ignition NISSAN X-TRAIL 2017 Manual Online


> (GLW    0RGHO 7$@
T32A1308 27-E3568F A0-1FCD-4E0B-9D9 A-62C1D62A8525
Utility vehicles haveasignificantly higherroll-
over ratethan other types ofvehicles.
They havehigher ground clearance thanpassenger
cars tomake themcapable ofperforming inawide
variety ofon-pavement andoff-road applications. This
gives themahigher center ofgravity thanordinary cars.
An advantage ofhigher ground clearance isabetter
view ofthe road, allowing youtoanticipate problems.
However, theyarenot designed forcornering atthe
same speeds asconventional passengercarsany
more thanlow-slung sportscarsaredesigned to
perform satisfactorily underoff-road conditions. Ifat all
possible, avoidsharp turnsorabrupt maneuvers,
particularly athigh speeds. Aswith other vehicles of
this type, failure tooperate thisvehicle correctly may
result inloss ofcontrol orvehicle rollover.
CAUTION:
. Donot drive ondry hard surface roadsin
LOCK mode.
. Driving ondry hard surface roadsinLOCK
mode maycause unnecessary noiseandtire
wear. NISSAN recommends drivinginthe
2WD orAUT Omode under theseconditions.
(Four-Wheel Drive(4WD) model)
See ªFour-Wheel Drive(4WD)º (P.5-22) formore
details.
T32A1308 27-FAEDCC51-0 3A5-46E8-A1B4-05F8A0ACFCB 0
Driving yourvehicle tofitthe circumstances isessential
for your safety andcomfort. Asadriver, youshould be
the one who knows besthowtodrive inthe given
circumstances.
ENGINE COLDSTART PERIOD
T32A1308 27-423ABF28-182C-45 32-8735-2CF508C400 B5
Due tothe higher engine speeds, whentheengine is
cold, extracaution mustbeexercised whenselecting a
gear during theengine warm-up periodafterstarting
the engine.
L OADING LUGGAGE
T32A130827- F90D098F-7D0F-487B-AF46-661F74A575F1
Loads andtheir distribution andtheattachment of
equipment (couplingdevices,roofluggage carriers,
etc.) willconsiderably changethedriving character-
istics ofthe vehicle. Your driving styleandspeed must
be adjusted according tothe circumstances.
DRIVING INWET CONDITIONS
T32A130827- 9C65E705-D46A-4F87-85ED-94B9DB9A0814
. Avoid accelerating orstopping suddenly.
. Avoid sharpturning orlane changing suddenly.
. Avoid following tooclose tothe vehicle infront.
When watercovers theroad surface withwater
puddles, smallwater streams, etc.,reduce speedto
prevent hydroplaning whichcancause skidding and
loss ofcontrol. Worn tires willincrease thisrisk.
DRIVING INWINTER CONDITIONS
T32A1308 27-707A43B C-7022-449E-80CD-6 02716C03D25
. Drive cautiously .
. Avoid accelerating orstopping suddenly.
. Avoid sharpturning orlane changing suddenly.
. Avoid sudden steering.
. Avoid following tooclose tothe vehicle infront.
T32A130 827-CBF49A 8A-33E0-4B19-A0C4-B073BA66DC FD
WARNING:
Never remove thekey orplace theignition
switch inthe ªLOCKº position whiledriving. The
steering wheelwilllock andcould cause the
driver tolose control ofthe vehicle. Thiscould
result inserious vehicledamage orpersonal
injury.
CONTINUOUSL YVARIABLE TRANSMIS-
SION (CVT)
GUID-605E 0183-46DA-4 BF9-90EB-D63F97C8E 225
JVS0409X
The ignition lockisdesigned sothat theignition switch
cannot beturned tothe ªLOCKº position untiltheshift
lever ismoved tothe ªPº (Park) position. Whenmoving
the ignition switchtothe ªLOCKº position, toremove
the key from theignition switch,makesuretheshift
lever isin the ªPº (Park) position.
When theignition switchcannot beturned tothe
ªL OCKº position:
1. Move theshift lever tothe ªPº (Park) position.
2. Turn theignition switchslightly inthe ªONº
direction.
Starting anddriving
5-7
ON-P
AVEMENT ANDOFF-ROA D
DRIVING PRECAUTIONS CARE
WHEN DRIVING IGNITION
SWITCH(model without
intelligent Keysystem)
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
5-8
Starting anddriving
3. Place theignition switchinthe ªLOCKº position.
4. Remove thekey.
If the ignition switchisturned tothe ªLOCKº position,
the shift lever cannot bemoved fromtheªPº (Park)
position. Theshift lever canbemoved ifthe ignition
switch isin the ªONº position withthefoot brake pedal
depressed.
The ªOFFº position
*
1
is between theªLOCKº and
ªONº positions, althoughitis not marked onthe
ignition switch.
MANUAL TRANSMISSION (MT)
T32A1308 27-AC9B641 D-BD35-4AF4-83C0-7458C9A972 F2
JVS0409X
The ignition switchincludes adevice thathelps
prevent accidental removalofthe key while driving.
The keycan only beremoved whentheignition switch
is in the ªLOCKº position.
1. Turn theignition switchslightly inthe ªONº
direction.
2. Place theignition switchinthe ªLOCKº position.
3. Remove thekey.
The ªOFFº position
*
1
is between theªLOCKº and
ªONº positions, althoughitis not marked onthe
ignition switch.
STEERING LOCK (ifequipped)
T32A1308 27-034768 C7-0064-46 14-AD37-661 7B6EE9A7F
T o lock steering wheel
T32A1308 27-96BC47 46-D027-4F2 F-BE51-24E0 F70F7D7C
1. Place theignition switchinthe ªLOCKº position.
2. Remove thekey,if it is inserted inthe ignition
switch.
3. Turn thesteering wheel1/6ofaturn clockwise
from thestraight upposition.
T o unlock steering wheel
T32A1308 27-238448 DA-E61D-4 230-BDC4-7 65C7822D857
1. Insert thekey into theignition switch.
2. Gently turntheignition switchwhilerotating the
steering wheelslightly rightandleft.
KEY POSITIONS
T32A1308 27-517E0B 80-0FCC-4E 32-84E7-A02 026650916
L OCK (OFF)/L OCK(ACC) (0)
T32A1308 27-1EECA4 4F-6B9C-469F-AD46-0 8410CAFDB 59
. The ignition keycan only beremoved atthis
position.
. Thesteering lock(ifequipped) canonly belocked
at this position.
. The electrical accessory poweractivates without
the engine turnedon.(ACC position)
OFF/OFF(ACC) (1)
T32A1308 27-E0306A2 A-B0CE-4142-9178-4D C58906EEE1
. The engine isturned offwith thesteering wheel
unlocked.
. The electrical accessory poweractivates without
the engine turnedon.(ACC position)
ON (2)
T32A1308 27-99608CE 7-C1A4-419A-AB31-5DED 98FA480D
The ignition systemandtheelectrical accessory power
activate withouttheengine turnedon.
ST ART (3)
T32A130 827-DC8716 CC-7528-494E-8851- 5E7C1C8FB 7AB
The engine starteractivates andtheengine willstart.
The ignition switch,whenreleased, willautomatically
turn tothe ªONº position.
CAUTION:
As soon asthe engine hasstarted, releasethe
ignition switchimmediately.
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
GUID-A467 6F80-7282-4 B00-8821-9F149B55F8E E
PRECAUTIONS ONPUSH-BUTT ONIGNI-
TION SWITCHOPERA TION
GUID-086 E9D42-2B5 5-4695-AC49-9675494A70E1
WARNING:
Do not operate thepush-button ignitionswitch
while driving thevehicle exceptinan emergency.
(The engine willstop when theignition switchis
pushed 3consecutive timesorthe ignition
switch ispushed andheld formore than2
seconds.) Thesteering wheelwilllock andcould
cause thedriver tolose control ofthe vehicle.
This could result inserious vehicledamage or
personal injury.
Before operating thepush-button ignitionswitch,be
sure tomove theshift lever tothe ªPº (Park) position
(for Continuously Variable Transmission model)orthe
shift lever tothe ªNº (Neutral) position(forManual
T ransmission model).
INTELLIGENT KEYSYSTEM
GUID-116 21F56-5195- 4DE6-92E0-5 AFEC5B4DC1F
The Intelligent Key system canoperate theignition
switch without takingthekey outfrom yourpocket or
bag. Theoperating environment and/orconditions may
affect theIntelligent Key system operation. Some
indicators andwarnings foroperation aredisplayed
on the vehicle information displayand/orinthe meter.
(See ªVehicle information displayº(P.2-20) and
ªW arning/indicator lightsandaudible remindersº
(P .2-12) .)
CAUTION:
. Besure tocarry theIntelligent Keywith you
when operating thevehicle.
. Never leavetheIntelligent Keyinside the
vehicle whenyouleave thevehicle. .
Ifthe vehicle battery isdischarged, the
ignition switchcannot beswitched from
the ªLOCKº position, andifthe steering lock
is engaged, thesteering wheelcannot be
moved. Chargethebattery assoon as
possible. (SeeªJump startingº (P.6-8) .)
Operating range
GUID-6DCA9 273-95BE-404D-9DED-C 3ABB1547B7 E
SSD0436
The Intelligent Key can only beused forstarting the
engine whentheIntelligent Key iswithin thespecified
operating range
*
1
.
When theIntelligent Key battery isalmost discharged
or strong radiowaves arepresent neartheoperating
location, theIntelligent Key system's operating range
becomes narrowerandmay notfunction properly.
If the Intelligent Key iswithin theoperating range,itis
possible foranyone, evensomeone whodoes notcarry
the Intelligent Key ,to push theignition switchtostart
the engine.
. The luggage roomareaisnot included inthe
operating range,buttheIntelligent Keymay
function.
. Ifthe Intelligent Key isplaced onthe instrument
panel, insidetheglove box,door pocket orthe
corner ofthe interior compartment, theIntelligent K
ey may notfunction.
. Ifthe Intelligent Key isplaced nearthedoor or
window outsidethevehicle, theIntelligent Key
may function.
Continuously Variable Transmission (CVT)
model
GUID-48 46178B-012D -41FF-8D9A-4 B56BC7ED0EE
The ignition lockisdesigned sothat theignition switch
cannot beswitched tothe ªLOCKº position untilthe
shift lever ismoved tothe ªPº (Park) position.
When theignition switchcannot beswitched tothe
ªL OCKº position:
1. ªShift toParkº warning appears onthe vehicle
information displayandachime sounds.
2. Move theshift lever tothe ªPº (Park) position.
3. Push theignition switch.Theignition switchis
switched tothe ªOFFº position.
4. Open thedoor. Theignition switchturnstothe
ªL OCKº position.
For warnings andindicators onthe vehicle information
display ,see ªVehicle information displayº(P.2-20) .
If the ignition switchisswitched tothe ªLOCKº
position, theshift lever cannot bemoved fromtheªPº
(Park) position. Theshift lever canbemoved ifthe
ignition switchisin the ªONº position withthefoot
brake pedaldepressed.
Starting anddriving
5-9
PUSH-BUT
TON IGNITION SWITCH
(model withIntelligent Keysystem)
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
5-10
Starting anddriving
STEERING LOCK (ifequipped)
GUID-51 E55D68-F23A-4 B9F-922D-FB2A89F4 61A5
The ignition switchisequipped withananti-theft
steering lockdevice.
T o lock steering wheel
GUID-DAE59 353-C43A-4135-85E1 -2B9AABDD5 C86
1. Place theignition switchinthe ªOFFº position
where theignition switchposition indicator willnot
illuminate.
2. Open orclose thedoor. Theignition switchturns
to the ªLOCKº position.
3. Turn thesteering wheel1/6ofaturn tothe right or
left from thestraight upposition.
T o unlock steering wheel
GUID-38F2C6 E2-71BA-4EB6-AD76-1 DA96CF7E0F3
Push theignition switch,andthesteering wheelwillbe
automatically unlocked.
CAUTION:
. Ifthe battery ofthe vehicle isdischarged, the
push-button ignitionswitchcannot be
switched fromtheªLOCKº position.
. Ifthe steering lockrelease malfunction
indicator appearsonthe vehicle information
display, pushtheignition switchagainwhile
rotating thesteering wheelslightly tothe
right andleft.
(See ªVehicle information displayº(P.2-20) .)
IGNITION SWITCHPOSITIONS
GUID-16FB F6ED-49B2- 4CD6-9EF9-8B109D501B 73
WARNING:
Never placetheignition switchinthe ªOFFº
position whiledriving. Thesteering wheelmay
lock andcause thedriver tolose control ofthe
vehicle, resulting inserious vehicledamage or
personal injury.
CAUTION:
. Do not leave thevehicle forextended
periods oftime when theignition switchis
in the ªONº position andtheengine isnot
running. Thiscandischarge thebattery.
. Use electrical accessories withtheengine
running toavoid discharging thevehicle
battery. Ifyou must useaccessories while
the engine isnot running, donot use them
for extended periodsoftime anddonot use
multiple electrical accessories atthe same
time.
JVS0394X
When theignition switchispushed withoutdepressing
the brake pedal (Continuously Variable Transmission model)
orthe clutch pedal(Manual Transmission
model) ,the ignition switchwillilluminate.
Push theignition switchcenter:
. once tochange toªONº .
. twotimes tochange toªOFFº .
The ignition switchwillautomatically returntothe
ªL OCKº position whenanydoor iseither opened or
closed withtheswitch inthe OFF position.
L OCK position
GUID-ED5 510B6-7895-4 E20-81E6-DE8C23CAA8 BB
The ignition switchandsteering lock(ifequipped) can
only belocked atthis position.
The ignition switchwilllock when anydoor isopened
or closed withtheignition switched off.
ON position
GUID-185 3F228-2702- 4CE6-858C-9 045EB728323
The ignition systemandtheelectrical accessory power
activate atthis position withouttheengine turnedon.
The ªONº position hasabattery saverfeature thatwill
place theignition switchinthe ªOFFº position, ifthe
vehicle isnot running, aftersome timeunder the
following conditions:
. alldoors areclosed.
. shift lever isin ªPº (Park) position (CVTmodel) or
ªNº (Neutral) position(MTmodel) .
The battery saverfeature willbecancelled ifany ofthe
following occur:
. anydoor isopened.
. shift lever ismoved outofthe ªPº (Park) position.
. ignition switchchanges position.
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
OFF position
GUID-DA2B 9201-206A-4 06B-891F-59A88D312FBD
The engine isturned offinthis position.
Auto ACC position
GUID-0E2 947FE-3378-4474-91 C2-392C409 08C39
With thevehicle inthe ªPº (Park) position, the
Intelligent Key with youand theignition placedfrom
ªONº toªOFFº ,the radio canstillbeused foraperiod
of time, oruntil thedriver's doorisopened. Aftera
period oftime, functions suchasradio, navigation (if
equipped) ,and Bluetooth


> (GLW    0RGHO 7$@
5-12
Starting anddriving
especially incold weather.
CAUTION:
Do not leave thevehicle unattended whilethe
engine iswarming up.
GUID-85BD 5A32-4CA0-4 B20-A3F7-7F2F8C6EA 88C
1. Apply theparking brake.
2. Continuously Variable Transmission (CVT)
model:
Move theshift lever tothe ªPº (Park) orthe ªNº
(Neutral) position.
The starter isdesigned tooperate onlywhen
the shift lever isin the proper position.
Manual Transmission (MT)model:
Move theshift lever tothe ªNº (Neutral) position.
The starter isdesigned tonot operate unless
the clutch pedalisfully depressed.
The Intelligent Keymust becarried when
operating theignition switch.
3. Place theignition switchinthe ªONº position.
Depress thebrake pedal(CVTmodel) orthe
clutch pedal(MTmodel) andpush theignition
switch tostart theengine.
For diesel engine models: Wait until theglow
indicator light
goes out.
T o start theengine immediately ,push andrelease
the ignition switchwhiledepressing thebrake
pedal orclutch pedalwiththeignition switchin
any position.
4. Immediately releasetheignition switchwhenthe
engine starts.Ifthe engine starts,butfails torun,
repeat theabove procedures.
If the engine isvery hard tostart inextremely cold
or hot weather, depresstheaccelerator pedaland
hold it.Push theignition switchforupto15
seconds whileholding. Release theaccelerator
pedal whentheengine starts.
CAUTION:
. Assoon asthe engine hasstarted, release
the ignition switchimmediately.
. Donot operate thestarter formore than15
seconds atatime. Ifthe engine doesnot
start, place theignition switchinthe ªOFFº
position andwait 10seconds beforecrank-
ing the engine again.Otherwise, thestarter
could bedamaged.
. Ifitbecomes necessary tostart theengine
with abooster batteryandjumper cables,
the instructions andcautions contained in
the ª6.Incase ofemergencyº sectionshould
be carefully followed.
5. Allow theengine toidle foratleast 30seconds
after starting theengine towarm-up. Driveat
moderate speedsforashort distance first,
especially incold weather.
CAUTION:
Do not leave thevehicle unattended whilethe
engine iswarming up.
6. To stop theengine, movetheshift lever tothe ªPº
(Park) position (CVTmodel) ormove theshift lever
to the ªNº (Neutral) position(MTmodel) ,apply the
parking brakeandplace theignition switchinthe
ªOFFº position.
ST ARTING ENGINE (modelwith
Intelligent Keysystem)
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
T32A1308 27-5DFB93F9 -CDD2-40A4-B4CA-7AD 7192119CB
DRIVING WITHCONTINUOUSL YVARI-
ABLE TRANSMISSION (CVT)
T32A1308 27-F7C5B DAC-B708- 41F7-9A32-F14C17BDCD AE
The Continuously Variable Transmission (CVT)inyour
vehicle iselectronically controlledtoproduce maximum
power andsmooth operation.
The recommended operatingprocedures forthis
transmission areshown onthe following pages.Follow
these procedures formaximum vehicleperformance
and driving enjoyment.
WARNING:
Do not downshift abruptlyonslippery roads.
This maycause aloss ofcontrol.
CAUTION:
. The cold engine idlespeed ishigh, souse
caution whenshifting thetransmission into
a forward orreverse position beforethe
engine haswarmed up.
. Avoid revving upthe engine whilethe
vehicle isstopped. Thiscould cause unex-
pected vehicle movement.
. Never shifttoeither theªPº (Park) orªRº
(Reverse) positionwhilethevehicle ismov-
ing. This could cause serious damage tothe
transmission.
. Start theengine ineither theªPº (Park) or
ªNº (Neutral) position.Theengine willnot
start inany other position. Ifitdoes, have
your vehicle checked byaNISSAN dealer.
. Except inan emergency, donot shift tothe
ªNº (Neutral) positionwhiledriving. Coast-
ing with thetransmission inthe ªNº (Neutral)
position maycause serious damage tothe transmission.
. Shift intotheªPº (Park) position andapply
the parking brakewhenatastandstill for
longer thanashort waiting period.
. Keep theengine atidling speed while
shifting fromtheªNº (Neutral) positionto
any driving position.
. When stopping thevehicle onanuphill
grade, donot hold thevehicle bydepressing
the accelerator pedal.Thefoot brake pedal
should bedepressed inthis situation.
Starting vehicle
T32A1308 27-E0E8CE2C -3F3F-496A-B326-0ED705AD3FCB
1. After starting theengine, fullydepress thefoot
brake pedalbefore moving theshift lever outofthe
ªPº (Park) position.
2. Keep thefoot brake pedaldepressed andmove
the shift lever toadriving position.
3. Release theparking brake,thefoot brake pedal,
and then gradually startthevehicle inmotion.
The CVT isdesigned sothe foot brake pedal
MUST bedepressed beforeshifting fromtheªPº
(Park) position toany driving position whilethe
ignition switchisin the ªONº position.
The shift lever cannot bemoved outofthe ªPº
(Park) position andinto anyofthe other
positions ifthe ignition switchisplaced inthe
ªLOCKº ,ªOFFº orªACCº position.
CAUTION:
. DEPRESS THEFOOTBRAKE PEDAL-Shift-
ing the shift lever toªDº ,ªDsº ,ªR º, ªL ºor
manual shiftmode without depressing the
foot brake pedalcauses thevehicle tomove
slowly whentheengine isrunning. Make sure
thefoot brake pedalisdepressed fully
and thevehicle isstopped beforeshifting
the shift lever.
. MAKE SUREOFTHE SHIFT LEVER POSI-
TION -Make suretheshift lever isin the
desired position. ªDº,ªDsº ,ªL ºand manual
shift mode areused tomove forward and
ªR ºto back up.
. WARM UPTHE ENGINE -Due tothe higher
idle speeds whentheengine iscold, extra
caution mustbeexercised whenshifting the
shift lever intothedriving position immedi-
ately afterstarting theengine.
Shifting
GUID-668 83E50-62D B-4D0A-AD 0D-64E18A8 E9465
JVS0391X
With manual shiftmode (LHDmodel) (Type A)
Starting anddriving
5-13
DRIVING
VEHICLE
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
5-14
Starting anddriving
JVS0441X
With manual shiftmode (LHDmodel) (Type B)
SSD0727
Without manualshiftmode (LHD model)
: Push
thebutton
*
A
while depressing the
foot brake
pedal.
: Push
thebutton
*
A
.
: Just
move theshift lever.
WARNING:
. Apply theparking brakeifthe shift lever isin
any position whiletheengine isnot running.
Failure todo socould cause thevehicle to
move unexpectedly orroll away andresult in
serious personal injuryorproperty damage. .
Ifthe shift lever cannot bemoved fromthe
ªPº (Park) position whiletheengine is
running andthefoot brake pedalisde-
pressed, thestop lights maynotwork.
Malfunctioning stoplights couldcause an
accident injuringyourself andothers.
After starting theengine, fullydepress thefoot brake
pedal, pushtheshift lever button andmove theshift
lever outofthe ªPº (Park) position.
If the ignition switchisplaced inthe ªOFFº orªACCº
position forany reason whiletheshift lever isin any
positions otherthantheªPº (Park) position, theignition
switch cannot beplaced inthe ªLOCKº position.
If the ignition switchcannot beplaced inthe ªLOCKº
position, performthefollowing steps:
1. Apply theparking brake.
2. Place theignition switchinthe ªONº position
while depressing thefoot brake pedal.
3. Move theshift lever tothe ªPº (Park) position.
4. Place theignition switchinthe ªLOCKº position.
P (Park) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Use thisposition whenthevehicle isparked orwhen
starting theengine. Makesurethatthevehicle is
completely stoppedandmove theshift lever into
the ªPº(Park) position. Applytheparking brake.
When parking onahill, first depress thefoot brake
pedal, applytheparking brake,andthen move theshift
lever intotheªPº (Park) position.
R (Reverse) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Use thisposition toback up.Make surethatthevehicle
is completely stoppedbeforeselecting theªRº
(Reverse) position. N
(Neutral) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Neither theforward norreverse gearisengaged. The
engine canbestarted inthis position. You may shift to
the ªNº (Neutral) positionandrestart astalled engine
while thevehicle ismoving.
D (Drive) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Use thisposition forallnormal forward driving.
Ds (Drive Sport) (ifequipped) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
When theshift lever isshifted fromtheªDº (Drive) to
ªDsº (Drive Sport) position, thetransmission entersthe
Ds (Drive Sport) mode.Moving theshift lever tothe
ªDsº (Drive Sport) position allowsyoutoenjoy ªsportyº
driving shiftoperation onawinding roadandfeel
smooth acceleration ordeceleration onahilly road by
moving inalower gearautomatically .Moving theshift
lever forwards andbackwards allowsmanual shifting.
When canceling theDs(Drive Sport) mode,returnthe
shift lever tothe ªDº (Drive) position. Thetransmission
returns tothe normal drivingmode.
L (Low) (ifequipped) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Use thisposition whenclimbing steephillsslowly or
driving slowlythrough deepsnow,sand ormud, orfor
maximum enginebraking onsteep downhill grades.
Manual shiftmode
T32A130 827-7DBE3 DA8-E793-455A-A5EF-C 0C301D4126A
When theshift lever isshifted fromtheªDº position to
the manual shiftgate withthevehicle stopped orwhile
driving, thetransmission entersthemanual shiftmode.
Shift ranges canbeselected manually.
In the manual shiftmode, theshift range isdisplayed
on the position indicator inthe meter.
Shift ranges upordown onebyone asfollows:
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
5-16
Starting anddriving
T ype A:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94A EAE0
JVS0392X
Example
1. Place theignition switchinthe ªOFFº orªLOCKº
position.
2. Apply theparking brake.
3. Remove theshift lockrelease cover(shown inthe
illustration above)usingasuitable tool.
4. Insert themechanical keyand push down theshift
lock release.
5. Press theshift lever button andmove theshift
lever tothe ªNº (Neutral) positionwhileholding
down theshift lockrelease. Replace theremoved
shift lockrelease coveraftertheoperation. T
ype B:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94A EAE0
JVS0466X
1. Place theignition switchinthe ªOFFº orªLOCKº
position.
2. Apply theparking brake.
3. Depress theshift lockrelease button.
4. Press theshift lever button andmove theshift
lever tothe ªNº (Neutral) positionwhileholding
down theshift lockrelease.
Place theignition switchinthe ªONº position to
release thesteering wheellock.
The vehicle maybemoved, bypushing, tothe desired
location.
If the shift lever cannot bemoved outofthe ªPº (Park)
position, haveaNISSAN dealerchecktheCVT system
as soon aspossible.
High fluidtemperature protectionmode
T32A1308 27-808BD 7D2-9BE0-4 70E-A660-24 B385D4FB8A
This transmission hasahigh fluidtemperature protec-
tion mode. Ifthe fluid temperature becomestoohigh
(for example, whenclimbing steepgrades inhigh
temperature withheavy loads),engine powerand,
under someconditions, vehiclespeedwillbede-
creased automatically toreduce thechance of
transmission damage.Vehicle speed canbecontrolled with
theaccelerator pedal,butengine andvehicle
speed maybelimited.
Fail-safe
T32A1308 27-5877C8 5B-EA11-4DD 6-9D52-6992317A74D 5
When thefail-safe operation occurs,theCVT willnot
be shifted tothe selected drivingposition.
If the vehicle isdriven underextreme conditions,
such asexcessive wheelspinning andsubse-
quent hardbraking, thefail-safe systemmaybe
activated. Thiswilloccur evenifall electrical
circuits arefunctioning properly.Inthis case,
turn theignition switchoffand wait for10
seconds. Thenplace theignition switchbackin
the ªONº position. Thevehicle shouldreturnto
its normal operating condition. Ifitdoes not
return toits normal operating condition, havea
NISSAN dealercheckthetransmission and
repair itifnecessary.
WARNING:
When thefail-safe operation occurs,vehicle
speed maybegradually reduced.Thereduced
speed maybelower thanother traffic,which
could increase thechance ofacollision. Be
especially carefulwhendriving. Ifnecessary, pull
to the side ofthe road atasafe place andallow
the transmission toreturn tonormal operation,
or have itrepaired ifnecessary.
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
5-18
Starting anddriving
R9M engine model:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
km/h (MPH)
1st 35
(22)
2nd 63
(39)
3rd 98
(61)
4th 136
(85)
5th &6th Ð
(Ð)
GEAR SHIFTINDICA TOR (ifequipped)
GUID-AE4B 246D-E5F4-49 10-9BC9-04131765976 2
JVS0331X
Gear ShiftIndicator appearsinthe vehicle information
display whenthedriver should shiftintoahigher or
lower gearasindicated bythe upordown arrow.
The useofGear ShiftIndicator willhelp toreduce fuel
consumption.
When theuparrow appears, upshifting isrecom-
mended. Whenthedown arrow appears, downshifting
is recommended.
CAUTION:
Gear ShiftIndicator helpstoreduce fuelcon-
sumption. Itdoes notrecommend theappro-
priate gearshiftforalldriving situations. Ina
certain situations, onlythedriver canselect the correct
gear(forexample, whenovertaking,
driving upasteep gradient ortowing atrailer) .
GUID-EB9 25B64-34B7-44CF-8 DDB-6D26A0E20FE2
The Stop/Start SystemorIdling StopSystem is
designed toprevent unnecessary fuelconsumption,
exhaust emissions, andnoise during ajourney:
. When youstop thevehicle withthebrake pedal
depressed (CVT)orwith theshift lever inªNº
(Neutral) andclutch pedalreleased (MT),the
engine isturned offautomatically .
. When yourelease thebrake pedal(CVT) orpush
the clutch pedal(MT),the engine isautomatically
turned on.
CAUTION:
At the end ofthe journey theengine mustbe
stopped andignition turnedoff.Lock thevehicle
as normal. Turning theignition switchOFFwill
shut down allelectrical systems.Failuretodo
this may result inaflat battery.
NO TE:
For model withStop/Start SystemorIdling Stop
System, usethespecial batterythatisenhanced
in regard tothe charge-discharge capacityand
life performance. Avoidusinganon-special
battery forthe Stop/Start SystemorIdling Stop
System, asthis may cause earlydeterioration of
the battery oramalfunction ofthe Stop/Start
System orIdling StopSystem. Forthebattery, it
is recommended touse Genuine NISSANparts.
For more information, contactaNISSAN dealer.
NO TE:
The Stop/Start SystemorIdling StopSystem
will notactivate underthefollowing conditions:
. when theengine iskept idling without any
driving aftertheengine isturned on.
ST OP/ST ARTSY STEM ORIDLING
ST OP SY STEM (ifequippe d)
&RQGLWLRQ
([FHSWIRU&KLQD