NISSAN VERSA 2006 Workshop Service Repair Manual

BL-192
FUEL FILLER LID OPENER
Revision: June 20062007 Versa
FUEL FILLER LID OPENERPFP:78820
Removal and Installation of Fuel Filler Lid OpenerEIS0093M
REMOVAL
1. Remove trunk side finisher (RH). Refer to EI-42, "Removal and Installation" .
2. Remove fuel filler lock.
3. Remove front kicking plate and rear kicking plate. Refer to EI-
32, "Removal and Installation" .
4. Remove rear cushion assembly. Refer to SE-15, "
Removal and
Installation" .
5. Remove fuel filler lid opener cable clip from the vehicle.
6. Remove the bolts and the fuel filler lid opener.
7. Remove the fuel filler lid opener cable.
INSTALLATION
Installation is in the reverse order of removal.
PIIB3831J
LIIA2629E
LIIA2670E

VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-193
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
VEHICLE SECURITY (THEFT WARNING) SYSTEMPFP:28491
Component Parts and Harness Connector LocationEIS009AX
LIIA2595E
1. Horn relay H-1 2. BCM M18, M19, M20
(view with glove box removed)3. Intelligent Key unit M52
(if equipped)
4. Combination meter M24 5. Security indicator lamp 6. Front door key cylinder switch LH
D14
7. Front door switch LH B8, RH B108 8. Rear door switch LH B6, RH B116 9. Back door lock assembly (back door
switch) D405 (with back door open)
10. Main power window and door lock/
unlock switch D7, D8
Power window and door lock/unlock
switch RH D10511. Horn (low) E18, E20 12. Horn (high) E21, E22

BL-194
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: June 20062007 Versa
System DescriptionEIS009AY
DESCRIPTION
Operation Flow

Setting the vehicle security system
Initial condition

Ignition switch is in OFF position.
Disarmed phase

When the vehicle is being driven or when any door is open, the vehicle security system is set in the dis-
armed phase on the assumption that the owner is inside or near the vehicle.
Pre-armed phase and armed phase

The vehicle security system turns into the "pre-armed" phase (security lamp illuminates) when the BCM
receives LOCK signal from front door key cylinder switch, keyfob or Intelligent Key after all doors are
closed.

All doors are closed after front doors are locked by key or door lock and unlock switch.
The security indicator lamp illuminates for 30 seconds. then, the system automatically shifts into the "armed"
phase.
Canceling the set vehicle security system
The armed phase is canceled when the driver unlocks the doors with the key, keyfob or Intelligent Key.
Activating the alarm operation of the vehicle security system
Make sure the system is in the armed phase.
When one of the following operations is performed, the system sounds the horns and flashes the headlamps
for about 50 seconds.
1. Any door is opened before unlocking door with key, keyfob or Intelligent Key.
2. Door is unlocked without using key, keyfob or Intelligent Key.
POWER SUPPLY AND GROUND
Power is supplied at all times

through 10A fuse [No.13, located in the fuse block (J/B)]

to combination meter terminal 27 (security indicator lamp)

through 40A fusible link (letter g , located in the fuse and fusible link box)

to BCM terminal 70

through 10A fuse [No. 8, located in the fuse block (J/B)]

to BCM terminal 57
PIIA1367E

VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-195
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa

through 10A fuse (No. 28, located in the fuse and fusible link box)

to horn relay terminal 2

through 15A fuse (No. 52, located in the IPDM E/R)

to IPDM E/R internal CPU.

through 20A fuse (No. 53, located in the IPDM E/R)

to IPDM E/R internal CPU.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 20, located in the fuse block (J/B)]

to BCM terminal 11.
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 6, located in the fuse block (J/B)]

to BCM terminal 38.
Ground is supplied

to BCM terminal 67

through body grounds M57 and M61.
INITIAL CONDITION TO ACTIVATE THE SYSTEM
The operation of the vehicle security system is controlled by the doors.
To activate the vehicle security system, BCM must receive signals indicating the ignition switch is OFF, doors
are closed and locked.
When a door is open, BCM terminal 12, 13, 43, 47 or 48 receives a ground signal from each door switch. In
addition to BCM, when back door is open, the Intelligent Key unit terminal 23 receives a ground signal from
back door through BCM terminal 30.
When front door LH is unlocked, BCM terminal 46 receives a signal from terminal 6 of main power window and
door lock/unlock switch.
When front door RH is unlocked, BCM terminal 46 receives a signal from terminal 2 of power window and door
lock/unlock switch RH.
VEHICLE SECURITY SYSTEM ALARM OPERATION
The vehicle security system is triggered by

opening a door

unlocking door without using the key, keyfob or Intelligent Key.
The vehicle security system will be triggered once the system is in armed phase,

when BCM receives a ground signal at terminals 12, 13, 47, 48 (front or rear door switch), or terminal 43
(back door switch).
When the vehicle security system is triggered, ground is supplied intermittently

from IPDM E/R terminal 45

to horn relay terminal 1.
The headlamps flash and the horn sounds intermittently.
The alarm automatically turns off after 50 seconds, but will reactivate if the vehicle is tampered with again.
VEHICLE SECURITY SYSTEM DEACTIVATION
To deactivate the vehicle security system, a door must be unlocked with the key, keyfob or Intelligent Key.
When the key is used to unlock the driver door, BCM terminal 7 receives signal

from terminal 3 of the front door key cylinder switch LH.
When the BCM receives this signal or unlock signal from keyfob or Intelligent Key or front door key cylinder
switch LH, the vehicle security system is deactivated. (Disarmed phase)
PANIC ALARM OPERATION
Intelligent Key and remote keyless entry system may or may not operate vehicle security system (horn and
headlamps) as required.
When the remote keyless entry system is triggered, ground is supplied intermittently

from IPDM E/R terminal 45

to horn relay terminal 1.
The headlamp flashes and the horn sounds intermittently.

BL-196
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: June 20062007 Versa
The alarm automatically turns off after 25 seconds or when BCM receives any signal from keyfob or Intelligent
Key.
CAN Communication System DescriptionEIS009AZ
Refer to LAN-4, "SYSTEM DESCRIPTION" .

VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-197
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
SchematicEIS009B0
WIWA1971E

BL-198
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: June 20062007 Versa
Wiring Diagram — VEHSEC —EIS009B1
WIWA1972E

VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-199
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
WIWA1973E

BL-200
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: June 20062007 Versa
WIWA1974E

VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-201
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
LIWA0555E