climate control Oldsmobile Aurora 2001 Owner's Manuals

2-33
Engine Exhaust
CAUTION:
Engine exhaust can kill. It contains the gas
carbon monoxide (CO), which you can't see or
smell. It can cause unconsciousness and death.
You might have exhaust coming in if:

Your exhaust system sounds strange
or different.

Your vehicle gets rusty underneath.

Your vehicle was damaged in a collision.

Your vehicle was damaged when driving over
high points on the road or over road debris.

Repairs weren't done correctly.

Your vehicle or exhaust system had been
modified improperly.
If you ever suspect exhaust is coming into
your vehicle:

Drive it only with all the windows down to
blow out any CO; and

Have your vehicle fixed immediately.
Running Your Engine While
You're Parked
It's better not to park with the engine running. But if you
ever have to, here are some things to know.
CAUTION:
Idling the engine with the climate control
system off could allow dangerous exhaust into
your vehicle. See the earlier Caution under
ªEngine Exhaust.º
Also, idling in a closed-in place can let deadly
carbon monoxide (CO) into your vehicle even if
the fan switch is at the highest setting. One place
this can happen is a garage. Exhaust
-- with
CO
-- can come in easily. NEVER park in a
garage with the engine running.
Another closed-in place can be a blizzard.
See ªBlizzardº in the Index.

2-63
The main components of your instrument panel are:
A. Air Outlet
B. Turn Signal/Multifunction Lever
C. Steering Wheel Controls for Climate Control System
D. Steering Wheel Controls for Audio System
E. Windshield Wiper/Washer Control
F. Driver Information Center (DIC)
G. Hazard Warning Flasher Button
H. Climate Control System
I. Instrument Panel Brightness ControlJ. Trip Odometer Buttons
K. Hood Release
L. Parking Brake
M. Cruise Control Lever
N. Ignition Switch
O. Audio System
P. Accessory Power Outlet
Q. Glove Box (Trunk Release Lockout Switch inside)

2-69 Battery Warning Light
This light will come on
briefly when you start the
vehicle, as a check to show
you it is working; then it
should go out.
If it stays on, or comes on while you are driving, you
may have a problem with the electrical charging system.
It could indicate that you have a generator problem or
another electrical system problem. Have it checked
right away. Driving while this light is on could drain
your battery.
If you must drive a short distance with the light on, be
certain to turn off all your accessories, such as the radio
and climate control system.
On the DIC a CHECK CHARGE SYSTEM message
will be displayed and a warning chime will sound.
See ªDIC Warnings and Messagesº in the Index
for more information.
Brake System Warning Light
Your vehicle's hydraulic brake system is divided into
two parts. If one part isn't working, the other part can
still work and stop you. For good braking, though, you
need both parts working well.
If the warning light comes on, there is a brake problem.
Have your brake system inspected right away.
United States Canada
This light should come on briefly when you turn the
ignition key to RUN. If it doesn't come on then, have it
fixed so it will be ready to warn you if there's a problem.
If the light comes on while you are driving, pull off the
road and stop carefully. You may notice that the pedal is
harder to push. Or, the pedal may go closer to the floor.
It may take longer to stop. If the light is still on, have the
vehicle towed for service. See ªTowing Your Vehicleº
in the Index.

2-78
Driver Information Center (DIC)
The Driver Information Center (DIC) displays
information in either English or metric. When the
system is on or off, push the ON/OFF button down
for three seconds to change the display between English
and metric. This will also change the digital screen for
the climate control system between English and metric.The DIC has different display modes which can be
accessed by pressing the four buttons on the DIC.
These buttons are labeled ON/OFF, SELECT right
arrow, SELECT down arrow and RESET. The button
functions are detailed in the following.
Turn on the system by pressing the ON/OFF button
once. When you turn on the ignition, the DIC will be in
the mode last displayed when the engine was turned off.
Keep in mind that this also applies to the OFF mode.
To turn off messages on the DIC (except LOW OIL
PRESSURE, LOW BRAKE FLUID, PARK BRAKE
SET, STARTING DISABLED and the HOT...STOP
ENGINE warning), press the RESET button.
Pressing the SELECT right arrow button will allow
you to access the following modes, DATE/ET, FUEL,
ECON, OIL and GAGE. While in any of these modes,
warning messages can interrupt and take over the
display until you acknowledge the message, or the
condition causing the problem goes away.

3-
3-1
Section 3 Comfort Controls and Audio Systems
In this section, you'll find out how to operate the comfort control and audio systems offered with your vehicle.
Be sure to read about the particular systems supplied with your vehicle.
3
-2 Comfort Controls
3
-2 Automatic Electronic Climate Control
3
-6 Air Conditioning
3
-7 Heating
3
-7 Defogging and Defrosting
3
-8 Rear Window Defogger
3
-8 Passenger Temperature Control (Option)
3
-9 Ventilation System
3
-10 Steering Wheel Controls for Climate Control
3
-10 Audio Systems
3
-10 Setting the Clock3
-11 AM-FM Stereo with Cassette Tape and
Compact Disc Player with Programmable
Equalization and Radio Data System (RDS)
3
-20 Trunk-Mounted CD Changer (Option)
3
-24 Theft-Deterrent Feature
3
-24 Audio Steering Wheel Controls
3
-25 Understanding Radio Reception
3
-25 Tips About Your Audio System
3
-26 Care of Your Cassette Tape Player
3
-27 Care of Your Compact Discs
3
-27 Care of Your Compact Disc Player
3
-27 Diversity Antenna System
3
-28 Chime Level Adjustment

3-2
Comfort Controls
This section tells you how to operate your climate
control system.
Your vehicle may be equipped with a passenger
compartment air filter. For more information, see
ªPassenger Compartment Air Filterº in the Index.
Comfort Controls Personalization
(If Equipped)
This feature allows two different drivers to store and
recall their own climate control settings for temperature,
air delivery mode and fan speed. The personal choice
settings recalled are determined by the transmitter used
to enter the vehicle. After the button with the unlock
symbol on a remote keyless entry transmitter is pressed,
and the ignition is in RUN, the climate control will
adjust to the last settings of the identified driver. The
settings can also be changed by pressing one of the
memory buttons (1 or 2) located on the driver's door,
until you hear two beeps. When adjustments are made,
the new settings are automatically saved for that driver.
Automatic Electronic Climate Control
Your vehicle is equipped with either a Single Zone or
a Dual Zone Automatic Electronic Climate Control
System. You can use the automatic setting or override
the automatic setting by using the manual controls.
Your vehicle also has the flow
-through ventilation
system described later in this section.
AUTO
-PUSH Knob
By pressing the AUTO
-PUSH knob, you have
selected the electronic climate control system to be in
the automatic mode. The climate control system will
automatically control the air temperature, air inlets, air
distribution and the fan speed based on your selected
temperature setting as well as on the temperature inside
the vehicle, the outside temperature and the sun load.

3-3

When you press the AUTO-PUSH knob, the lights
under the AUTO
-PUSH and AUTO FAN knobs
will illuminate. Your current comfort setting will be
shown in the digital display.

Set the comfort level you want inside the vehicle by
using the colored buttons located below the climate
control display.

Turn the AUTO
-PUSH knob to select the
manual air delivery mode operation of the climate
control system.
Temperature Buttons
To adjust the comfort level you want maintained inside
the vehicle, use the red and blue buttons located below
the digital display. If you want a warmer comfort level,
push the red button. If you want a cooler comfort level,
push the blue button. Your selected comfort setting will
be shown on the digital display for five seconds, then
the outside temperature will be displayed.Mode Control
Turn the AUTO
-PUSH knob to deliver air through
the floor, panel or windshield outlets. The system will
stay in the selected mode until the AUTO
-PUSH knob
is pressed.
AUTO FAN Knob
This knob controls the fan speed in either an automatic
mode or a manual mode.

Pressing the AUTO FAN knob puts the fan control
in the automatic mode. The AUTO FAN light will
appear below the knob. The fan speed indicators
will not be illuminated when the system is in the
automatic fan control mode.

Turning the AUTO FAN knob selects a manual
fan speed. Turn this knob clockwise to raise the fan
speed. Turn this knob counterclockwise to lower the
fan speed. Turning the AUTO FAN knob overrides
the automatic fan control mode. The fan speed
indicators will be illuminated while in the manual
fan control mode.

3-4
Automatic Operation
Press the AUTO
-PUSH knob when you want the
system to automatically adjust the interior temperature
to your preference. When the system is set for automatic
operation, air will come from the floor, the panel outlets
or the windshield outlets depending on the temperature
inside the vehicle, the outside temperature, the engine
coolant temperature and the sun load. Fan speed will
vary as the system reaches and maintains the comfort
setting you have selected.
To find your comfort setting, start with the system in
automatic mode by pressing the AUTO
-PUSH knob.
Adjust the comfort setting by using the red and blue
buttons located below the digital display until you
reach a setting of 75
F (24
C) on the display. Give the
vehicle about 30 minutes to stabilize and then readjust
the comfort setting if necessary. The display will show
the comfort setting for five seconds and then it will
show the outside temperature.In cold weather, the system will delay turning on the
fan to avoid blowing cold air. The length of the delay
depends on the engine coolant temperature and the
outside temperature. Turning the AUTO FAN knob
will override this delay by turning off the automatic fan
mode and changing the fan speed.
Your automatic electronic climate control system has a
sun sensor located on the top of the instrument panel
that detects direct sunlight. To keep you and your
passengers comfortable, the system may supply cooler
air to the side toward the sun. Be careful not to put
anything over this sun sensor. The automatic electronic
climate control system may not operate correctly if this
sensor is covered.
To change the automatic electronic climate control
display from an English display to a metric display,
push the OFF button located in the Driver Information
Center (DIC) for two seconds. The display in the DIC
will also change from an English to a metric display. To
return to an English display, repeat the above procedure.

3-5
Manual Operation
You may override the automatic airflow distribution by
turning the AUTO
-PUSH knob. After you turn this
knob, the comfort setting will be displayed for five
seconds, then the outside temperature will be displayed.
The fan control will remain in the automatic control
mode unless you turn the AUTO FAN knob to select
a manual fan speed.
PANEL: This setting directs airflow through the
upper air outlets located in the instrument panel.
BI-LEVEL: This setting directs the airflow
through both the panel air outlets and the lower floor
outlets. There is also a small amount of air directed to
the front defroster and the side window defrosters.
FLOOR: This setting directs most of the airflow
to the lower floor outlets with some airflow directed to
the side window defrosters. There is also a small amount
of airflow directed to the front defroster.
DEFOG: This setting directs the majority of
the airflow to the lower floor outlets and the front
defroster. A small amount of airflow is directed to the
side window defroster outlets. This mode can be useful to remove the moisture from the inside of the windshield
when the outside temperature is cold or the humidity is
high. Be sure the A/C indicator light comes on to allow
the air compressor to come on automatically to help
dehumidify the air.
DEF (Defrost): This setting directs the majority
of the airflow to the windshield with some airflow to
the side window defrosters and lower floor outlets.
To increase the fan speed, turn the AUTO FAN knob
clockwise. If defrost is selected from AUTO mode,
your automatic electronic climate control system will
automatically increase the defrost outlet temperature
and fan speed. For maximum front defrost performance
under extreme icing or frosting conditions, increase the
temperature setting to 90
F (33
C) and increase
the fan speed to high.
Even though A/C is not selected, in front defrost
mode the A/C compressor will run automatically
at temperatures over approximately 40
F (4
C) to
improve windshield clearing performance. This
dehumidifies the air to help dry the windshield.
Even though the compressor may be running,
the A/C indicator light will not come on in front
defrost unless you select A/C.

3-10 Steering Wheel Controls for Climate Control
Some heating and cooling
controls can be adjusted
at the steering wheel.
Other touch controls
also operate some audio
controls. See ªAudio
Steering Wheel Controlsº
later in this section.
Press the upper part of the fan symbol button to override
the automatic fan control and increase the fan speed.
Press the lower part of the fan symbol button to override
the automatic fan control and reduce the fan speed.
Press either arrow on the TEMP button once to display
your current comfort setting in the digital display. Press
the upper part of the TEMP button again to provide a
warmer comfort setting or press the lower part of the
TEMP button again to provide a cooler comfort setting.
Audio Systems
Your audio system has been designed to operate easily
and give years of listening pleasure. You will get the
most enjoyment out of it if you acquaint yourself with it
first. Find out what your audio system can do and how
to operate all its controls, to be sure you're getting the
most out of the advanced engineering that went into it.
Setting the Clock
Press and hold HR until the correct hour appears. The
letters AM or PM will appear on the display. Then, press
and hold MN until the correct minute appears. The clock
may be set with the ignition on or off. In addition, the
clock can also be automatically set, when tuned to an
RDS station that is broadcasting time, by pressing and
holding the HR and the MN button at the same time.
The display will show TIME UPDATED. If there is no
time available, NO UPDATE will be displayed.