NISSAN QUEST 2012 RE52 / 4.G 08IT Navigation Manual

Black plate (92,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
5-8
Route guidance
When route guidance starts, the Small Turn
Arrow on Map is displayed in the upper left
corner of the map screen. This arrow indicates
the turning direction at the next guide point
(corner or intersection) . The distance is also
displayed. At the top of the screen, the distance
to the next guide point and the name of the next
street to turn on to are displayed. Also, there
may be cases that next street names are
announced. The Small Turn Arrow on Map can
be enabled or disabled by the user.
“Displaying small turn arrow on map”
(page 5-28)
Enlarged intersection viewWhen approaching a guide point, the system
automatically changes to the split screen and
shows an enlarged view of the intersection in the
left screen. After passing through the intersec-
tion, the system automatically returns to the full
screen mode. To switch to the full screen mode
while the enlarged intersection view is dis-
played, push <MAP>. Pushing <MAP>again
displays the enlarged intersection view.Junction guidanceWhile driving on a freeway, when the vehicle is approximately 1 mile (approximately 2 km) from a
junction, the system automatically switches to
the split screen and displays an enlarged view of
the junction (3D) in the left screen. After passing
the junction, the system automatically returns to
the full screen mode. To switch to the full screen
mode while the enlarged junction view is
displayed, push
<MAP>.
Turn listDepending on the setting, the system can
constantly display the split screen and show
the turn list in the left screen. When approaching
a guide point, the left screen automatically
switches to an enlarged view of the intersection.
To switch to the full screen mode, push
<MAP>. Pushing <MAP>again displays the
turn list.
“Turn list” (page 5-8)

Black plate (93,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
GUIDANCE SCREEN SETTINGSThe guidance screen can be displayed at all
times even when the vehicle is located away
from the guide point. The screen to be displayed
can be set.Split screen settingsThe display setting on the left-hand side screen
shown during route guidance can be changed.1. Push <ENTER> while the current location
map screen is displayed.
2. Highlight [Map View ] and push <ENTER>.
3. Highlight [View Settings] and push
<ENTER> .
4. Highlight the preferred screen and push <ENTER> . The indicator of the selected
screen illuminates.
Intersection:The map screen and the enlarged intersection
view can be displayed at the same time.
Push <MAP> to switch to the full map screen. Turn list:
The list screen for showing the guide points to
the destination and the map screen can be
displayed at the same time. An enlarged
intersection view is automatically displayed
when the vehicle approaches the guide point.
Turn list can be scrolled using the center dial,
the main directional buttons or slide switch by
touching the up/down buttons on the screen.
Push
<MAP> to switch to the full map screen.
Push <MAP> again to display the turn list.
Route guidance
5-9

Black plate (94,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
5-10
Route guidance
Fuel Economy:The current fuel consumption rate, average fuel
consumption rate, instantaneous fuel consump-
tion rate and distance to empty can be displayed
on the map screen. An enlarged intersection
view is automatically displayed when the vehicle
approaches the guide point.
Push <MAP> to switch to the full map screen.
Push <MAP> again to display the fuel economy
screen. When approaching a guide point, the
enlarged view of the intersection is automatically
displayed. To display the fuel economy informa-
tion, push <MAP>. To display the map screen,
push <MAP> again.
NOTE:
Use the values displayed on the fuel
economy screen as a guide. When the fuel
gauge indicates “E” (Empty) or the low fuel
warning light illuminates even if the dis- tance to entry reading indicates a suffi-
cient amount of fuel remains, refuel the
vehicle as soon as possible.
Full map:
The current location map is displayed. An
enlarged intersection view is automatically dis-
played when the vehicle approaches the guide
point.
When an enlarged intersection view is dis-
played, pushing
<MAP>returns to the map
screen.Show exit information on freewaysWhen the vehicle travels on a highway or a toll
road, the display automatically provides exit
information in the turn list.
1. Push <ENTER> while the current location
map screen is displayed.
2. Highlight [Map View] and push <ENTER>.3. Highlight [Map Settings] and push
<ENTER> .

Black plate (95,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
4. Highlight [Show all Freeway Exits on Route] or [Auto. Show Turn List on Freeway] and
push <ENTER>. The indicator illuminates
when the item is set.
5. Push <MAP>to return to the current
location map screen.
Showing freeway exit information:When [Show all Freeway Exits on Route] is set
to ON and the route includes a freeway or toll
road, all exits along the route which have exit
information will be shown in the turn list. The exit information is shown as icons.
Displaying turn list automatically on free-
way:
When [Auto. Show Turn List on Freeway] is set
to ON, the turn list will be automatically
displayed while the vehicle travels on a freeway
or a toll road.
Selecting a waypoint from the exit infor-
mation list:
When exit information is displayed in the turn list,
a waypoint to a facility located near the freeway
exit can be set as a waypoint.
1. Highlight the exit where the exit information
icon is displayed, and push <ENTER>. The
category list screen is displayed.
2. Highlight the landmark category and push <ENTER> . The list screen for showing
facilities located near the freeway exit is
displayed.3. Highlight the preferred facility for the way- point and push <ENTER>.
Route guidance
5-11

Black plate (96,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
5-12
Route guidance
4. The waypoint is set, and the route search is performed.
“Procedures after setting destination”
(page 5-2)
WARNING
Always stop the vehicle in a safe
location before modifying the route
conditions.
Modifying the route conditions while
driving may cause an accident.
During route guidance, the route conditions can
be modified and the route information can be
confirmed. Set route conditions according to
personal preference.BASIC OPERATION1. Push <ROUTE> .
2. Highlight the preferred setting item and push <ENTER> .
3. Push <MAP>to return to the current
location map screen.
Available setting items. [Cancel Route/Resume Route]:
Cancel the current route guidance. A
canceled route can also be reactivated. If
the suggested route is canceled, [Cancel
Route] changes to [Resume Route].
“Canceling/reactivating route”
(page 5-13)
. [Edit/Add to Route]:
Edit or add a destination or waypoints to the
route that is already set.“Editing route” (page 5-14)
. [Route Info]:
Confirm the route by the route information or
simulation. The confirmed route can also be
stored.“Confirming route” (page 5-18)
. [Guidance Settings]:
Activate or deactivate route, voice guidance
and/or traffic announcement and adjust the
volume level of voice guidance.“Guidance settings” (page 5-20)
. [Recalculate]:
Manually search for the route again after
changing the search condition.“Recalculating route” (page 5-21)
ROUTE SCREEN

Black plate (97,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
. [Detour]:
To detour from the suggested route, calcu-
late a route detouring for a specified
distance.
“Setting detour route” (page 5-22)
. [Traffic Detour]:
Manually search for an alternative detour
route taking the traffic information into
consideration.“Searching for detour route taking
traffic information into consideration”
(page 5-22)
. [Route Settings]:
Change the route calculation conditions
anywhere along the route.“Setting conditions for route calcula-
tion” (page 5-23)
CANCELING/REACTIVATING ROUTEA route that is already set can be canceled at
any time. If a route is canceled, the destination
and waypoints are also deleted.
It is also possible to reactivate a canceled route.
Canceling route1. Push <ROUTE> .
2. Highlight [Cancel Route] and push <ENTER> .3. A confirmation message is displayed.
Highlight [Yes] and push <ENTER>.
The route is canceledd along with the
destination and waypoints.
INFO:
Canceling a route does not delete destination
and waypoint information completely.“Delete destination” (page 4-20)Voice command
1. Push <TALK
>located on the steering
wheel switch.
2. After the tone sounds, speak a command. To cancel a route:
“Cancel Route” (Alternate Command Mode)
Reactivating route1. Push <ROUTE> .
2. Highlight [Resume Route] and push <ENTER> .
Route guidance
5-13

Black plate (98,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
5-14
Route guidance
3. A confirmation message is displayed. High- light [Yes] and push <ENTER>. The can-
celed route is reactivated.
INFO:
If a new route is set, the canceled route cannot
be reactivated.
EDITING ROUTE1. Push <ROUTE> .
2. Highlight [Edit/Add to Route] and push <ENTER> . 3. Highlight the preferred condition and push
<ENTER> .
4. Push <BACK> to return to the previous
screen. Push <MAP>to return to the
current location map screen.
Available setting items*1
[Add Destination]: Add a new destination.
“Setting destination or waypoint”
(page 5-14)
*2
Current destination:
Change or delete the destination.
“Editing/deleting destination or way-
point” (page 5-15)
*3
Condition for calculating a route to the
destination:
Change the conditions for calculating a
route to the destination.
“Changing route calculation condi-
tions” (page 5-17)
*4
[Add Waypoint]: Add a new waypoint.
“Setting destination or waypoint”
(page 5-14)
*5
Current waypoint:
Change or delete the waypoint.
“Editing/deleting destination or way-
point” (page 5-15)
*6
Condition for calculating a route to a
waypoint:
Change the conditions for calculating a
route to a waypoint.
“Changing route calculation condi-
tions” (page 5-17)
*7
[Calculate]:
Manually search for the route again after
changing the search conditions.
“Changing route calculation condi-
tions” (page 5-17)
Setting destination or waypointAdd a destination or waypoint to the route that is
already set. A total of 6 destinations or
waypoints can be set.

Black plate (99,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
1. Push <ROUTE> .
2. Highlight [Edit/Add to Route] and push <ENTER> .
3. Highlight [Add Destination] or [Add Way- point] and push <ENTER>.
If [Add Destination] is selected, the current
destination changes to a waypoint.4. Set a destination or waypoint. The method of searching for a destination or waypoint is the
same as the one for a destination.
“4. Setting destination”
5. The selected location is displayed at thecenter of the map. Highlight [Add to Route]
after confirming the location and push
<ENTER> .
INFO:
Even after setting a destination/waypoint,
the destination/waypoint location can be
adjusted, the route can be stored, etc.
“Editing/deleting destination or way-
point” (page 5-15)
6. Return to the Edit Route screen. Set the route conditions as necessary.
7. Highlight [Calculate] and push <ENTER>.
The system will recalculate the routes. After
the route search is completed, the display
will automatically return to the present
location screen.
INFO:
. The prior route is automatically deleted.
. Added waypoints and search conditions will
not be taken into consideration for the route
calculation until [Calculate] is highlighted
and <ENTER> is pushed.
Editing/deleting destination or waypointThe destination or waypoint that is already set
can be modified or deleted.
If a location is modified or deleted when a
suggested route is already set, the prior
suggested route will be recalculated accord-
ingly.
Route guidance
5-15

Black plate (100,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
5-16
Route guidance
1. Push <ROUTE> .
2. Highlight [Edit/Add to Route] and push <ENTER> .
3. Highlight a destination or waypoint that is already set and push <ENTER>.4. Highlight [Move Dest.] to modify the location
and push <ENTER> .
“Moving location of destination”
(page 5-4)
5. Highlight [Delete] and push <ENTER>to
delete the location.6. A confirmation message is displayed. Con- firm the contents of the message, highlight
[Yes] and push <ENTER>. The destination
or waypoint is deleted from the route. Return
to the [Edit Route] screen.
7. By highlighting [Calculate] and pushing <ENTER> , the system will recalculate the
routes. After the route search is completed,
the display will automatically return to the
present location screen.
INFO:
. If the destination is deleted, the final
waypoint of the route becomes the destina-
tion.
. When the map screen is touched, the same
map screen as when [Move Dest.] is
selected is displayed.
Changing order of destination and way-
pointsThe order of a destination and waypoints that
are already set can be changed.

Black plate (101,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
1. Push <ROUTE> .
2. Highlight [Edit/Add to Route] and push <ENTER> .
3. Highlight a destination or waypoint that is already set and push <ENTER>.4. Highlight [Change Order] and push
<ENTER> . A list of the destination and
waypoints is displayed.
5. Highlight a preferred destination or waypoint to replace the previously selected destina-
tion or waypoint and push <ENTER>.6. A message is displayed and the order of the
destination or waypoint is changed.
7. By highlighting [Calculate] and pushing<ENTER> , the system will recalculate the
routes. After the route search is complete,
the display will automatically return to the
present location screen.Changing route calculation conditionsEach section of the route between waypoints
can have different route calculation conditions.
After setting these conditions, the entire route
can be recalculated.
Route guidance
5-17