reset OLDSMOBILE AURORA 1999 Owners Manual

yellowblue
1-15
3. Just before it reaches the end, give it a quick pull.
4. Let the belt go back all the way. You should hear a
slight clicking sound. If you don't, the adjustment
feature won't set, and you'll have to start again.5. Now you can add a small amount of slack. Lean
forward slightly, then sit back. If you've added more
than 1 inch (25 mm) of slack, pull the shoulder belt
out as you did before and start again.
If you move around in the vehicle enough, or if you pull
out the shoulder belt, the belt will become tight again. If
this happens, you can reset it.
ProCarManuals.com

yellowblue
2-6
Mode 2: All doors automatically lock when shifted out
of PARK (P). Only the driver's door automatically
unlocks when shifted into PARK (P).
Mode 3: All doors automatically lock when shifted out
of PARK (P). All doors automatically unlock when
shifted into PARK (P).
Vehicles are delivered programmed in Mode 3.
To change the modes:
1. Close all doors and turn the ignition on. Keep all
doors closed throughout this procedure.
2. Press and hold the lock position on the driver's
power door lock switch through Step 4.
3. Press the LOCK button on the remote lock control
transmitter. The automatic door locks will remain in
the current mode.
4. Press the LOCK button on the transmitter again.
Each time the transmitter's LOCK button is pressed,
the mode will advance by one, going from Mode 3 to
Mode 0 to Mode 1, etc.
NOTE: The door locks will cycle according to the
mode entered while customizing memory door locks.
(Mode 0 has no feedback.)5. Release the power door lock switch. The
automatic door locks will remain in the most
recent mode selected.
6. Turn the ignition to OFF.
Delayed Locking
This personalization feature lets the driver delay the
actual locking of the vehicle. When the power door lock
switch is pressed with the key removed from the ignition
and the driver's door open, a chime will sound three
times to signal that the lock delay mode is active. When
all doors have been closed, the doors will lock
automatically after five seconds. If any door is opened
before this, the five
-second timer will reset itself once
all the doors have been closed again.
Pressing the door lock switch twice within two seconds
will override this feature.
ProCarManuals.com

yellowblue
2-38
You can set the wiper speed for a long or short delay
between wiper cycles. This can be very useful in light
rain or snow. Push the lever down to the first detent,
DELAY. Turn the band closer to the short lines for fewer
wiper passes per minute. As you turn the band toward
the long lines, the wiper cycles per minute will increase.
Remember that damaged wiper blades may prevent you
from seeing well enough to drive safely. To avoid
damage, be sure to clear ice and snow from the wiper
blades before using them. If they're frozen to the
windshield, carefully loosen or thaw them. If your
blades do become damaged, get new blades or blade
inserts. See ªWindshield Wiper Blade Replacementº in
the Index.
Heavy snow or ice can overload your wipers. A circuit
breaker will stop them until the motor cools. Clear away
snow or ice to prevent an overload.Windshield Washer
The lever on the right side of your steering column also
controls your windshield washer. To spray washer fluid
on the windshield, pull the lever toward you. The wipers
will clear the window and then either stop or return to
your preset speed. For more washer cycles, pull and
hold the lever.
CAUTION:
In freezing weather, don't use your washer until
the windshield is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
If the fluid level in the windshield washer bottle is low,
the message LOW WASHER FLUID will appear in the
Driver Information Center. See ªWindshield Washer
Fluidº in the Index.
ProCarManuals.com

yellowblue
2-41
Resuming a Set Speed
Setting the cruise control at a desired speed and then
applying the brake will end the cruise control function.
Once you're going about 25 mph (40 km/h) or more,
you can briefly move the cruise control switch from ON
to RES/ACC (Resume/Accelerate) to reset. This returns
you to your desired preset speed.
Remember, if you hold the switch at RES/ACC, the
vehicle will accelerate until you release the switch or
apply the brake. So unless you want to go faster, don't
hold the switch at RES/ACC.
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed.

Use the accelerator pedal to go to a higher speed.
Push the button at the end of the lever, then release
the button and the accelerator pedal. You'll now
cruise at the higher speed. Or,

Move the cruise switch from ON to RES/ACC. Hold
it there until you reach a desired speed and then
release the switch. Or, to increase your speed in very
small amounts, move the switch to RES/ACC briefly
and then release it. Each time you do this, your
vehicle will go about 1 mph (1.6 km/h) faster.
The accelerate feature will only work after you have set
the cruise control speed by pushing the SET button.Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:

Push in the button at the end of the lever until you
reach a desired lower speed then release it.

To slow down in very small amounts, push the
button briefly. Each time you do this, you'll go
1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise control speed you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load, and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear to
keep your speed down. Of course, applying the brake takes
you out of cruise control. Many drivers find this to be too
much trouble and don't use cruise control on steep hills.
ProCarManuals.com

yellowblue
2-63 Speedometer
Your speedometer lets you see your speed in both miles
per hour (mph) and kilometers per hour (km/h).
Odometer and Trip Odometer
Your odometer shows how far your vehicle has been
driven in either miles (used in the United States) or
kilometers (used in Canada).
Your trip odometer tells you how far you have driven
since you last reset it. Press the TRIP button located
next to the trip odometer below the fuel gage.
Your vehicle has a tamper resistant odometer. If you see
silver lines between the numbers, you'll know someone
has probably tampered with it and the numbers may not
be true.
You may wonder what happens if your vehicle needs a
new odometer installed. If the new one can be set to the
mileage total of the old odometer, then it must be. But if
it can't, then it's set at zero and a label must be put on
the driver's door to show the old mileage reading when
the new odometer was installed.
ProCarManuals.com

yellowblue
2-68 Anti-Lock Brake System Warning Light
With the anti-lock brake
system, the light(s) will
come on when you start
your engine and may stay
on for several seconds.
That's normal.
If the light stays on, turn the ignition to OFF. Or, if the
light comes on when you're driving, stop as soon as
possible and turn the ignition off. Then start the engine
again to reset the system. If the light still stays on, or
comes on again while you're driving, your vehicle needs
service. If the regular brake system warning light isn't
on, you still have brakes, but you don't have anti
-lock
brakes. If the regular brake system warning light is also
on, you don't have anti
-lock brakes and there's a
problem with your regular brakes. See ªBrake System
Warning Lightº earlier in this section.
The anti
-lock brake system warning light should come
on briefly when you turn the ignition key to RUN. If the
light doesn't come on then, have it fixed so it will be
ready to warn you if there is a problem.
Traction Control System Warning Light
This warning light should
come on briefly as you start
the engine.
If the warning light doesn't come on then, have it fixed
so it will be ready to warn you if there's a problem. If it
stays on, or comes on when you're driving, there may be
a problem with your traction control system and your
vehicle may need service. When this warning light is
on, the system will not limit wheel spin. Adjust your
driving accordingly.
ProCarManuals.com

yellowblue
2-76
Turn on the system by pressing any button except
RESET, ENTER or OFF. When you turn on the ignition,
the DIC will be in the mode last displayed when the
engine was turned off. Keep in mind that this also
applies to the OFF mode.
To turn off messages on the DIC (except LOW OIL
PRESSURE, LOW BRAKE FLUID, PARK BRAKE
SET and the hot engine warnings), press any button on
the DIC.
You will need to open the cover to access the control
buttons. To open the cover, push the button located to
the right of the cover.
To close the cover, push it down to its closed position.
Fuel Economy
The ECON button displays average fuel economy and
instantaneous fuel economy calculated for your specific
driving conditions.
Press ECON to display average fuel economy, such as:
25.2 AVG MI/GAL or 9.3 AVG L/100 KM
Press ECON again to display instantaneous fuel
economy, such as:
28 INST MI/GAL or 8.4 INST L/100 KM
Press again to return to average fuel economy.
The average fuel economy is viewed as a long
-term
approximation of your overall driving conditions.
If you press RESET in this mode while you're driving,
the system will begin figuring fuel economy from that
point in time.
ProCarManuals.com

yellowblue
2-77 Fuel
Press FUEL to see how much fuel has been used since
you last pressed the RESET button. The display will
show a reading such as:
10.4 GALLONS USED or 39.4 LITERS USED
To learn how much fuel will be used from a specific
starting point, first press FUEL to display fuel used,
then press RESET.
Don't confuse fuel used with the amount of fuel in
your tank.
Fuel Range
RANGE calculates the remaining distance you can drive
without refueling. It's based on fuel economy and the
fuel remaining in the tank. The display will show a
reading such as:
FUEL RANGE 235 MI or FUEL RANGE 378 KMIf the range is less than 50 miles (80 km), the display
will read LOW FUEL RANGE.
The fuel economy data used to determine fuel range is
an average of recent driving conditions. As your driving
conditions change, this data is gradually updated.
Resetting fuel range causes the fuel economy data to be
updated immediately. To reset fuel range, press
RANGE, then RESET.
Average Speed
The calculation for average speed begins when SPEED
is reset. Press SPEED to display the average speed,
such as:
AVG SPEED 55 MPH or AVG SPEED 90 KM/H
To reset the average speed, press SPEED and
then RESET.
ProCarManuals.com

yellowblue
2-78 Engine
The ENG button scrolls through the following functions:

Oil pressure, such as:
OIL PRESSURE 40 PSI or OIL PRESSURE
276 kPa

Battery voltage, such as:
BATTERY 13.8 VOLTS

Transaxle fluid life, such as:
TRANS FLUID LIFE 40%
This is an estimate of the transaxle fluid's remaining
useful life. It will show 100% when the system is
reset after a transaxle fluid change. It will alert you
to change your transaxle fluid on a schedule
consistent with your driving conditions.

Engine oil life, such as:
OIL LIFE 30%
This is an estimate of the oil's remaining useful life.
It will show 100% when the system is reset after an
oil change. It will alert you to change your oil on a
schedule consistent with your driving conditions.When the remaining oil life or transaxle fluid life is low,
the system will alert you with a message:
CHANGE OIL SOON or CHANGE TRNS
FLUID SOON
When the oil or transaxle fluid life is down to zero, you
will receive the message:
CHANGE OIL NOW or CHANGE TRNS
FLUID NOW
Always reset the OIL LIFE reminder after an oil change
or the TRNS FLUID LIFE reminder after a transaxle
fluid change. To reset the TRNS FLUID LIFE:
1. With the ignition on, press the ENG button so the
TRNS LIFE percentage is displayed.
2. Press RESET and hold for five seconds. The word
RESET will appear, then TRNS FLUID 100%.
To reset the Oil Life Monitor, see ªEngine Oil Life
Monitorº in the Index. Also, see ªEngine Oil, When to
Changeº in the Index.
ProCarManuals.com

yellowblue
2-79
Remember, you must reset the OIL LIFE or TRNS
FLUID yourself after each oil or transaxle fluid change.
It will not reset itself. Also, be careful not to reset the
OIL LIFE or TRNS FLUID accidentally at any time
other than when the oil or transaxle fluid has just been
changed. It can't be reset accurately until the next oil or
transaxle fluid change.
The DIC does not replace the need to maintain your
vehicle as recommended in the Maintenance Schedule in
this manual. Also, the oil change reminder will not
detect dusty conditions or engine malfunctions that may
affect the oil. If you drive in dusty areas, change your oil
after every 3,000 miles (5 000 km) or three months,
whichever occurs first, unless the DIC instructs you to
do so sooner. Also, the oil change reminder does not
measure how much oil you have in your engine. So, be
sure to check your oil level often. See ªEngine Oilº in
the Index.Check Oil Level Warning
When CHECK OIL LEVEL appears, it indicates that the
engine oil level is 1 to 1 1/2 quarts (0.9 L to 1.4 L) low.
The message will appear only if the engine is running
and it's been at least eight minutes since the engine was
last running. If the message appears, check the oil
dipstick level. If it reads low, your oil level should be
brought up to the proper level (see ªEngine Oilº in the
Index). After bringing the oil to the proper level, the
ignition must be off for eight minutes to allow the
majority of oil to drain into the oil pan.
Distance to Destination
This feature acts as a reverse trip odometer by counting
backward from an estimated distance which you enter
before starting your trip. It also uses that information to
determine the estimated time of arrival.
To set, press DEST, then RESET and enter a maximum
of four digits for the length of your trip. (Always use
whole miles or kilometers.) Then press ENTER. The
system will only accept the last four digits you enter as
your distance to destination.
ProCarManuals.com