 Pull up to raise the driver’s seat cushion; press
down to lower the cushion.
04
 Push the switch forward to move the seatback
forward; press it back to move the seatback
backward.
05
Your driver’s seat has a lumbar support; adjust it by
moving the lever forward or backward.
06
to fold the 3rd row bench seat flat into the floor for maximum cargo hauling:
 Remove all 3 head restraints. Remove the head restraints by lifting up, then press
and hold the release button and continue lifting and place the head restraints in the
storage bag.
 Disconnect and secure the center seat belt and tongues into the retractor base.
Then, press the button on the seatback while pulling back on the strap to release the
back of the seat.
01
 Rotate the seatback toward the back of the vehicle. 02
 Pull up on the lever located on the back of the seat base. This will fold the seat base
toward the back of the vehicle.
03
 The entire seat will rotate toward you and stow flat in the floor. 04
 Reverse this process to return the bench seat to a seating position. Make sure to
properly install the head restraints, reattach the center seat belt, press the bench
seat down into the floor, and pull back on the seatback until it latches into place.
Sh ift_convention
to move the 2nd row seats forward or backward:
 Pull the lever up and hold it while you slide the seat forward or backward to the
desired position.
01
 Release the lever to lock the seat in position.
t o recline the 2nd row seatbacks:
 Pull the lever up and lean forward or back. 02
the 2nd row seats can be tipped forward for easy entry or exit from the 3rd row seat:
 To enter the 3rd row seats, lift up on the lever located on the lower base of the seat;
this tips the seat forward.
03
 To exit the 3rd row seats, pull back on the lever on the lower base of the seat and
push the seat forward.
t o fold the 2nd row seats flat to the floor for maximum cargo hauling:
 Remove the head restraints by lifting up each head restraint. Then, press and hold
the release button and place the head restraints in the storage bag.
 Lift up on the recline lever to fold the seatback down on the seat base. 04
 Press down on the small lever on the back of the seat to release the base of
the seat.
05
 Then fold the entire seat forward into the stowed position on the floor. 06
 Reverse this process to return the 2nd row seats to a seating position. Make sure to
properly install the head restraints and to press the seats down to the floor until they
latch into place.
ADJUSTING AND FOLDING THE 2ND ROW SEAT
01
02
FOLDING THE 3RD ROW SEAT
lo CK doo Rs
Make sure all doors and windows are closed and
press the LOCK button to secure the vehicle.
U nlo CK doo Rs
Press the UNLOCK button once to unlock the
driver’s door. Press the UNLOCK button twice
within 5 seconds to unlock all doors.
P o W eR sliding doo Rs
Press and hold the POWER SLIDING DOOR
button (if so equipped) for longer than 0.5
seconds to open or close the power sliding
door. The door will reverse direction immediately
during power open or power close if the keyfob
button is pressed. A chime will sound to indicate
the reversal.
P o W eR B aCK doo R
Press and hold the POWER BACK DOOR button (if so equipped) for longer
than 0.5 seconds to open or close the power back door. The hazard lights
will flash and a chime will sound to indicate that the power open or power
close sequence has started. If you press the button again, the door will
reverse direction immediately; a chime will sound to indicate the reversal.
R emote o Pening o F FR ont Windo Ws
Press the UNLOCK button longer than 3 seconds to open the windows. (The keyfob

is not able to close the windows after opening them.)
REMOTE KEYLESS ENTRY SYSTEM
01
02
03
04
05
06
01
0203
04
05
06
01
02
03
04
FUEL FILLER LID RELEASE
To open, press the fuel filler lid release located on the
driver’s door. To lock, securely close the fuel filler lid.

The driver’s side power sliding door is disabled when the
fuel lid is open. The sliding door can be partially opened
manually.
DOOR LOCK SWITCH
The door lock switch is located on the driver’s door armrest. Push top
of switch
01 to lock all the doors. Push bottom of the switch 02 to
unlock all the doors.
2006
QU EST

Q U I C K R E F E R E N C E G U I D E

REAR VIEW MONITOR
(if so equipped)
When the automatic transmission lever is moved to the R
(Reverse) position, the monitor display will automatically
change to show the area behind the vehicle.
The colored lines on the display screen indicate approximate
distances to objects.
 Red 1.5 feet  Yellow 3 feet  Green 7 and 10 feet
01
02

SUNROOF CONTROLS (if so equipped)
 To tilt the sunroof up, press UP. (If the roof is already
open, it will close before tilting up.) To tilt the sunroof
down, press doWn
.
 To open partially, slide the switch toward oPen. (If the
roof is tilted up, it will automatically tilt down before
opening.) To open fully, slide the switch completely to
oP en
.
 To close partially, slide the switch toward Close . To
close fully, slide the switch completely to Close .
CHILD SAFET Y DOOR LOCK
Child safety locks help prevent the sliding doors from being
opened accidentally, especially when small children are in
the vehicle. The child safety lock levers are located on the
edge of the sliding doors. When the lever is in the loCK

position, the door can be opened only from the outside, with
the overhead console switch or the keyfob.
POWER SLIDING DOORS AND POWER BACK DOOR (if so equipped)
POWER SLIDING DOORS
The power sliding doors can be
activated by the buttons on the keyfob, the overhead console, and the door pillars.
 To open, close or reverse a sliding door, the ignition switch must be off or the
automatic transmission selector lever must be in Park.
 To open, close or reverse a sliding door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To activate a sliding door with the button on the door pillar, the main on /o FF switch
must be on, the door must be unlocked, and the child safety door lock must be in the
unlock position.
 To activate the power assist feature, manually move a sliding door toward the open
or close position using the inside or outside handle. The power assist feature will
automatically complete the motion.
P OWER BACK DOOR
The power back door can be activated by the buttons on the keyfob, the overhead
console, and the rear door pillar.
 To open, close or reverse the back door, the automatic transmission lever must be
in Park.
 To open, close or reverse the back door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To close the back door with the rear door pillar button, the main on/oFF switch
must be on.
The power sliding doors and the power back door have an anti-pinch safety feature.
Please refer to your Owner’s Manual for more information regarding this feature.
AUTOMATIC DRIVER POSITIONER (if so equipped)
The automatic driver positioner system has two features:
 Memory storage function
 Entry/exit function
MEMORY STOR AGE FUNCTION
Two positions for the driver’s seat, accelerator and brake
pedals, and outside mirrors can be stored in the automatic driver positioner memory.
Follow these procedures to set driver preferences.
SET THE DESIRED POSITIONING
1. Set the automatic transmission lever to the Park position.
2. Turn the ignition on and adjust the driver’s seat, accelerator and brake pedals, and
outside mirrors to the desired positions.
3. Press the
set (memory) button and within 5 seconds press the position button (1 or 2 ) for at least 1 second until the indicator light illuminates. The position is now
stored in memory.
LINK TO KEYFOB
 Within 5 seconds of setting the memory position (indicator light is on and ignition is
on), press the
button
on the remote.
 A keyfob can be linked to each memory button.
 If memory positioning is re-set to a new location, the keyfob automatically re-links.
RECALLING A MEMORY SET TING FROM THE MEMORY PAD
 With the automatic transmission lever in the Park position, press the position button (1 or 2 ) for at least 1 second.
FROM THE KEYFOB
 If properly linked, operation of the button
will automatically return the driver’s
seat, accelerator and brake pedals, and mirrors to the memorized position.
ENTRY/ EXIT FUNCTION
The driver’s seat moves to allow the driver to get into and out of the driver’s seat more
easily. The driver’s seat slides backward when:
 The key is removed from the ignition switch.
 The driver’s door is opened with the key turned to LOCK.
 The key is turned from ACC to LOCK with the driver’s door open and the automatic
transmission lever is in the Park position.
The driver’s seat returns to the previous position when:
 The key is inserted into the ignition switch.
 The driver’s door is closed with the key turned to LOCK.
 The key is turned from ACC to ON while the automatic transmission lever is in the
Park position.
REAR SONAR SYSTEM OFF SWITCH (if so equipped)
When backing up, this system will beep to alert you to obstacles
within 6 ft. of the rear bumper. The system beeps faster as the vehicle
gets closer to the obstacle. A continuous tone sounds when an
obstacle is less than 10 inches away from the bumper. Turn the system
off by pushing the rear sonar system
oFF switch. The system will
automatically reset the next time the ignition switch is turned on.
ADJUSTABLE A CCELERATOR AND BRAKE P EDALS (if so equipped)
The accelerator and brake pedals can be adjusted for your
driving comfort.
 Adjust the pedals when the automatic transmission lever
is in Park.
 Push to
move the position of the pedals forward. 01
 Push to
move the position of the pedals backward. 02
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
 Pull up on the lever under the front of the seat and
slide backward or forward; release.
01
 Lift the lever on the side of the seat to adjust your
seatback backward or forward; release when you
have found a comfortable angle and the seat belt
fits properly.
02
 Use the dials at the side of the driver’s seat to
adjust the angle and height of the seat

cushion.
03
With power seats (if so equipped):
 Move the control forward or backward to adjust
the seat cushion forward or backward.
04
 Pull up to raise the driver’s seat cushion; press
down to lower the cushion.
04
 Push the switch forward to move the seatback
forward; press it back to move the seatback
backward.
05
Your driver’s seat has a lumbar support; adjust it by
moving the lever forward or backward.
06
to fold the 3rd row bench seat flat into the floor for maximum cargo hauling:
 Remove all 3 head restraints. Remove the head restraints by lifting up, then press
and hold the release button and continue lifting and place the head restraints in the
storage bag.
 Disconnect and secure the center seat belt and tongues into the retractor base.
Then, press the button on the seatback while pulling back on the strap to release the
back of the seat.
01
 Rotate the seatback toward the back of the vehicle. 02
 Pull up on the lever located on the back of the seat base. This will fold the seat base
toward the back of the vehicle.
03
 The entire seat will rotate toward you and stow flat in the floor. 04
 Reverse this process to return the bench seat to a seating position. Make sure to
properly install the head restraints, reattach the center seat belt, press the bench
seat down into the floor, and pull back on the seatback until it latches into place.
Sh ift_convention
to move the 2nd row seats forward or backward:
 Pull the lever up and hold it while you slide the seat forward or backward to the
desired position.
01
 Release the lever to lock the seat in position.
t o recline the 2nd row seatbacks:
 Pull the lever up and lean forward or back. 02
the 2nd row seats can be tipped forward for easy entry or exit from the 3rd row seat:
 To enter the 3rd row seats, lift up on the lever located on the lower base of the seat;
this tips the seat forward.
03
 To exit the 3rd row seats, pull back on the lever on the lower base of the seat and
push the seat forward.
t o fold the 2nd row seats flat to the floor for maximum cargo hauling:
 Remove the head restraints by lifting up each head restraint. Then, press and hold
the release button and place the head restraints in the storage bag.
 Lift up on the recline lever to fold the seatback down on the seat base. 04
 Press down on the small lever on the back of the seat to release the base of
the seat.
05
 Then fold the entire seat forward into the stowed position on the floor. 06
 Reverse this process to return the 2nd row seats to a seating position. Make sure to
properly install the head restraints and to press the seats down to the floor until they
latch into place.
ADJUSTING AND FOLDING THE 2ND ROW SEAT
01
02
FOLDING THE 3RD ROW SEAT
lo CK doo Rs
Make sure all doors and windows are closed and
press the LOCK button to secure the vehicle.
U nlo CK doo Rs
Press the UNLOCK button once to unlock the
driver’s door. Press the UNLOCK button twice
within 5 seconds to unlock all doors.
P o W eR sliding doo Rs
Press and hold the POWER SLIDING DOOR
button (if so equipped) for longer than 0.5
seconds to open or close the power sliding
door. The door will reverse direction immediately
during power open or power close if the keyfob
button is pressed. A chime will sound to indicate
the reversal.
P o W eR B aCK doo R
Press and hold the POWER BACK DOOR button (if so equipped) for longer
than 0.5 seconds to open or close the power back door. The hazard lights
will flash and a chime will sound to indicate that the power open or power
close sequence has started. If you press the button again, the door will
reverse direction immediately; a chime will sound to indicate the reversal.
R emote o Pening o F FR ont Windo Ws
Press the UNLOCK button longer than 3 seconds to open the windows. (The keyfob

is not able to close the windows after opening them.)
REMOTE KEYLESS ENTRY SYSTEM
01
02
03
04
05
06
01
0203
04
05
06
01
02
03
04
FUEL FILLER LID RELEASE
To open, press the fuel filler lid release located on the
driver’s door. To lock, securely close the fuel filler lid.

The driver’s side power sliding door is disabled when the
fuel lid is open. The sliding door can be partially opened
manually.
DOOR LOCK SWITCH
The door lock switch is located on the driver’s door armrest. Push top
of switch
01 to lock all the doors. Push bottom of the switch 02 to
unlock all the doors.
2006
QU EST

Q U I C K R E F E R E N C E G U I D E

REAR VIEW MONITOR
(if so equipped)
When the automatic transmission lever is moved to the R
(Reverse) position, the monitor display will automatically
change to show the area behind the vehicle.
The colored lines on the display screen indicate approximate
distances to objects.
 Red 1.5 feet  Yellow 3 feet  Green 7 and 10 feet
01
02

SUNROOF CONTROLS (if so equipped)
 To tilt the sunroof up, press UP. (If the roof is already
open, it will close before tilting up.) To tilt the sunroof
down, press doWn
.
 To open partially, slide the switch toward oPen. (If the
roof is tilted up, it will automatically tilt down before
opening.) To open fully, slide the switch completely to
oP en
.
 To close partially, slide the switch toward Close . To
close fully, slide the switch completely to Close .
CHILD SAFET Y DOOR LOCK
Child safety locks help prevent the sliding doors from being
opened accidentally, especially when small children are in
the vehicle. The child safety lock levers are located on the
edge of the sliding doors. When the lever is in the loCK

position, the door can be opened only from the outside, with
the overhead console switch or the keyfob.
POWER SLIDING DOORS AND POWER BACK DOOR (if so equipped)
POWER SLIDING DOORS
The power sliding doors can be
activated by the buttons on the keyfob, the overhead console, and the door pillars.
 To open, close or reverse a sliding door, the ignition switch must be off or the
automatic transmission selector lever must be in Park.
 To open, close or reverse a sliding door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To activate a sliding door with the button on the door pillar, the main on /o FF switch
must be on, the door must be unlocked, and the child safety door lock must be in the
unlock position.
 To activate the power assist feature, manually move a sliding door toward the open
or close position using the inside or outside handle. The power assist feature will
automatically complete the motion.
P OWER BACK DOOR
The power back door can be activated by the buttons on the keyfob, the overhead
console, and the rear door pillar.
 To open, close or reverse the back door, the automatic transmission lever must be
in Park.
 To open, close or reverse the back door with the keyfob, press and hold the keyfob
button for longer than 0.5 seconds.
 To close the back door with the rear door pillar button, the main on/oFF switch
must be on.
The power sliding doors and the power back door have an anti-pinch safety feature.
Please refer to your Owner’s Manual for more information regarding this feature.
AUTOMATIC DRIVER POSITIONER (if so equipped)
The automatic driver positioner system has two features:
 Memory storage function
 Entry/exit function
MEMORY STOR AGE FUNCTION
Two positions for the driver’s seat, accelerator and brake
pedals, and outside mirrors can be stored in the automatic driver positioner memory.
Follow these procedures to set driver preferences.
SET THE DESIRED POSITIONING
1. Set the automatic transmission lever to the Park position.
2. Turn the ignition on and adjust the driver’s seat, accelerator and brake pedals, and
outside mirrors to the desired positions.
3. Press the
set (memory) button and within 5 seconds press the position button (1 or 2 ) for at least 1 second until the indicator light illuminates. The position is now
stored in memory.
LINK TO KEYFOB
 Within 5 seconds of setting the memory position (indicator light is on and ignition is
on), press the
button
on the remote.
 A keyfob can be linked to each memory button.
 If memory positioning is re-set to a new location, the keyfob automatically re-links.
RECALLING A MEMORY SET TING FROM THE MEMORY PAD
 With the automatic transmission lever in the Park position, press the position button (1 or 2 ) for at least 1 second.
FROM THE KEYFOB
 If properly linked, operation of the button
will automatically return the driver’s
seat, accelerator and brake pedals, and mirrors to the memorized position.
ENTRY/ EXIT FUNCTION
The driver’s seat moves to allow the driver to get into and out of the driver’s seat more
easily. The driver’s seat slides backward when:
 The key is removed from the ignition switch.
 The driver’s door is opened with the key turned to LOCK.
 The key is turned from ACC to LOCK with the driver’s door open and the automatic
transmission lever is in the Park position.
The driver’s seat returns to the previous position when:
 The key is inserted into the ignition switch.
 The driver’s door is closed with the key turned to LOCK.
 The key is turned from ACC to ON while the automatic transmission lever is in the
Park position.
REAR SONAR SYSTEM OFF SWITCH (if so equipped)
When backing up, this system will beep to alert you to obstacles
within 6 ft. of the rear bumper. The system beeps faster as the vehicle
gets closer to the obstacle. A continuous tone sounds when an
obstacle is less than 10 inches away from the bumper. Turn the system
off by pushing the rear sonar system
oFF switch. The system will
automatically reset the next time the ignition switch is turned on.
ADJUSTABLE A CCELERATOR AND BRAKE P EDALS (if so equipped)
The accelerator and brake pedals can be adjusted for your
driving comfort.
 Adjust the pedals when the automatic transmission lever
is in Park.
 Push to
move the position of the pedals forward. 01
 Push to
move the position of the pedals backward. 02
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
 Pull up on the lever under the front of the seat and
slide backward or forward; release.
01
 Lift the lever on the side of the seat to adjust your
seatback backward or forward; release when you
have found a comfortable angle and the seat belt
fits properly.
02
 Use the dials at the side of the driver’s seat to
adjust the angle and height of the seat

cushion.
03
With power seats (if so equipped):
 Move the control forward or backward to adjust
the seat cushion forward or backward.
04
 Pull up to raise the driver’s seat cushion; press
down to lower the cushion.
04
 Push the switch forward to move the seatback
forward; press it back to move the seatback
backward.
05
Your driver’s seat has a lumbar support; adjust it by
moving the lever forward or backward.
06
to fold the 3rd row bench seat flat into the floor for maximum cargo hauling:
 Remove all 3 head restraints. Remove the head restraints by lifting up, then press
and hold the release button and continue lifting and place the head restraints in the
storage bag.
 Disconnect and secure the center seat belt and tongues into the retractor base.
Then, press the button on the seatback while pulling back on the strap to release the
back of the seat.
01
 Rotate the seatback toward the back of the vehicle. 02
 Pull up on the lever located on the back of the seat base. This will fold the seat base
toward the back of the vehicle.
03
 The entire seat will rotate toward you and stow flat in the floor. 04
 Reverse this process to return the bench seat to a seating position. Make sure to
properly install the head restraints, reattach the center seat belt, press the bench
seat down into the floor, and pull back on the seatback until it latches into place.
Sh ift_convention
to move the 2nd row seats forward or backward:
 Pull the lever up and hold it while you slide the seat forward or backward to the
desired position.
01
 Release the lever to lock the seat in position.
t o recline the 2nd row seatbacks:
 Pull the lever up and lean forward or back. 02
the 2nd row seats can be tipped forward for easy entry or exit from the 3rd row seat:
 To enter the 3rd row seats, lift up on the lever located on the lower base of the seat;
this tips the seat forward.
03
 To exit the 3rd row seats, pull back on the lever on the lower base of the seat and
push the seat forward.
t o fold the 2nd row seats flat to the floor for maximum cargo hauling:
 Remove the head restraints by lifting up each head restraint. Then, press and hold
the release button and place the head restraints in the storage bag.
 Lift up on the recline lever to fold the seatback down on the seat base. 04
 Press down on the small lever on the back of the seat to release the base of
the seat.
05
 Then fold the entire seat forward into the stowed position on the floor. 06
 Reverse this process to return the 2nd row seats to a seating position. Make sure to
properly install the head restraints and to press the seats down to the floor until they
latch into place.
ADJUSTING AND FOLDING THE 2ND ROW SEAT
01
02
FOLDING THE 3RD ROW SEAT
lo CK doo Rs
Make sure all doors and windows are closed and
press the LOCK button to secure the vehicle.
U nlo CK doo Rs
Press the UNLOCK button once to unlock the
driver’s door. Press the UNLOCK button twice
within 5 seconds to unlock all doors.
P o W eR sliding doo Rs
Press and hold the POWER SLIDING DOOR
button (if so equipped) for longer than 0.5
seconds to open or close the power sliding
door. The door will reverse direction immediately
during power open or power close if the keyfob
button is pressed. A chime will sound to indicate
the reversal.
P o W eR B aCK doo R
Press and hold the POWER BACK DOOR button (if so equipped) for longer
than 0.5 seconds to open or close the power back door. The hazard lights
will flash and a chime will sound to indicate that the power open or power
close sequence has started. If you press the button again, the door will
reverse direction immediately; a chime will sound to indicate the reversal.
R emote o Pening o F FR ont Windo Ws
Press the UNLOCK button longer than 3 seconds to open the windows. (The keyfob

is not able to close the windows after opening them.)
REMOTE KEYLESS ENTRY SYSTEM
01
02
03
04
05
06
01
0203
04
05
06
01
02
03
04
FUEL FILLER LID RELEASE
To open, press the fuel filler lid release located on the
driver’s door. To lock, securely close the fuel filler lid.

The driver’s side power sliding door is disabled when the
fuel lid is open. The sliding door can be partially opened
manually.
DOOR LOCK SWITCH
The door lock switch is located on the driver’s door armrest. Push top
of switch
01 to lock all the doors. Push bottom of the switch 02 to
unlock all the doors.
2006
QU EST

Q U I C K R E F E R E N C E G U I D E

REAR VIEW MONITOR
(if so equipped)
When the automatic transmission lever is moved to the R
(Reverse) position, the monitor display will automatically
change to show the area behind the vehicle.
The colored lines on the display screen indicate approximate
distances to objects.
 Red 1.5 feet  Yellow 3 feet  Green 7 and 10 feet
01
02