NISSAN X-TRAIL 2003 Service Repair Manual

DOOR FINISHER
EI-33
C
D
E
F
G
H
J
K
L
MA
B
EI

2. Insert a screwdriver, wrapped with a cloth, into the cutout on the
front edge of power window switch finisher. Unfasten the metal
clip on the front side.
3. Insert the screwdriver into the gap and remove metal clips, mov-
ing from front to rear.
4. Disconnect and remove power window switch connector.
5. Remove door finisher mounting screw.
6. Insert a screwdriver, wrapped with a cloth, into the cutout on the
lower part of door finisher. Unfasten the clips.
7. Pull the door finisher upwards to remove.
Installation
Installation is in the reverse order of removal.
NOTE:

Insert a clip driver or clip clamp remover into the part shown by
the arrow (between the body side panel and the clips). Remove
finisher.

To install the finisher, confirm clips are surely aligned with the
holes on the body side panel, then press in.
SIIA0208J
SIIA0211J
SIIA0213J
SIIA0810E

EI-34
BACK DOOR TRIM

BACK DOOR TRIMPFP:90900
Removal and InstallationEIS000NA
REMOVAL
1. Remove clips of back door trim.
2. Remove back door trim.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:

Insert a clip driver or clip clamp remover into the part shown by
the arrow (between the clips and the body side panel). Remove
clips.

When installing, confirm clips are surely aligned with the holes
on the body side panel, then press in.
SIIA0221E
PIIA0527E

BODY SIDE TRIM
EI-35
C
D
E
F
G
H
J
K
L
MA
B
EI

BODY SIDE TRIMPFP:76913
Removal and InstallationEIS000NB
PIIB0591E
1. Front pillar garnish 2. Dashboard side finisher 3. Front body side welt
4. Front kick panel 5. Center pillar upper garnish 6. Center pillar lower garnish
7. Rear body side welt 8. Rear kick panel 9. Rear pillar finisher
10. Luggage side lower finisher 11. Front luggage floorboard 12. Luggage floor rear spacer (right)
13. Luggage floor rear spacer (center) 14. Luggage floor rear spacer (left) 15. Luggage floorboard (right)
16. Rear luggage floorboard 17. Luggage floorboard (left) 18. Luggage rear plate
19. Back door weather strip 20. Hook 21. Net
22. Tonneau cover

EI-36
BODY SIDE TRIM

CENTER PILLAR LOWER GARNISH
Removal
Remove front and rear kick panels.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR UPPER GARNISH
Removal
1. Remove seat belt shoulder anchor bolt. Refer to SB-3, "Removal and Installation of Front Seat Belt" .
2. Remove front and rear kick panels.
3. Remove center pillar lower garnish.
Installation
Installation is in the reverse order of removal.
LUGGAGE SIDE LOWER FINISHER
Removal
1. Remove luggage floorboards and luggage floor spacers.
2. Remove luggage rear plate.
3. Remove rear kick panel.
NOTE:
When removing or installing, pay attention to pawl engagement with the rear pillar finisher.
Installation
Installation is in the reverse order of removal.
REAR PILLAR FINISHER
Removal
1. Removal luggage side lower finisher.
2. Removal rear seat belt shoulder anchor. Refer to SB-4, "
Removal and Installation of Rear Seat Belt" .
Installation
Installation is in the reverse order of removal.
DASHBOARD SIDE FINISHER
Removal
Removal dash side finisher.
Installation
Installation is in the reverse order of removal.
BODY SIDE WELT
Removal
1. Remove kick panels.
2. Remove center pillar lower garnish.
3. Remove center pillar upper garnish.
SIIA0261E

BODY SIDE TRIM
EI-37
C
D
E
F
G
H
J
K
L
MA
B
EI

NOTE:

Insert a screwdriver, wrapped with a cloth, into the part shown
by an arrow (between the body side panel and clips). Remove
clips.

When installing, confirm clips are aligned with the body side
panel holes, and then press in.
SIIA0810E

EI-38
FLOOR TRIM

FLOOR TRIMPFP:74902
Removal and InstallationEIS000NC
REMOVAL
1. Remove front seat and rear seat cushions. Refer to SE-26, "Removal and Installation" and SE-33,
"Removal and Installation" .
2. Remove clips and remove rear floor carpet.
3. Remove center console.
4. Remove lower instrument cover.
5. Remove lower instrument center panel.
6. Remove floor anchor bolt of front seat belt. Refer to SB-3, "
Removal and Installation of Front Seat Belt" .
7. Remove front and rear kick panels.
8. Remove center pillar lower garnish.
9. Remove front and rear body-side welts.
10. Remove the dashboard side finisher.
11. Remove footrest.
12. Remove carpet hooks and clips.
13. Remove carpet from the carpet anchor clips.
14. Remove floor carpet.
NOTE:

For steps 3-5, refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .

For steps 7-10, refer to EI-35, "Removal and Installation" .
INSTALLATION
Installation is in the reverse order of removal.
SIIA0222E
1. Floor carpet 2. Foot rest 3. Carpet hook
4. Model number plate cover 5. Rear floor carpet

HEADLINING
EI-39
C
D
E
F
G
H
J
K
L
MA
B
EI

HEADLININGPFP:73910
Removal and InstallationEIS000ND
REMOVAL
1. Remove front pillar and center pillar garnishes. Refer to EI-35, "Removal and Installation" .
2. Remove body side welt. Refer to EI-35, "
Removal and Installation" .
3. Remove rear pillar finisher. Refer to EI-35, "
Removal and Installation" .
SIIA0223E
1. Headlining (standard) 2. Sun-visor (left) 3. Sun-visor (right)
4. Sun-visor holder 5. Inside mirror 6. Inside mirror cover
7. Map lamp 8. Interior lamp 9. Assistance grip (fixed type)
10. Luggage compartment lamp 11. Headlining (sunroof) 12. Sunroof switch and map lamp
13.Assistance grip (retractable
type)14. Sunroof welt

EI-40
HEADLINING

4. Remove assistance grip.
NOTE:
When removing the assistant's grip cover from a car with a sun-
roof, use a clip clamp tool to disengage the upper and lower
tabs, then slide inwards and remove screws (1 each on left/
right).
5. Remove map lamp, interior lamp, and luggage compartment lamp. Refer to LT- 8 7 , "
INTERIOR ROOM
LAMP" , LT- 9 1 , "MAP LAMP (WITHOUT SUNROOF)" , LT- 9 1 , "MAP LAMP (WITH SUNROOF)" and LT-
87, "LUGGAGE ROOM LAMP" .
6. Remove inside mirror cover.
7. Remove mounting screw on inside mirror.
8. Remove sun visors (driver side and passenger side).
9. Remove headlining rear clips.
10. Remove sun visor holder.
NOTE:
Insert a screwdriver into the cutout and rotate 90° to remove.
11. Remove headlining through the back door opening.
NOTE:

Removal and installation must be performed by 2 persons.

Do not strongly bend the headlining.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
When installing, insert the protrusions on the headlining into the
holes in the upper part of center pillar.
SIIA0052E
SIIA0224J
PIIA0561E

IP-1
INSTRUMENT PANEL
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION
A
B
IP

INSTRUMENT PANEL
PRECAUTIONS .......................................................... 2
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 2
Precautions .............................................................. 2
PREPARATION ........................................................... 3
Commercial Service Tools ........................................ 3
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 4
Work Flow ................................................................ 4
CUSTOMER INTERVIEW ..................................... 4
DUPLICATE THE NOISE AND TEST DRIVE ....... 5
CHECK RELATED SERVICE BULLETINS ........... 5
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 5
REPAIR THE CAUSE ........................................... 5
CONFIRM THE REPAIR ....................................... 6
Generic Squeak and Rattle Troubleshooting ........... 6INSTRUMENT PANEL .......................................... 6
CENTER CONSOLE ............................................. 6
DOORS ................................................................. 6
TRUNK .................................................................. 7
SUNROOF/HEADLINING ..................................... 7
SEATS ................................................................... 7
UNDERHOOD ....................................................... 7
Diagnostic Worksheet ............................................... 8
INSTRUMENT PANEL ASSEMBLY ......................... 10
Component Parts Location ..................................... 10
Removal and Installation ........................................ 11
WORK ITEM TABLE ............................................ 11
REMOVAL ........................................................... 12
INSTALLATION ................................................... 18
Disassembly and Assembly .................................... 19
CENTER CONSOLE ........................................... 19
INSTRUMENT CENTER LOWER PANEL .......... 21

IP-2
PRECAUTIONS

PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EIS0046I
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions EIS001NZ

Disconnect both battery cables in advance.

Disconnect air bag system line in advance.

Never tamper with or force air bag lid open, as this may adversely affect air bag performance.

Be careful not to scratch pad and other parts.

When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which
may get in the way with cloth.

When removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl or tape.

Keep removed parts protected with cloth.

If a clip is deformed or damaged, replace it.

If an unreusable part is removed, replace it with a new one.

Tighten bolts and nuts firmly to the specified torque.

After re-assembly has been completed, make sure each part functions correctly.

Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain
with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.

Do not use any organic solvent, such as thinner or benzine.