radio Oldsmobile Aurora 2001 s Owner's Guide

3-22
All of the CD functions are controlled by the radio
buttons except for ejecting the magazine. Whenever a
CD magazine with discs is loaded in the changer, the
compact disc symbol will appear on the radio display.
If the CD changer is checking the magazine for CDs,
the compact disc symbol will flash on the display until
the changer is ready to play. If CD changer mode is
entered during initialization, LOADING will appear on
the display. When a CD begins playing, a disc and track
number will be displayed. The disc numbers are listed
on the front of the magazine.
Compact Disc Errors
If an error appears on the display, an error has occurred
and the compact disc temporarily cannot play.
The CD changer will send an error message to the
receiver to indicate:

PLAYER OPEN: CD Changer Door Open.
Completely close the door to restore
normal operation.

NO CD'S: CD Changer Cartridge Empty.
Try the magazine again with a disc loaded on
one of the trays.CHECK CD #: If this error message is displayed while
trying to play a CD in the compact disc player or changer,
the following conditions may have caused the error:

The road is too rough. The disc should play when
the road is smoother.

The disc is dirty, scratched, wet or upside down.

The air is very humid. If so, wait about an hour
and try again.
If any error occurs repeatedly or if an error cannot
be corrected, please contact your dealer. If your radio
displays an error number, write it down and provide it
to your dealer when reporting the problem.
Playing a Compact Disc
REV (1): Press and hold this button to quickly reverse
within a track. As the CD reverses, elapsed time will be
displayed with a flashing arrow to help you find the
correct passage.
FWD (2): Press and hold this button to quickly advance
within a track. As the CD advances, elapsed time will be
displayed with a flashing arrow to help you find the
correct passage.

3-23

(3): No function when in CD changer mode.
RDM (4): Press this button to enter the random play
mode. RANDOM ALL will appear on the display.
While in this mode, the tracks on all of the discs will be
played in random order. Press and hold this button to
enter the single
-disc random play mode. RANDOM
ONE will appear on the display and a chime will sound.
Press this button again to turn off the random feature
and return to normal operation.
SIDE (5): Press this button to select the next disc
in the magazine. Each time you press SIDE, the disc
number on the radio display will go to that of the next
available CD.
(6): Press this button to select the previous disc
in the magazine. Each time (6) is pressed, the disc
number on the radio display will go to that of the
previous available CD.
RCL: Press this button to see how long the current
track has been playing. To change what is normally
shown on the display (track or elapsed time), press the
button until you see the display you want, then hold the
button until the display flashes. While elapsed time is
showing, EL TM will appear on the display.SEEK: Press the SEEK reverse arrow while playing a
CD to go back to the start of the current track if more
than eight seconds have played. Press the SEEK forward
arrow and it will go to the next higher track on the disc.
If the button is pressed more than once, the player will
continue moving backward or forward through the disc.
TRACK SCAN: Press and hold one of the SEEK
arrows for two seconds until TRACK SCAN appears
on the display and a chime is heard. The first few
seconds of each track on the current disc will be played.
The sound will mute while scanning. The SCAN icon
will be lit and a ªTº will blink to indicate track scan
mode. Press SEEK again to stop TRACK SCAN.
DISC SCAN: Press and hold one of the SEEK arrows
for four seconds until DISC SCAN appears on the
display and a double chime is heard. The first few
seconds of each disc will be heard. The sound will mute
while scanning. The SCAN icon will be lit and a ªDº
will blink to indicate disc scan mode. Press SEEK again
to stop DISC SCAN.
TP
-CD: Press this button to play a CD if you have a
magazine loaded in the changer and the radio is playing.
To return to the radio while a CD is playing, press
AM
-FM. You can also press this button to switch
between a cassette tape, CD or the CD changer if all
three are loaded.

3-24 Theft-Deterrent Feature
THEFTLOCK
is designed to discourage theft of
your radio. It works by using a secret code to disable
all radio functions whenever battery power is removed
and the radio is placed in a different vehicle. This
feature requires no user input to be activated. It is
automatically armed when it is put into the vehicle for
the first time.
When the radio is turned off, the blinking red light
indicates that THEFTLOCK is armed.
If THEFTLOCK is activated, your radio will not operate
if stolen. The radio will display LOC and a red LED
indicator light will come on above the THEFTLOCK
logo to indicate a locked condition. If this occurs,
the radio will have to be returned to the dealer.
Audio Steering Wheel Controls
With this feature, you can control certain radio functions
using the buttons on your steering wheel.
Some steering wheel
controls operate climate
controls. See ªSteering
Wheel Controls for
Climate Controlº earlier
in this section.
VOL: Press the up or down arrow to increase or
decrease volume.
SEEK: Press this button to tune to the next strong
radio station. When playing a cassette tape or compact
disc, press SEEK to hear the next selection. There must
be at least a three
-second gap between selections on a
cassette tape.
PROG: Press this button to tune in the next preset
radio station. When playing a cassette tape, press PROG
to hear the other side of a tape that is playing. When
listening to a disc in the CD changer, press PROG to
select the next loaded disc.

3-25 Understanding Radio Reception
AM
The range for most AM stations is greater than for FM,
especially at night. The longer range, however, can cause
stations to interfere with each other. AM can pick up
noise from things like storms and power lines. Try
reducing the treble to reduce this noise if you ever get it.
FM Stereo
FM stereo will give you the best sound, but FM signals
will reach only about 10 to 40 miles (16 to 65 km).
Tall buildings or hills can interfere with FM signals,
causing the sound to come and go.
Cellular Phone Usage
Cellular phone usage may cause interference with your
vehicle's radio. This interference may occur when making
or receiving phone calls, charging the phone's battery or
simply having the phone ªonº. This interference is
described as an increased level of static while listening to
the radio. If you notice static while listening to the radio,
unplug the cellular phone and turn it off.
Tips About Your Audio System
Hearing damage from loud noise is almost undetectable
until it is too late. Your hearing can adapt to higher
volumes of sound. Sound that seems normal can beloud and harmful to your hearing. Take precautions by
adjusting the volume control on your radio to a safe
sound level before your hearing adapts to it.
To help avoid hearing loss or damage:

Adjust the volume control to the lowest setting.

Increase volume slowly until you hear comfortably
and clearly.
NOTICE:
Before you add any sound equipment to your
vehicle
-- like a tape player, CB radio, mobile
telephone or two
-way radio -- be sure you can
add what you want. If you can, it's very important
to do it properly. Added sound equipment may
interfere with the operation of your vehicle's
engine, Delphi Delco Electronics radio or other
systems, and even damage them. Your vehicle's
systems may interfere with the operation of sound
equipment that has been added improperly.
So, before adding sound equipment, check with
your dealer and be sure to check Federal rules
covering mobile radio and telephone units.

3-26 Care of Your Cassette Tape Player
A tape player that is not cleaned regularly can cause
reduced sound quality, ruined cassettes or a damaged
mechanism. Cassette tapes should be stored in their
cases away from contaminants, direct sunlight and
extreme heat. If they aren't, they may not operate
properly or may cause failure of the tape player.
Your tape player should be cleaned regularly after
every 50 hours of use. Your radio may display CLEAN
PLAYR to indicate that you have used your tape player
for 50 hours without cleaning and resetting the tape
clean timer. If this message appears on the display,
your cassette tape player needs to be cleaned. It will still
play tapes, but you should clean it as soon as possible to
prevent damage to your tapes and player. If you notice a
reduction in sound quality, try a known good cassette
to see if it is the tape or the tape player at fault. If this
other cassette has no improvement in sound quality,
clean the tape player.The recommended cleaning method for your
cassette tape player is the use of a scrubbing action,
non-abrasive cleaning cassette with pads which scrub
the tape head as the hubs of the cleaner cassette turn.
The recommended cleaning cassette is available through
your dealer (GM Part No. 12344789).
When using a scrubbing action, non
-abrasive cleaning
cassette, it is normal for the cassette to eject because
your unit is equipped with a cut tape detection feature
and a cleaning cassette may appear as a broken tape.
If the cleaning cassette ejects, insert the cassette at least
three times to ensure thorough cleaning.
You may also choose a non
-scrubbing action, wet-type
cleaner which uses a cassette with a fabric belt to clean
the tape head. This type of cleaning cassette will not
eject on its own. A non
-scrubbing action cleaner may
not clean as thoroughly as the scrubbing type cleaner.
The use of a non
-scrubbing action, dry-type cleaning
cassette is not recommended.

3-27
After you clean the player, press and hold EJECT for
five seconds to reset the CLEAN PLAYR indicator.
The radio will display CLEANED to show the indicator
was reset.
Cassettes are subject to wear and the sound quality
may degrade over time. Always make sure the cassette
tape is in good condition before you have your tape
player serviced.
Care of Your Compact Discs
Handle discs carefully. Store them in their original cases
or other protective cases and away from direct sunlight
and dust. If the surface of a disc is soiled, dampen a
clean, soft cloth in a mild, neutral detergent solution
and clean it, wiping from the center to the edge.
Be sure never to touch the signal surface when handling
discs. Pick up discs by grasping the outer edges or the
edge of the hole and the outer edge.
Care of Your Compact Disc Player
The use of CD lens cleaner discs is not advised, due to
the risk of contaminating the lens of the CD optics with
lubricants internal to the CD mechanism.
Diversity Antenna System
Your AM-FM antennas are located in the front
windshield and rear window. Be sure that the inside
surfaces of the front windshield and rear window are
not scratched and that the lines on the glass are not
damaged. If the inside surfaces are damaged, they
could interfere with radio reception. Also, for proper
radio reception, the antenna connector at the top
-center
of the front windshield and the antenna connector at
the top
-center of the rear window need to be properly
attached to the posts on the glass.
NOTICE:
Do not try to clear frost or other material from
the inside of the rear window with a razor blade
or anything else that is sharp. This may damage
the rear defogger grid and affect your radio's
ability to pick up stations clearly. The repairs
wouldn't be covered by your warranty.

3-28
If, when you turn on your rear window defogger, you
hear static on your radio station, it could mean that a
defogger grid line has been damaged. If this is true, the
grid line must be repaired.
If you choose to add an aftermarket cellular telephone to
your vehicle, and the antenna needs to be attached to the
glass, be sure that you do not damage the grid lines for
the AM
-FM antennas or place the cellular telephone
antenna over the grid lines.
Chime Level Adjustment
The volume level of the vehicle's chimes can be
controlled by the radio. To change the volume level,
press and hold pushbutton 6 with the ignition on
and the radio power off. The chime volume level will
change from the normal level to loud, and LOUD will
be displayed on the radio. To change back to the default
or normal setting, press and hold pushbutton 6 again.
The chime level will change from the loud level to
normal, and NORMAL will be displayed.

5-4
1. Check the other vehicle. It must have a 12-volt
battery with a negative ground system.
NOTICE:
If the other system isn't a 12-volt system with a
negative ground, both vehicles can be damaged.
2. Get the vehicles close enough so the jumper cables
can reach, but be sure the vehicles aren't touching
each other. If they are, it could cause a ground
connection you don't want. You wouldn't be able
to start your vehicle, and the bad grounding could
damage the electrical systems.
To avoid the possibility of the vehicles rolling, set
the parking brake firmly on both vehicles involved in
the jump start procedure. Put an automatic transaxle
in PARK (P) and a manual transaxle in NEUTRAL
before setting the parking brake.3. Turn off the ignition on both vehicles. Unplug
unnecessary accessories plugged into the cigarette
lighter or accessory power outlet. Turn off all lamps
that aren't needed as well as radios. This will avoid
sparks and help save both batteries. In addition, it
could save your radio.
4. Open the hoods and locate the other vehicle's battery
and your vehicle's remote positive (+) jump starting
terminal in the box on the passenger side of the
engine compartment. (Your vehicle's battery isn't
under the hood.)
CAUTION:
An electric fan can start up even when the engine
is not running and can injure you. Keep hands,
clothing and tools away from any underhood
electric fan.

6-68 Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses and circuit
breakers. This greatly reduces the chance of fires caused
by electrical problems.
Look at the silver
-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical size
and rating. If a MaxiFuse

should blow, see your dealer
for service immediately.
If you ever have a problem on the road and don't have a
spare fuse, you can ªborrowº one that has the same
amperage. Pick some feature of your vehicle that you
can get along without
-- like the radio or cigarette
lighter
-- and use its fuse, if it is the correct amperage.
Replace it as soon as you can. You will find a fuse puller
clipped in both of the bussed electrical centers. Snap the
wide end of the fuse puller at the side indentations and
pull the fuse out.
The MaxiFuses are located in two Bussed Electrical
Centers (BEC), one located near the engine compartment
on the passenger's side and the other under the rear seat on
the driver's side. If a MaxiFuse should blow, have your
vehicle serviced by your dealer immediately.Engine Compartment Bussed Electrical Center (BEC)
The front Bussed Electrical
Center (BEC) is located in
the front of the engine
compartment on the
passenger's side. Lift the
cover to gain access. See
ªEngine Compartment
Overviewº in the Index
for more information
on location.
Fuse 22 or 23 can be moved to the outer position to
provide continuous power to the accessory power outlet
or cigarette lighter when the ignition is not ON.
See your dealer for additional assistance, if needed.
Leaving an accessory on for a long period of time can
drain the vehicle's battery.