engine NISSAN X-TRAIL 2019 Repair Manual


> (GLW    0RGHO 7$@
5-12
Starting anddriving
especially incold weather.
CAUTION:
Do not leave thevehicle unattended whilethe
engine iswarming up.
GUID-85BD 5A32-4CA0-4 B20-A3F7-7F2F8C6EA 88C
1. Apply theparking brake.
2. Continuously Variable Transmission (CVT)
model:
Move theshift lever tothe ªPº (Park) orthe ªNº
(Neutral) position.
The starter isdesigned tooperate onlywhen
the shift lever isin the proper position.
Manual Transmission (MT)model:
Move theshift lever tothe ªNº (Neutral) position.
The starter isdesigned tonot operate unless
the clutch pedalisfully depressed.
The Intelligent Keymust becarried when
operating theignition switch.
3. Place theignition switchinthe ªONº position.
Depress thebrake pedal(CVTmodel) orthe
clutch pedal(MTmodel) andpush theignition
switch tostart theengine.
For diesel engine models: Wait until theglow
indicator light
goes out.
T o start theengine immediately ,push andrelease
the ignition switchwhiledepressing thebrake
pedal orclutch pedalwiththeignition switchin
any position.
4. Immediately releasetheignition switchwhenthe
engine starts.Ifthe engine starts,butfails torun,
repeat theabove procedures.
If the engine isvery hard tostart inextremely cold
or hot weather, depresstheaccelerator pedaland
hold it.Push theignition switchforupto15
seconds whileholding. Release theaccelerator
pedal whentheengine starts.
CAUTION:
. Assoon asthe engine hasstarted, release
the ignition switchimmediately.
. Donot operate thestarter formore than15
seconds atatime. Ifthe engine doesnot
start, place theignition switchinthe ªOFFº
position andwait 10seconds beforecrank-
ing the engine again.Otherwise, thestarter
could bedamaged.
. Ifitbecomes necessary tostart theengine
with abooster batteryandjumper cables,
the instructions andcautions contained in
the ª6.Incase ofemergencyº sectionshould
be carefully followed.
5. Allow theengine toidle foratleast 30seconds
after starting theengine towarm-up. Driveat
moderate speedsforashort distance first,
especially incold weather.
CAUTION:
Do not leave thevehicle unattended whilethe
engine iswarming up.
6. To stop theengine, movetheshift lever tothe ªPº
(Park) position (CVTmodel) ormove theshift lever
to the ªNº (Neutral) position(MTmodel) ,apply the
parking brakeandplace theignition switchinthe
ªOFFº position.
ST ARTING ENGINE (modelwith
Intelligent Keysystem)
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
T32A1308 27-5DFB93F9 -CDD2-40A4-B4CA-7AD 7192119CB
DRIVING WITHCONTINUOUSL YVARI-
ABLE TRANSMISSION (CVT)
T32A1308 27-F7C5B DAC-B708- 41F7-9A32-F14C17BDCD AE
The Continuously Variable Transmission (CVT)inyour
vehicle iselectronically controlledtoproduce maximum
power andsmooth operation.
The recommended operatingprocedures forthis
transmission areshown onthe following pages.Follow
these procedures formaximum vehicleperformance
and driving enjoyment.
WARNING:
Do not downshift abruptlyonslippery roads.
This maycause aloss ofcontrol.
CAUTION:
. The cold engine idlespeed ishigh, souse
caution whenshifting thetransmission into
a forward orreverse position beforethe
engine haswarmed up.
. Avoid revving upthe engine whilethe
vehicle isstopped. Thiscould cause unex-
pected vehicle movement.
. Never shifttoeither theªPº (Park) orªRº
(Reverse) positionwhilethevehicle ismov-
ing. This could cause serious damage tothe
transmission.
. Start theengine ineither theªPº (Park) or
ªNº (Neutral) position.Theengine willnot
start inany other position. Ifitdoes, have
your vehicle checked byaNISSAN dealer.
. Except inan emergency, donot shift tothe
ªNº (Neutral) positionwhiledriving. Coast-
ing with thetransmission inthe ªNº (Neutral)
position maycause serious damage tothe transmission.
. Shift intotheªPº (Park) position andapply
the parking brakewhenatastandstill for
longer thanashort waiting period.
. Keep theengine atidling speed while
shifting fromtheªNº (Neutral) positionto
any driving position.
. When stopping thevehicle onanuphill
grade, donot hold thevehicle bydepressing
the accelerator pedal.Thefoot brake pedal
should bedepressed inthis situation.
Starting vehicle
T32A1308 27-E0E8CE2C -3F3F-496A-B326-0ED705AD3FCB
1. After starting theengine, fullydepress thefoot
brake pedalbefore moving theshift lever outofthe
ªPº (Park) position.
2. Keep thefoot brake pedaldepressed andmove
the shift lever toadriving position.
3. Release theparking brake,thefoot brake pedal,
and then gradually startthevehicle inmotion.
The CVT isdesigned sothe foot brake pedal
MUST bedepressed beforeshifting fromtheªPº
(Park) position toany driving position whilethe
ignition switchisin the ªONº position.
The shift lever cannot bemoved outofthe ªPº
(Park) position andinto anyofthe other
positions ifthe ignition switchisplaced inthe
ªLOCKº ,ªOFFº orªACCº position.
CAUTION:
. DEPRESS THEFOOTBRAKE PEDAL-Shift-
ing the shift lever toªDº ,ªDsº ,ªR º, ªL ºor
manual shiftmode without depressing the
foot brake pedalcauses thevehicle tomove
slowly whentheengine isrunning. Make sure
thefoot brake pedalisdepressed fully
and thevehicle isstopped beforeshifting
the shift lever.
. MAKE SUREOFTHE SHIFT LEVER POSI-
TION -Make suretheshift lever isin the
desired position. ªDº,ªDsº ,ªL ºand manual
shift mode areused tomove forward and
ªR ºto back up.
. WARM UPTHE ENGINE -Due tothe higher
idle speeds whentheengine iscold, extra
caution mustbeexercised whenshifting the
shift lever intothedriving position immedi-
ately afterstarting theengine.
Shifting
GUID-668 83E50-62D B-4D0A-AD 0D-64E18A8 E9465
JVS0391X
With manual shiftmode (LHDmodel) (Type A)
Starting anddriving
5-13
DRIVING
VEHICLE
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
5-14
Starting anddriving
JVS0441X
With manual shiftmode (LHDmodel) (Type B)
SSD0727
Without manualshiftmode (LHD model)
: Push
thebutton
*
A
while depressing the
foot brake
pedal.
: Push
thebutton
*
A
.
: Just
move theshift lever.
WARNING:
. Apply theparking brakeifthe shift lever isin
any position whiletheengine isnot running.
Failure todo socould cause thevehicle to
move unexpectedly orroll away andresult in
serious personal injuryorproperty damage. .
Ifthe shift lever cannot bemoved fromthe
ªPº (Park) position whiletheengine is
running andthefoot brake pedalisde-
pressed, thestop lights maynotwork.
Malfunctioning stoplights couldcause an
accident injuringyourself andothers.
After starting theengine, fullydepress thefoot brake
pedal, pushtheshift lever button andmove theshift
lever outofthe ªPº (Park) position.
If the ignition switchisplaced inthe ªOFFº orªACCº
position forany reason whiletheshift lever isin any
positions otherthantheªPº (Park) position, theignition
switch cannot beplaced inthe ªLOCKº position.
If the ignition switchcannot beplaced inthe ªLOCKº
position, performthefollowing steps:
1. Apply theparking brake.
2. Place theignition switchinthe ªONº position
while depressing thefoot brake pedal.
3. Move theshift lever tothe ªPº (Park) position.
4. Place theignition switchinthe ªLOCKº position.
P (Park) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Use thisposition whenthevehicle isparked orwhen
starting theengine. Makesurethatthevehicle is
completely stoppedandmove theshift lever into
the ªPº(Park) position. Applytheparking brake.
When parking onahill, first depress thefoot brake
pedal, applytheparking brake,andthen move theshift
lever intotheªPº (Park) position.
R (Reverse) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Use thisposition toback up.Make surethatthevehicle
is completely stoppedbeforeselecting theªRº
(Reverse) position. N
(Neutral) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Neither theforward norreverse gearisengaged. The
engine canbestarted inthis position. You may shift to
the ªNº (Neutral) positionandrestart astalled engine
while thevehicle ismoving.
D (Drive) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Use thisposition forallnormal forward driving.
Ds (Drive Sport) (ifequipped) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
When theshift lever isshifted fromtheªDº (Drive) to
ªDsº (Drive Sport) position, thetransmission entersthe
Ds (Drive Sport) mode.Moving theshift lever tothe
ªDsº (Drive Sport) position allowsyoutoenjoy ªsportyº
driving shiftoperation onawinding roadandfeel
smooth acceleration ordeceleration onahilly road by
moving inalower gearautomatically .Moving theshift
lever forwards andbackwards allowsmanual shifting.
When canceling theDs(Drive Sport) mode,returnthe
shift lever tothe ªDº (Drive) position. Thetransmission
returns tothe normal drivingmode.
L (Low) (ifequipped) :
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
Use thisposition whenclimbing steephillsslowly or
driving slowlythrough deepsnow,sand ormud, orfor
maximum enginebraking onsteep downhill grades.
Manual shiftmode
T32A130 827-7DBE3 DA8-E793-455A-A5EF-C 0C301D4126A
When theshift lever isshifted fromtheªDº position to
the manual shiftgate withthevehicle stopped orwhile
driving, thetransmission entersthemanual shiftmode.
Shift ranges canbeselected manually.
In the manual shiftmode, theshift range isdisplayed
on the position indicator inthe meter.
Shift ranges upordown onebyone asfollows:
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
5-16
Starting anddriving
T ype A:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94A EAE0
JVS0392X
Example
1. Place theignition switchinthe ªOFFº orªLOCKº
position.
2. Apply theparking brake.
3. Remove theshift lockrelease cover(shown inthe
illustration above)usingasuitable tool.
4. Insert themechanical keyand push down theshift
lock release.
5. Press theshift lever button andmove theshift
lever tothe ªNº (Neutral) positionwhileholding
down theshift lockrelease. Replace theremoved
shift lockrelease coveraftertheoperation. T
ype B:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94A EAE0
JVS0466X
1. Place theignition switchinthe ªOFFº orªLOCKº
position.
2. Apply theparking brake.
3. Depress theshift lockrelease button.
4. Press theshift lever button andmove theshift
lever tothe ªNº (Neutral) positionwhileholding
down theshift lockrelease.
Place theignition switchinthe ªONº position to
release thesteering wheellock.
The vehicle maybemoved, bypushing, tothe desired
location.
If the shift lever cannot bemoved outofthe ªPº (Park)
position, haveaNISSAN dealerchecktheCVT system
as soon aspossible.
High fluidtemperature protectionmode
T32A1308 27-808BD 7D2-9BE0-4 70E-A660-24 B385D4FB8A
This transmission hasahigh fluidtemperature protec-
tion mode. Ifthe fluid temperature becomestoohigh
(for example, whenclimbing steepgrades inhigh
temperature withheavy loads),engine powerand,
under someconditions, vehiclespeedwillbede-
creased automatically toreduce thechance of
transmission damage.Vehicle speed canbecontrolled with
theaccelerator pedal,butengine andvehicle
speed maybelimited.
Fail-safe
T32A1308 27-5877C8 5B-EA11-4DD 6-9D52-6992317A74D 5
When thefail-safe operation occurs,theCVT willnot
be shifted tothe selected drivingposition.
If the vehicle isdriven underextreme conditions,
such asexcessive wheelspinning andsubse-
quent hardbraking, thefail-safe systemmaybe
activated. Thiswilloccur evenifall electrical
circuits arefunctioning properly.Inthis case,
turn theignition switchoffand wait for10
seconds. Thenplace theignition switchbackin
the ªONº position. Thevehicle shouldreturnto
its normal operating condition. Ifitdoes not
return toits normal operating condition, havea
NISSAN dealercheckthetransmission and
repair itifnecessary.
WARNING:
When thefail-safe operation occurs,vehicle
speed maybegradually reduced.Thereduced
speed maybelower thanother traffic,which
could increase thechance ofacollision. Be
especially carefulwhendriving. Ifnecessary, pull
to the side ofthe road atasafe place andallow
the transmission toreturn tonormal operation,
or have itrepaired ifnecessary.
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
DRIVING WITHMANUAL TRANSMISSION
(MT)
T32A1308 27-F9C2D0 EE-1C88-43FA-80B1 -BC9035D4 5F56
WARNING:
. Donot downshift abruptlyonslippery roads.
This maycause aloss ofvehicle control.
. Donot over-rev theengine whenshifting to
a lower gear.Thismay cause aloss of
vehicle control orengine damage.
CAUTION:
. Donot rest your footonthe clutch pedal
while driving. Thismay damage theclutch
system.
. Fully depress theclutch pedalbefore shift-
ing tohelp prevent transmission damage.
. Stop thevehicle completely beforeshifting
into theªRº(Reverse) position.
. When thevehicle isstopped foraperiod of
time, forexample waitingatstoplights, shift
to the ªNº (Neutral) positionandrelease the
clutch pedalwiththefoot brake pedal
depressed.
. Do not shift tothe ªNº (Neutral) position
while driving. Coasting withthetransmis-
sion inthe ªNº (Neutral) positionmaycause
serious damage tothe transmission.
Starting vehicle
T32A130827- 79841C26-BFA7-47DD-85A1- 81CD1AE3CABD
1. After starting theengine, depress theclutch pedal
to the floor andmove theshift lever tothe ª1º(1st)
or ªRº (Reverse) position.
2. Slowly depress theaccelerator pedal,releasing
the clutch pedalandparking brakeatthe same
time.
Shifting gear
T32A1308 27-BA6FF761 -6916-4D57-ADC5-14 9CCFDB8A1 0
T o change gears,orwhen upshifting ordownshifting,
fully depress theclutch pedal, shiftintotheappropriate
gear, thenslowly andsmoothly releasetheclutch
pedal.
T o ensure smooth gearchanges, fullydepress the
clutch pedalbefore operating theshift lever. Ifthe
clutch pedalisnot fully depressed beforethe
transmission isshifted, agear noise maybeheard.
T ransmission damagecouldoccur.
Start thevehicle inthe ª1º(1st) position andshift to
the ª2º(2nd) ,ª3º (3rd) ,ª4º (4th) ,ª5º (5th) andª6º
(6th) gearinsequence according tothe vehicle speed.
If itis difficult tomove theshift lever intotheªRº
(Reverse) orª1º (1st) position, shifttothe ªNº (Neutral)
position, andthen release theclutch pedalonce.Fully
depress theclutch pedalagainandshift intoªRºorª1º
.
SSD0552
. To back up,stop thevehicle andmove theshift
lever intotheªNº (Neutral) position,andthen pull
the ring
*
1
upward toshift intotheªRº (Reverse)
position.
. The pullring returns toits original position when
the shift lever ismoved tothe ªNº (Neutral)
position.
Suggested maximumspeedineach gear
T32A1308 27-751BC2 BE-4FBE-40E4-87B2-7F6A039719B A
Downshift toalower gearifthe engine isnot running
smoothly ,or ifyou need toaccelerate.
Do not exceed themaximum suggested speed(shown
below) inany gear. Forlevel road driving, usethe
highest gearsuggested forthat speed. Always observe
posted speedlimits,anddrive according tothe road
conditions whichwillensure safeoperation. Donot
over-rev theengine whenshifting toalower gearasit
may cause engine damage orloss ofvehicle control.
MR20DD enginemodel:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
km/h (MPH)
1st 45
(28)
2nd 79
(49)
3rd 110
(68)
4th 143
(89)
5th &6th Ð
(Ð)
Starting anddriving
5-17
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
5-18
Starting anddriving
R9M engine model:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
km/h (MPH)
1st 35
(22)
2nd 63
(39)
3rd 98
(61)
4th 136
(85)
5th &6th Ð
(Ð)
GEAR SHIFTINDICA TOR (ifequipped)
GUID-AE4B 246D-E5F4-49 10-9BC9-04131765976 2
JVS0331X
Gear ShiftIndicator appearsinthe vehicle information
display whenthedriver should shiftintoahigher or
lower gearasindicated bythe upordown arrow.
The useofGear ShiftIndicator willhelp toreduce fuel
consumption.
When theuparrow appears, upshifting isrecom-
mended. Whenthedown arrow appears, downshifting
is recommended.
CAUTION:
Gear ShiftIndicator helpstoreduce fuelcon-
sumption. Itdoes notrecommend theappro-
priate gearshiftforalldriving situations. Ina
certain situations, onlythedriver canselect the correct
gear(forexample, whenovertaking,
driving upasteep gradient ortowing atrailer) .
GUID-EB9 25B64-34B7-44CF-8 DDB-6D26A0E20FE2
The Stop/Start SystemorIdling StopSystem is
designed toprevent unnecessary fuelconsumption,
exhaust emissions, andnoise during ajourney:
. When youstop thevehicle withthebrake pedal
depressed (CVT)orwith theshift lever inªNº
(Neutral) andclutch pedalreleased (MT),the
engine isturned offautomatically .
. When yourelease thebrake pedal(CVT) orpush
the clutch pedal(MT),the engine isautomatically
turned on.
CAUTION:
At the end ofthe journey theengine mustbe
stopped andignition turnedoff.Lock thevehicle
as normal. Turning theignition switchOFFwill
shut down allelectrical systems.Failuretodo
this may result inaflat battery.
NO TE:
For model withStop/Start SystemorIdling Stop
System, usethespecial batterythatisenhanced
in regard tothe charge-discharge capacityand
life performance. Avoidusinganon-special
battery forthe Stop/Start SystemorIdling Stop
System, asthis may cause earlydeterioration of
the battery oramalfunction ofthe Stop/Start
System orIdling StopSystem. Forthebattery, it
is recommended touse Genuine NISSANparts.
For more information, contactaNISSAN dealer.
NO TE:
The Stop/Start SystemorIdling StopSystem
will notactivate underthefollowing conditions:
. when theengine iskept idling without any
driving aftertheengine isturned on.
ST OP/ST ARTSY STEM ORIDLING
ST OP SY STEM (ifequippe d)
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
. when theengine coolant temperature islow.
. when thebattery capacity islow.
. when thebattery temperature islow.
. when thevehicle ismoved.
. when thevacuum inthe brake servode-
creases.
. when theengine hoodisopened withthe
engine running.
. when theengine isturned onwith the
engine hoodopen.
. when thedriver's seatbeltisnot fastened.
. when thedriver's doorisopen.
. when thesteering wheelisoperated (for
CVT model) .
. when theStop/Start orIdling StopSystem
indicator blinksatalow speed.
. when thefan speed control isin any position
other thanªOFFº (0)while theairflow
control isin the front defogger position.
. when thefront defogger switchison.
. when thetemperature insidethevehicle is
too high orlow. (When theairconditioner is
off, theStop/Start SystemorIdling Stop
System willoperate.)
. when thefanspeed ofthe airconditioner is
set tothe maximum speed.
. when theStop/Start orIdling StopOFF
switch isturned on.
. when thepower consumption islarge.
. when thevehicle istraveling ataltitudes
higher than2,000 m(6,562 ft)(for MTmodel) .
. when thevehicle istravelling ataltitudes
higher than1500m (4922ft)(R9M engine in
combination withCVTmodels) . .
For Manual Transmission (MT)models
Ð when theshift lever isin any position
except theªNº(Neutral) position.
Ð when theclutch pedalisdepressed.
Ð when theIntelligent Keyisnot inthe
vehicle.
. For Continuously Variable Transmission
(CVT) models
Ð when theaccelerator pedalisdepressed.
Ð when theshift lever isin the ªRº(Reverse)
position.
Ð when thebrake pedalisnot firmly
depressed.
Ð when stopping thevehicle onsteep
sloping roads.
. when theelectric powersteering warning
light, theAnti-lock BrakingSystem(ABS)
warning light,orthe Vehicle Dynamic Con-
trol (VDC)/Electronic StabilityProgram
(ESP) warning lightilluminates.
NO TE:
The engine willnotrestart evenifthe brake
pedal isreleased (CVT)orclutch pedalis
pressed (MT)while theStop/Start Systemor
Idling StopSystem isactivated underthe
following condition:
. when theshift lever isin the ªPº(Park)
position (CVTmodel) .
. when theengine hoodisopened.
. when thedriver seatbeltisunfastened and
the driver's doorisopened (MTmodel) .
. when thegear shiftlever isnot inthe Neutral
position (MTmodels) . NO
TE:
It may take some timeuntil theStop/Start or
Idling StopSystem activates underthefollowing
conditions:
. when thebattery isdischarged.
. when theoutside temperature islow orhigh.
. when thebattery isreplaced orthe battery
terminal isdisconnected forextended peri-
ods and then reconnected.
NO TE:
When theStop/Start SystemorIdling Stop
indicator illuminates, theengine startsrunning
automatically underatleast oneofthe following
conditions:
. the brake pedalisreleased withtheshift
lever inthe ªDº(Drive) orªNº (Neutral)
position (forCVT model) .
. theshift lever isplaced inthe ªDº(Drive) or
ªRº (Reverse) positionfromtheªNº(Neutral)
or ªPº (Park) position (forCVT model) .
. the driver's seatbeltisunfastened, orthe
driver's doorisopen (forCVT model) .
. the battery voltage becomes low(due to
electrical loadfrom other vehicle systems
like headlights, heaters,etc.,or auxiliary
devices connected tothe 12volt socket
inside thevehicle) .
. the vehicle speedisabove about2km/h (1
MPH) .
. thefront defogger isoperated.
. when thetemperature insidethevehicle is
too high orlow. (When theairconditioner is
off, theStop/Start SystemorIdling Stop
System willoperate.)
Starting anddriving
5-19
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
5-20
Starting anddriving
. when thefront defogger isturned on.(The
engine maynotstarts depending onthe
outside temperature.)
. when morethan3minutes haveelapsed
since theStop/Start SystemorIdling Stop
System wasactive (forCVT model) .
. when theaccelerator pedalisdepressed (for
CVT model) .
. when thesteering wheelisoperated. (The
steering wheeloperation maybecome hea-
vy, but this isnot amalfunction.) (forCVT
model)
. when thebattery capacity islow.
. when thepower consumption ishigh.
. when theshift lever isplaced inthe ªRº
(Reverse) position(forCVT model) .
. when theclutch pedalisdepressed (forMT
model) .
CAUTION:
Only engage gearwhen theclutch pedalisfully
depressed (forMTmodel) .
NO TE:
The following conditions willprevent theStop/
Start System orIdling StopSystem fromauto-
matically restarting theengine. Starting the
engine withtheignition switchoperation isthen
necessary:
. the driver's seatbeltisunfastened, and
driver's doorisopen (forMTmodel) .
. thehood isopen.
Use thissystem whilewaiting atstoplight, etc.When
the vehicle isstopped forlong periods oftime, turnoff
the engine. When
theengine isstopped bythe Stop/Start System
or Idling StopSystem, heating,coolinganddehumi-
difying functions willbedeactivated. To avoid theair
conditioning functionsfrombeing deactivated, turnoff
the Idling Stopmode bypressing theStop/Start or
Idling StopOFFswitch.
ST OP/ST ARTSYSTEM ORIDLING STOP
S YSTEM DISPLA Y
GUID-D5 6CB066-F 6D6-49D2-8 2F7-415D89 07262F
Engine stop
GUID-78FE A13F-8F8D-4B 8D-BC97-67B76FF15 251
JVS0341X
When theengine isstopped theinformation is
displayed forafew seconds.
Stop/Start systemorIdling StopSystem ON
or OFF
GUID-6BC 66795-C2D6 -4F71-9A5B-5ECF0E05 EDF2
JVS0342X
If the Stop/Start SystemorIdling StopSystem is
activated ordeactivated usingtheStop/Start System
or Idling StopSystem OFFswitch, themessage is
shown.
CO2 orfuel saved andengine stoptime
GUID-D9 5A9EFA-4A9B-4 F92-9873-69 DBB336EB8 7
JVS0430X
The CO2 orfuel saved andtheengine stoptimemode
shows thefollowing items:
. The CO2 saved shows theestimated quantityof
CO2 exhaust emissions thatwere prevented by
the Stop/Start SystemorIdling StopSystem every
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
time theengine isautomatically stopped.(for
Europe andSouth Africa)
. The fuelsaved shows theestimated quantityof
fuel that were saved bythe Idling StopSystem
every timetheengine isautomatically stopped.(for
Australia andNew Zealand)
. The engine stoptimeshows thetime thatthe
engine hasbeen stopped forbythe Stop/Start
System orIdling StopSystem.
For more information, seeªStop/Start SystemorIdling
Stop Systemº (P.5-18) .
Auto startdeactivation
GUID-78F50 5B8-38CC-4 27B-9D35-5D4561F762 DD
JVS0344X
If the engine stopswhentheStop/Start Systemor
Idling StopSystem isactivated, andwillnotstart
automatically ,the message isshown.
K ey LOCK warning
GUID-64 20A844-934 9-439B-BBEA -8269875 E380C
JVS0345X
The information isdisplayed andabuzzer sounded to
remind thedriver toturn theignition switchOFFto
avoid aflat battery .
The message canonly becleared byturning or
pushing theignition switchOFF(orrestarting the
engine) .
System fault
GUID-A 7C9F39F-37 0C-4A3E-A35 A-DFC86 7451452
JVS0346X
This message isdisplayed whentheStop/Start
System orIdling StopSystem ismalfunctioning.
Have thesystem checked byaNISSAN dealer.
ST OP/ST ARTORIDLING STOP OFF
SWIT CH
GUID-FF12 3EDF-F41B -49DE-9498 -48D12056 2EA4
JVS0433X
The system canbetemporarily deactivated bypressing
the Stop/Start orIdling StopOFFswitch. Pressing the
switch againorrestarting theengine byusing the
ignition switchwillreactivate theStop/Start Systemor
Idling StopSystem.
. When theStop/Start SystemorIdling Stop
System isdeactivated whiletheengine isrunning,
the engine isprevented fromautomatically stop-
ping.
. When theStop/Start SystemorIdling Stop
System isdeactivated aftertheengine hasbeen
automatically stoppedbythe Stop/Start System
or Idling StopSystem, theengine willimmediately
restart ifsuitable conditions arepresent. The
engine willthen beprevented fromautomatically
stopping duringthesame journey .
. Whenever theStop/Start SystemorIdling Stop
System isdeactivated theindicator light
*
1
on
the Stop/Start orIdling StopOFFswitch illumi-
nates. Inthis condition theStop/Start Systemor
Idling StopSystem cannotprevent unnecessary
fuel consumption, exhaustemissions, ornoise
during yourjourney .
Starting anddriving
5-21
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
4WD mode Wheelsdriven 4WD
mode indicator light (
,
) Use
conditions
2WD Front
wheels:
The wheel drivemode isin
T wo-Wheel Drive(2WD)
when driving onanormal road.
*1 T
urn off For
driving ondry,
paved roads
AUT O Distribution
oftorque tothe
front andrear wheels changes
automatically ,depending on
road conditions encountered
[ratio; 100:0 (2WD) ?50 :
50 (4WD)]. Thisresults in
improved drivingstability . Illuminates
For driving onpaved or
slippery roads
L OCK Four-Wheel
Drive(4WD)
*2*3* Illuminate
/
For driving onrough
roads
*1: The2WD mode maychange tothe 4WD mode automatically dependingonthe driving condition. The4WD
mode indicator lightdoes notilluminate.
*2: TheLOCK mode willchange tothe AUT Omode automatically whenthevehicle hasbeen driven atahigh
speed. The4WD LOCK indicator lightturns off.
*3: TheLOCK mode willautomatically becancelled whentheignition switchisplaced inthe ªOFFº position.
4WD shifttips
T32A130827- 36A0B76C-CF 6C-4546-B388-BD02E B8DB6F1
. Ifthe 4WD mode switch isoperated whilemaking
a turn, accelerating ordecelerating, orifthe
ignition switchisturned offwhile inthe AUT Oor
L OCK mode, youmay feelajolt. This isnormal.
. The oiltemperature ofpower trainparts will
increase ifthe vehicle iscontinuously operated
under conditions wherethedifference inrotation
between thefront andrear wheels islarge (wheel
slip) ,such aswhen driving thevehicle onrough
roads through sandormud orwhen freeing a
stuck vehicle. Inthese cases, theª4WD High
T emp. Stopvehicleº warning appears andthe
4WD mode changes tothe 2WD mode toprotect
the power trainparts. Ifyou stop driving withthe
engine idlinginasafe place andwait until the
ª4WD HighTemp. Stopvehicleº warning disap-
pears, the4WD returns tothe mode previously
selected.
. Brake distance inthe 4WD mode isthe same as
2WD.
CAUTION:
. Depending onthe driving condition, the4WD
mode mayautomatically changefrom2WD
to 4WD even when the2WD mode is
selected. Ifthis occurs whiledriving, the
4WD mode indicator lightwillnotilluminate.
. Donot start theengine withthe4WD mode
switch inany mode inthe following cases:
Ð when thevehicle isplaced onafree-
roller orjacking upthe vehicle withthe
front tiresraised andtherear tires on
the ground.
Starting anddriving
5-23
&RQGLWLRQ
([FHSWIRU&KLQD