wheel NISSAN X-TRAIL 2013 Owner´s Manual


> (GLW    0RGHO 7$@
6 In case ofemergency
Hazard indicator flasherswitch ....
........................................................... .6-2
Flat tire....
........................................................... ............................................6-2
Tire Pressure Monitoring System(TPMS) (ifequipped) ....
........ 6-2
Stopping vehicle....
............................................ ...................................6-2
Preparing toolsandspare tire(ifequipped) ....
............................. 6-3
Blocking wheels....
................................................. ...............................6-5
Removing wheelcover(ifequipped) ....
........................................... 6-6
Removing tire....
...................................................... ...............................6-6Installing
sparetire....
........................................................... ..............6-7
Stowing damaged tireand tools ....
................................................ 6-7
Jump starting ....
............................................ ................................................ 6-8
Push starting ....
............................................ ............................................. 6-10
If your vehicle overheats ....
............................................ ........................6-10
T owing yourvehicle ....
................................................. ............................6-11
T owing precautions ....
...................................................... ...............6-11
T owing recommended byNISSAN ....
......................................... 6-11
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
6-2
In case ofemergency
T32A1308 27-1CA14978 -018C-4DAF-9882-1F9 A0A0A23F 2
SIC2475
The hazard indicator flasherswitchoperates regard-
less ofthe ignition switchposition exceptwhenthe
battery isdischarged.
The hazard indicator flasherisused towarn other
drivers whenyouhave tostop orpark under
emergency conditions.
When thehazard indicator flasherswitchispushed, all
turn signal lightswillflash. To turn offthe hazard
indicator flasher,pushthehazard indicator flasher
switch again.
When animpact thatcould activate thesupplemental
air bags isdetected, thehazard warning flasherlights
blink automatically .If the hazard warning flasherswitch
is pushed, thehazard warning flasherswillturn off.
WARNING:
Do not turn thehazard warning flasherswitchto
off until youcanmake surethatitis safe todo
so. Also, thehazard flasher warning maynot
blink automatically dependingonthe force of
impact.
T32A130827-5 BBC013D-2895-406E -B78D-DB3360F5A392
If you have aflat tire, follow theinstructions asfollows.
TIRE PRESSURE MONITORING SYSTEM
(TPMS) (ifequipped)
GUID-5E03 39A0-2DD1- 4BAB-A41C-59B791FC2 152
WARNING:
. Ifthe low tirepressure warninglightillumi-
nates whiledriving, avoidsudden steering
maneuvers orabrupt braking, reducevehicle
speed, pulloffthe road toasafe location
and stop thevehicle assoon aspossible.
Driving withunder-inflated tiresmayperma-
nently damage thetires andincrease the
likelihood oftire failure. Serious vehicle
damage couldoccurandmay lead toan
accident andcould result inserious personal
injury. Check thetire pressure forallfour
tires. Adjust thetire pressure tothe recom-
mended COLDtirepressure shownonthe
tire placard toturn thelow tirepressure
warning lightoff.Ifthe light stillilluminates
while driving afteradjusting thetire pres-
sure, atire may beflat. Ifyou have aflat tire,
replace itwith aspare tire(ifequipped) as
soon aspossible.
. When aspare tireismounted orawheel is
replaced, theTPMS willnotfunction andthe
low tirepressure warninglightwillflash for
approximately 1minute. Thelight willre-
main onafter the1minute. Contact a
NISSAN dealerassoon aspossible fortire
replacement and/orsystem resetting.
. Replacing tireswiththose notoriginally
specified byNISSAN couldaffect theproper
operation ofthe TPMS.
The Tire Pressure Monitoring System(TPMS) monitors
tire pressure ofall tires except thespare. Whenthelow tire
pressure warninglightislit, one ormore ofyour
tires issignificantly under-inflated. Ifthe vehicle is
being driven withlowtirepressure, theTPMS will
activate andwarn youofitby the low tirepressure
warning light(inthe meter panel).This system will
activate onlywhen thevehicle isdriven atspeeds
above 25km/h (16MPH) .
For more details, seeªLow tirepressure warninglightº
(P .2-14) andªTire Pressure Monitoring System
(TPMS)º (P.5-4) .
ST OPPING VEHICLE
T32A1308 27-40DAB50 9-FB3E-4FB9-8C5E-CC9C163BB1F4
WARNING:
. Besure toapply theparking brakefirmly.
. Besure tomove theshift lever tothe ªPº
(Park) position (Continuously Variable
T ransmission model)orthe shift lever to
the ªRº(Reverse) position(ManualTransmis-
sion model) .
. Never change tireswhen thevehicle ison a
slope, iceorslippery area.Thisishazardous.
. Never change tireswhen theoncoming
traffic isclose toyour vehicle. Callfor
professional roadassistance.
1. Safely movethevehicle offthe road away from
traffic.
2. Turn onthe hazard indicator flasherlights.
3. Park onalevel surface.
4. Apply theparking brake.
5. Continuously Variable Transmission (CVT)model:
Move theshift lever tothe ªPº (Park) position.
Manual Transmission (MT)model: Movetheshift
lever tothe ªRº (Reverse) position.
HAZARD INDICATOR FLASHER
SWIT CH FLA
TTIRE
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
SCE0367A
Remove theclamp holding thespare tire.
Spare tire(Three rowmodel)
GUID-2B977 AFD-78CE-45B8-AD6A-5 1FC23CEF 1AF
JVE0166X
The spare tireislocated undertheluggage floor-
boards.
Fold thethird rowseats flatand then remove the
luggage floorboard
*
1
. For folding thethird row
seats, seeªThird rowseatsº (P.1-6) .
Pull thestrap
*
2
to raise theseat.
Remove thecover
*
3
.
SCE0367A
Remove theclamp holding thespare tire.
BL OCKING WHEELS
T32A130 827-6A7B1 011-550C-43 58-9F60-727 F236E60FB
MCE0001D
WARNING:
Be sure toblock theappropriate wheelto
prevent thevehicle frommoving, whichmay
cause personal injury.
Place suitable blocks
*
1
at both thefront andback of
the wheel diagonally oppositetheflattire
*
A
to
prevent thevehicle frommoving whenitis jacked up.
In case ofemergency
6-5
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
6-6
In case ofemergency
REMOVING WHEELCOVER (ifequipped)
GUID-367 4401C-151D -43A1-9DF6-7296428 8CB88
SCE0630
WARNING:
Never useyour hands toremove thewheel
cover. Thismaycause personal injury.
T o remove thewheel cover, usethejack rod
*
1
as
illustrated.
Apply cloth
*
2
between thewheel andjack rodto
prevent damaging thewheel andwheel cover.
REMOVING TIRE
T32A1308 27-A4847D3 3-094A-426F- AC3E-6A473AA5D 740
JVE0165X
Jack -uppoints
Jacking upvehicle
T32A1308 27-DBAE999 F-CE6C-44E9 -9569-9ED9 514CF77B
SCE0574
WARNING:
. Besure toread andfollow theinstructions in
this section.
. DO NOTGET UNDER AVEHICLE THATIS
SUPPORTED BY A JACK .
. Never useajack which isnot provided with
your vehicle.
. The jack, which isprovided withyour vehicle,
is designed onlytolift your vehicle duringa
tire change. Donot use thejack provided
with your vehicle onother vehicles.
. Never jackupthe vehicle atalocation other
than thejack -uppoint thatisspecified.
. Never liftthe vehicle morethannecessary.
. Never useblocks onorunder thejack.
. Never startorrun theengine whilethe
vehicle ison the jack. Thevehicle maymove
suddenly, andthismay cause anaccident.
. Never allowpassengers toremain inthe
vehicle whilethetire isoff the ground. .
Besure toread thecaution labelattached to
the jack body before using.
1. Place thejack directly underthejack-up point as
illustrated sothat thetop ofthe jack contacts the
vehicle atthe jack-up point.
The jack should beplaced onfirm level
ground.
2. Align thejack head between thetwo notches
located atthe jack-up point ofeither thefront or
the rear section.
3. Fitthe groove ofthe jack head between the
notches asshown.
4. Loosen eachwheel nut,counterclockwise, oneor
two turns withthewheel nutwrench.
Do not remove thewheel nutsuntil thetire is
off the ground.
5. Carefully raisethevehicle untiltheclearance
between thetireand ground isachieved.
6. To lift the vehicle, securely holdthejack lever and
rod with both hands andturn thejack lever.
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
Removing tire
T32A1308 27-9C9287 25-DE13-45 24-B106-43C BCA933524
1. Remove thewheel nuts.
2. Remove thedamaged tire.
CAUTION:
The tireisheavy. Besure thatyour feetareclear
from thetire and usegloves asnecessary to
avoid injury.
INST ALLING SPARE TIRE
T32A1308 27-435AF232-C329 -432F-8AAD-7 473B8100EC 2
SCE0039
WARNING:
. Never usewheel nutswhich arenot provided
with your vehicle. Incorrect wheelnutsor
improperly tightenedwheelnutsmaycause
the wheel tobecome looseorcome off.This
could cause anaccident.
. Never useoilorgrease onthe wheel studs
or nuts. Thismaycause thewheel nutsto
become loose.
. The T-type spare tireisdesigned foremer-
gency useonly. 1.
Clean anymud ordirt from thesurface between
the wheel andhub.
2. Carefully putthespare tireonand tighten the
wheel nutswithyour fingers. Checkthatallthe
wheel nutscontact thewheel surface horizontally .
3. Tighten thewheel nutsalternately andevenly in
the sequence illustrated(
*
1
-
*
5
) , more than2
times withthewheel nutwrench, untilthey are
tight.
4. Lower thevehicle slowlyuntilthetire touches the
ground.
5. Tighten thewheel nutssecurely ,with thewheel
nut wrench, inthe sequence illustrated.
6. Lower thevehicle completely .
Tighten thewheel nutstothe specified torque
with atorque wrench assoon aspossible.
Wheel nuttightening torque:
108 N´m (11kg-m, 80ft-lb)
The wheel nutsmust bekept tightened to
specification atall times. Itis recommended
that thewheel nutsbetightened tospecification
at each lubrication interval.
WARNING:
Retighten thewheel nutswhen thevehicle has
been driven for1,000 km(600 miles) (alsoin
cases ofaflat tire, etc.).
For models equipped withTirePressure
Monitoring System(TPMS)
GUID-16DE 3A91-C3BF -444C-BA0B-738A18EB BE53
. After adjusting thetire pressure, theTPMS must
be reset. SeeªTire Pressure Monitoring System
(TPMS)º (P.6-2) ,ªTire Pressure Monitoring Sys-
tem (TPMS)º (P.5-4) andªTire Pressure Monitor-
ing System (TPMS)º (P.8-36) fordetails aboutthe
resetting procedure.
. After adjusting tirepressure tothe COLD tire
pressure, thedisplay ofthe tire pressures (if
equipped inthe vehicle information display)may
show higher pressure thantheCOLD tire
pressure afterthevehicle hasbeen driven more
than 1.6km(1mile) .This isbecause thetire
pressurizes asthe tire temperature rises.This
does notindicate asystem malfunction.
ST OWING DAMAGED TIREANDTOOLS
T32A1308 27-5EF8CC3 C-3891-4896-8173-496E49108424
WARNING:
. Besure thatthetire, jack andtools usedare
properly storedafteruse.Such items can
become dangerous projectilesinan accident
or sudden stop.
. The T-type spare tireisdesigned foremer-
gency useonly.
1. Securely storethedamaged tire,jack andtools
used inthe storage areainthe reverse orderof
removal. (SeeªPreparing toolsandspare tireº
(P .6-3) .)
2. Replace theluggage floorboards.
3. Close theback door.
In case ofemergency
6-7
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
1. Ifthe booster batteryisin another vehicle
*
B
,
position thetwo vehicles
*
A
and
*
B
to bring the
batteries intoclose proximity toeach other.
CAUTION:
If the battery ofvehicle
*
A
equipped withthe
Intelligent Keysystem isdischarged, theignition
switch cannot bemoved fromtheªLOCKº
position and,ifthe steering lockisengaged,
the steering wheelcannot bemoved. Connect
the jumper cablestothe booster vehicle
*
B
before turning orpushing theignition switchand
disengaging thesteering lock.
2. Apply theparking brake.
3. Continuously Variable Transmission (CVT)model:
Move theshift lever tothe ªPº (Park) position.
Manual Transmission (MT)model: Movetheshift
lever tothe ªNº (Neutral) position.
4. Switch offallunnecessary electricalsystems
(headlights, heater,airconditioner, etc.).
5. Place theignition switchinthe ªLOCKº position.
6. Remove thevent caps, ifequipped, onthe battery .
7. Cover thebattery withafirmly wrung outmoist
cloth toreduce thehazard ofan explosion.
8. Connect thejumper cablesinthe sequence as
illustrated (
*
1
,
*
2
,
*
3
,
*
4
) .
CAUTION:
. Always connect positive +topositive +and
negative 7tobody ground, NOTto the
battery's negative7.
. Besure thatthejumper cablesdonot touch
moving partsinthe engine compartment. .
Besure thatthejumper cable's clamps do
not contact anyother metal.
9. Start theengine ofthe booster vehicle
*
B
and let
it run forafew minutes.
10. Depress theaccelerator pedalofthe booster
vehicle
*
B
at about 2,000 rpm.
11. Start theengine ofthe jumped vehicle
*
A
in the
normal manner.
CAUTION:
Never keepthestarter motorengaged formore
than 10seconds. Ifthe engine doesnotstart
right away, placetheignition switchªOFFºand
wait atleast 10seconds beforetryingagain.
12. After theengine isstarted, carefully disconnect
the jumper cablesinthe opposite sequence from
that illustrated (
*
4
,
*
3
,
*
2
,
*
1
) .
13. Remove anddispose ofthe cloth asitmay be
contaminated withcorrosive acid.
14. Replace thevent caps, ifremoved.
NO TE:
. For model withStop/Start SystemorIdling
Stop System, usethespecial batterythatis
enhanced inregard tothe charge-discharge
capacity andlifeperformance. Avoidusinga
non-special batteryforthe Stop/Start Sys-
tem orIdling StopSystem, asthis may cause
early deterioration ofthe battery oramal-
function ofthe Stop/Start SystemorIdling
Stop System. Forthebattery, itis recom-
mended touse Genuine NISSANparts.For
more information, contactaNISSAN dealer. .
For model withStop/Start SystemorIdling
Stop System, itmay take some timeuntil
Stop/Start SystemorIdling StopSystem
activates whenthebattery isreplaced orthe
battery terminal isdisconnected forex-
tended periods andthen reconnected.
In case ofemergency
6-9
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
T32A1308 27-5ADBFD CE-C556-495F-8294-4EF D4BFC5099
When towing yourvehicle, localregulations fortowing
must befollowed. Incorrecttowingequipment could
damage yourvehicle. To assure propertowing andto
prevent accidental damagetoyour vehicle, NISSAN
recommends thatyouhave professional roadassis-
tance personnel towyour vehicle. Itis advisable to
have theprofessional roadassistant carefullyreadthe
following precautions.
T OWING PRECAUTIONS
T32A1308 27-7E42C15 2-10BF-4374-A885-0A3 D89794DC3
. Besure thatthetransmission, steeringsystem,
and drivetrain areinworking condition before
towing. Ifany units aredamaged, thevehicle must
be towed usingadolly orflatbed towtruck. (Two-
Wheel Drive(2WD) model)
. NISSAN recommends thatyour vehicle betowed
with thedriving (front)wheels offthe ground.
(T wo-Wheel Drive(2WD) model)
. Always attachsafetychains beforetowing.
. Never towFour-Wheel Drive(4WD) modelwith
any ofthe wheels onthe ground asthis may cause
serious andexpensive damagetothe drivetrain.
T OWING RECOMMENDED BY NISSAN
T32A1308 27-4F07BA 95-CC62-4AA4-95CD-C7 5F7896FA0C
T owing Two-Wheel Drive(2WD) model
T32A1308 27-20FA02AA-F81 7-48A2-B25 D-1D1DCBE 00315
JVE0167X
2WD model
JVE0168X
2WD model
Front wheels onthe ground:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
NISSAN recommends thattowing dolliesbeused
under thefront wheels whentowing yourvehicle orthe
vehicle beplaced onaflatbed towtruck asillustrated.
CAUTION:
Never towContinuously Variable Transmission
(CVT) model withthefront wheels onthe
ground. Doingsowill cause serious andexpen- sive
damage tothe drivetrain.
Manual Transmission (MT)model:
If you have totow aMT vehicle withfront wheel onthe
ground, perform thefollowing procedures.
1. Place theignition switchinthe ªOFFº position.
2. Secure thesteering wheelinastraight-ahead
position withrope orasimilar device.
3. Move theshift lever tothe ªNº (Neutral) position.
4. Release theparking brake.
5. Attach thesafety chains whenever towing.
Rear wheels onthe ground:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
1. Place theignition switchinthe ªOFFº position.
2. Move theshift lever tothe ªNº (Neutral) position.
3. Release theparking brake.
4. Attach safetychains whenever towing.
All four wheels onthe ground:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
NISSAN recommends thatthevehicle beplaced ona
flatbed towtruck asillustrated.
CAUTION:
Never towCVT model withallfour wheels onthe
ground. Doingsowill cause serious andexpen-
sive damage tothe drivetrain.
Manual Transmission (MT)model:
If you have totow aMT vehicle withallfour wheels on
the ground, perform thefollowing procedures.
CAUTION:
. Never towamanual transmission model
backward withallfour wheels onthe
ground.
In case ofemergen cy
6-11
T
OWING YOUR VEHICLE
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
6-12
In case ofemergency
1. Place theignition switchinthe ªOFFº position.
2. Move theshift lever tothe ªNº (Neutral) position.
3. Release theparking brake.
T owing Four-Wheel Drive(4WD) model
T32A130827- 693E447E-03E7-4D37-A2 93-4348DD 8C9B5B
JVE0169X
4WD model
JVE0170X
4WD model
NISSAN recommends thattowing dolliesbeused
under thefront orrear wheels whentowing your
vehicle orthe vehicle beplaced onaflatbed towtruck
as illustrated.
CAUTION:
Never tow4WD withanyofthe wheels onthe
ground. Doingsowill cause serious andexpen-
sive damage tothe drivetrain.
Freeing trapped vehicle
GUID-12A4 552C-8AF3 -492C-8958-3 AD857FAAFD4
WARNING:
. Never allowanyone tostand nearthetowing
line during thepulling operation.
. Never spinthetires athigh speed. Thiscould
cause themtoexplode andresult inserious
injury. Partsofthe vehicle couldalsoover-
heat andbedamaged.
. Donot pull thevehicle usingtherear hook
(except forEurope andIndonesia) .The rear
hook isnot designed topull thevehicle out
in the event thatthevehicle becomes
trapped.
In the event thatyour vehicle's tiresbecome trappedin
sand, snow,or mud, andthevehicle isunable tofree
itself without beingpulled, usetherecovery hooks.
. Use therecovery hooksonly.Do not attach the
pulling devicetoany other partofthe vehicle body.
Otherwise, thevehicle bodymaybedamaged.
. Use therecovery hookstofree avehicle only.
. The recovery hooksareunder tremendous stress
when usedtofree atrapped vehicle.Alwayspull
the pulling devicestraight outfrom thevehicle.
Never pullonthe recovery hooksatan angle. Front
:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94A EAE0
JVE0158X
Front
SCE0833
Front
*
1
Remove thehook cover fromthebumper witha
suitable tool.
*
2
Securely installtherecovery hookasillustrated.
(The hook isstored inthe storage area.)
Make surethattherecovery hookisproperly secured
in its storage areaafter use.
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
7 Appearance andcare
Cleaning exterior....
........................................................... ...........................7-2
W ashing ....
........................................................... ...................................7-2
Removing spots....
...................................................... ...........................7-2
W axing ....
................................................. ................................................ 7-2
Glass ....
....................................... ............................................................. 7-2
Underbody ....
........................................................... ...............................7-3
Wheels ....
................................................. ................................................ 7-3
Aluminum alloywheels ....
...................................................... ..............7-3
Chrome parts....
...................................................... ...............................7-3Cleaning
interior....
........................................................... ...........................7-3
Air fresheners ....
................................................................ ..................7-4
Floor mats ....
...................................................... ...................................7-4
Glass ....
...................................................... ............................................7-4
Seat belts ....
...................................................... ...................................7-4
Corrosion protection ....
................................................................ ..............7-5
Most common factorscontributing tovehicle corrosion ....
...... 7-5
Environmental factorsinfluence rateofcorrosion ....
.................. 7-5
T o protect yourvehicle fromcorrosion ....
..................................... 7-5
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
7-2
Appear anceandcare
T32A1308 27-B546E8 D4-F62E-4E44-86B7-FD A25D20C022
In order tomaintain theappearance ofyour vehicle, itis
important totake proper careofit.
Whenever possible,parkyourvehicle insideagarage
or inacovered areatominimize thechances of
damaging thepaint surface ofyour vehicle.
When itis necessary topark outside, parkinashady
area orprotect thevehicle withabody cover. Be
careful nottoscratch thepaint surface when
putting onorremoving thebody cover.
W ASHING
T32A130827-7 5EA71EE-82C3-45D9-8 9B6-534587A2F13A
In the following instances, washyourvehicle assoon
as possible toprotect thepaint surface:
. After arainfall, whichmaycause thepaint surface
damage fromacidrain.
. After driving oncoastal roads,whichmaycause
rusting fromthesea breeze.
. When contaminants suchassoot, birddroppings,
tree sap, metal particles orbugs getonthe paint
surface.
. When dustormud builds uponthe paint surface.
1. Wash thevehicle surface withawet sponge and
plenty ofwater.
2. Clean thevehicle surface gentlyandthoroughly
using amild soap, aspecial vehiclesoapora
general purpose dishwashing liquidmixed with
clean, lukewarm (neverhot)water.
CAUTION:
. Donot wash thevehicle withstrong house-
hold soap, strong chemical detergents, ga-
soline orsolvents.
. Donot wash thevehicle indirect sunlight or
while thevehicle bodyishot, asthe paint
surface maybecome water-spotted. .
Avoid usingtight-napped orrough cloths,
such aswashing mitts.Caremust betaken
when removing caked-ondirtorother for-
eign substances sothe paint surface isnot
scratched ordamaged.
3. Rinse thevehicle thoroughly withplenty ofclean
water.
4. Use adampened chamoistodry the paint surface
and avoid leaving waterspots.
When washing thevehicle, takecare ofthe following:
. Inside flanges, jointsandfolds onthe doors,
hatches andhood areparticularly vulnerabletothe
effects ofroad salt.Therefore, theseareasmust
be cleaned regularly.
. Besure thatthedrain holes inthe lower edgeof
the doors arenot clogged.
. Spray watertothe underbody andinthe wheel
wells toloosen thedirt and/or washawayroad
salt.
REMOVING SPOTS
T32A1308 27-D69C8C6 E-23D2-464A-971C-BACAC 95FCE20
Remove tarand oilspots, industrial dust,insects, and
tree sapasquickly aspossible fromthepaint surface
to avoid lasting damage orstaining. Specialcleaning
products areavailable ataNISSAN dealerorany
automotive accessorystore.
W AXING
T32A130827- D9B96C11-516D-48E7- 8EEB-9F4E4A00E581
Regular waxingprotects thepaint surface andhelps
maintain anew vehicle appearance.
After waxing, polishing isrecommended toremove
built-up residueandtoavoid aweathered appearance.
A NISSAN dealercanassist youinchoosing the
appropriate waxingproducts.
CAUTION:
. Wash yourvehicle thoroughly andcomple-
tely before applying waxtothe paint surface.
. Always followthemanufacturer's instruc-
tions supplied withthewax.
. Donot use awax containing anyabrasives,
cutting compounds orcleaners thatmay
damage thevehicle finish.
Machine compounding oraggressive polishingona
base coat/clear coatpaint finish maydullthefinish or
leave swirlmarks.
GLASS
T32A130 827-EF64A8 17-F9D8-41D 9-9211-AFD2A86FD09E
Use glass cleaner toremove smokeanddust filmfrom
the glass surfaces. Itis normal forglass tobecome
coated withafilm after thevehicle isparked inthe hot
sun. Glass cleaner andasoft cloth willeasily remove
this film.
CLEANING EXTERIOR
&RQGLWLRQ
([FHSWIRU&KLQD