mirror controls Oldsmobile Aurora 2001 Owner's Manuals

Table of Contents
Keys and Door Locks
Remote Lock Control
Trunk Release
Automatic Transaxle
Parking Brake
Windows
Tilt Wheel
Turn Signal/Multifunction Lever
Windshield Wipers
Cruise Control
Interior and Exterior LampsMirrors
Storage Compartments
Convenience Net
Accessory Power Outlet
OnStar® System (If Equipped)
Sunroof (Option)
HomeLink® Transmitter (If Equipped)
Instrument Panel, Warning Lights and Gages
Driver Information Center
Memory and Personalization Seats and Seat Controls
Safety BeltsAir Bag Systems
Child Restraints
Section
1
Section
2
Seats and Restraint Systems
Features and Controls
ii

1-4 Memory Seat and Mirrors (If Equipped)
If your vehicle has this
feature, the controls on
the driver's door panel
are used to program and
recall previous settings.
You can use this feature to save your driver's seat
position, lumbar adjustment, outside mirror positions,
personalization features, comfort controls and
radio settings.Adjust the driver's seat (including the lumbar
adjustments) and both outside mirrors to the position
you would like for driving. Then press and hold memory
button 1 for more than three seconds. A double beep
will sound when the memory is set.
To set the seat and mirror positions for a second driver,
follow the previous steps, but press button 2 instead.
You can also store an exit position for each driver. The
exit position is programmed by moving the seat to the
desired exit position and then holding the exit button for
more than three seconds. The exit position set will be for
the most recently selected driving position (1 or 2).
Please note that mirror and lumbar positions will not be
stored or recalled for the exit position.

1-5
To recall your memory positions, your vehicle must be in
PARK (P). Push and release the memory button (1 or 2)
corresponding to the desired driving position. The seat and
mirrors will move to the position previously stored for the
identified driver. You will hear one beep.
To recall the exit position, your vehicle must be in
PARK (P). Push and release the EXIT button and the
seat will move to the exit position previously stored for
the current identified driver. You will hear one beep.
If an exit position has not been stored for the current
identified driver, the seat will move all the way back.
To stop recall movement of the seat at any time, press
one of the power seat controls located on the outboard
side of each front seat.
If you would like your stored driving or exit position
to be recalled when unlocking your vehicle with the
transmitter, see ªDIC Personalizationº in the Index.Heated Front Seat (Option)
The heated seat controls
are located next to the
console shifter.
Push the ON part of the button once for a HI setting or
twice for a LO setting. Push the OFF part of the button
to turn the heated seat off. The LO setting warms the
seatback and cushion until the seat approximates body
temperature. The HI setting heats the seatback and
cushion to a slightly higher temperature.
The heated seats can only be used when the ignition
is turned on. The heating elements in the seats
automatically turn off when the vehicle's ignition is
turned off.

2-
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything
is working properly
-- and what to do if you have a problem.
2
-2 Windows
2
-4 Keys
2
-6 Door Locks
2
-9 Remote Lock Control
2
-14 Trunk
2
-16 Theft
2
-17 Universal Theft-Deterrent
2
-18 PASS-Key
III
2
-20 New Vehicle ªBreak-Inº
2
-21 Ignition Positions
2
-22 Starting Your Engine
2
-25 Engine Coolant Heater (If Equipped)
2
-26 Automatic Transaxle Operation
2
-29 Parking Brake
2
-30 Shifting Into PARK (P)
2
-32 Shifting Out of PARK (P)2
-32 Parking Over Things That Burn
2
-33 Engine Exhaust
2
-34 Tilt Wheel
2
-35 Turn Signal/Multifunction Lever
2
-44 Exterior Lamps
2
-46 Interior Lamps
2
-50 Mirrors
2
-53 Storage Compartments
2
-56 Accessory Power Outlet
2
-56 OnStar
System (If Equipped)
2
-57 Sunroof (Option)
2
-58 HomeLink
Transmitter (If Equipped)
2
-62 The Instrument Panel - Your
Information System
2
-66 Warning Lights, Gages and Indicators
2
-78 Driver Information Center (DIC)

2-50
Mirrors
Electrochromic Day/Night Rearview Mirror
with Compass
Your vehicle has an electrochromic inside rearview
mirror with a compass. Your vehicle's mirror may also
contain OnStar

controls.
This is the on/off button for mirrors equipped
with OnStar controls.
Pressing the MIRROR button (or the on/off button for
mirrors equipped with OnStar controls) located at the
bottom of the mirror, turns the automatic dimming
feature on or off.
The mirror also includes an eight
-point compass display
in the upper right corner of the mirror face. When on, the
compass automatically calibrates as the vehicle is driven.
When cleaning the mirror, use a paper towel or similar
material dampened with glass cleaner. Do not spray
glass cleaner directly on the mirror as that may cause
the liquid cleaner to enter the mirror housing.Mirror Operation
To turn on the automatic dimming feature, press MIRROR
(or press and hold the on/off button for about three seconds
for mirrors equipped with OnStar controls). To turn off
automatic dimming, press MIRROR (or press and hold
the on/off button for about three seconds for mirrors
equipped with OnStar controls) again. The green indicator
light will be illuminated when this feature is active.
The automatic dimming feature will be active each time
the vehicle is started.
Compass Operation
Press COMPASS (or the on/off button for mirrors equipped
with OnStar controls) once to turn the compass on or off.
When the ignition and the compass feature are on, the
compass will show two character boxes for approximately
two seconds. After two seconds, the mirror will display the
compass heading.
Compass Calibration
If after two seconds, the display does not show a compass
heading (ªNº for North, for example), there may be a
strong magnetic field interfering with the compass. Such
interference may be caused by a magnetic antenna mount,
magnetic note pad holder or a similar magnetic item.
If the letter ªCº should ever appear in the compass
window, the compass may need calibration.

2-51
The mirror can be calibrated in one of two ways:

Drive the vehicle in circles at 5 mph (8 km/h) or
less until the display reads a direction, or

drive the vehicle on your everyday routine.
Mirrors equipped with OnStar controls can be placed in
calibration mode by pressing and holding the on off
button until a ªCº is shown in the compass display.
Compass Variance
The mirror is set in zone eight upon leaving the factory.
It will be necessary to adjust the compass to compensate
for compass variance if you live outside zone eight.
Under certain circumstances, as during a long distance
cross
-country trip, it will be necessary to adjust for
compass variance. Compass variance is the difference
between earth's magnetic north and true geographic
north. If not adjusted to account for compass variance,
your compass could give false readings.
To adjust for compass variance:
1. Find your current location and variance zone number
on the following zone map.
2. Press and hold COMPASS (or the on/off button for
mirrors equipped with OnStar controls) until a zone
number appears in the display.
3. Once the zone number appears in the display, press
the COMPASS (or the on/off button for mirrors
equipped with OnStar controls) button quickly until
the correct zone number appears in the display.
Stop pressing the button and the mirror will
return to normal operation. If ªCº appears in the
compass window, the compass may need calibration.
See ªCompass Calibrationº explained previously.

2-52 Power Remote Control Mirror
The controls on the driver's door operate both outside
rearview mirrors. Move the L/R switch to the left (L)
to select the driver's side rearview mirror, or to the
right (R) to select the passenger's side rearview mirror.
Then press the arrows on the four
-way pad to adjust
each mirror so that you can see a little of the side of
your vehicle when you are sitting in a comfortable
driving position.Leave the L/R switch in the center position to disable
mirror movement by the four
-way control pad.
If your vehicle is equipped with the memory function,
the mirrors and driver's seat position, can be stored into
memory. See ªMemory Seat and Mirrorsº in the Index.
Parallel Park Assist Mirror (If Equipped)
If you have the memory seat and mirrors feature,
the passenger's outside rearview mirror also includes a
tilt
-down feature that operates when the shift lever is
in REVERSE (R). When the vehicle is shifted out of
REVERSE (R), the passenger mirror will return to its
original position after a five
-second delay. This delay
prevents movement of the mirror if multiple gear
transitions (REVERSE (R) to DRIVE (D) to
REVERSE (R)) occur during a parallel parking
maneuver. This feature can be programmed on or off
through the DIC. See ªDriver Information Centerº
or ªPersonalization Featuresº in the Index for
programming instructions. Vehicles are delivered
with this feature off.

2-84
The DIC is used to program the personal choices of
two drivers. The drivers are recognized as DRIVER 1
and DRIVER 2. You will let the DIC and the vehicle
know which driver you are by using your remote lock
control transmitter or by pressing the appropriate
memory seat control button located on the driver's door
or choosing the driver with the DIC. Each remote lock
control transmitter was pre
-programmed to belong to
DRIVER 1 or DRIVER 2. The personalization features
may be programmed differently for each driver.
When you press the unlock symbol on the transmitter,
the DIC will automatically change driver numbers and the
vehicle will recall the personal choice settings that were
last made to correspond to your transmitter, including
your radio and comfort control settings. See ªComfort
Controls, Personalizationº in the Index.
If you unlock the vehicle using your door key instead
of your transmitter, the personal choice settings will
correspond to the previous driver of the vehicle as
identified by a transmitter, a memory seat control or
through the DIC. If this happens and you were not
the last driver of the vehicle, press your correct driver
number on the memory seat controls, press the
unlock symbol on your transmitter or select the
personalization programming mode and choose the
correct driver number.After you have the correct driver number on the display
use the SELECT down arrow button to scroll through
the following messages and feature options:

DOORS LOCK IN GEAR
- YES/NO

DOORS UNLOCK
- YES/NO

ALL DOORS IN PARK
- YES/NO

ALL DOORS AT KEY OFF
- YES/NO

DRIVERS DOOR IN PARK
- YES/NO

DRIVERS DOOR KEY OFF
- YES/NO

PASS WINDOW LOCKOUT
- YES/NO

KEY FOB FLASH LIGHTS
- YES/NO

KEY FOB CHIRP HORN
- YES/NO

DELAY LOCK OF DOORS
- YES/NO

PERIMETER LIGHTS
- YES/NO

EXT LIGHT TIMEOUT
- 25

DISPLAY DRIVER ID
- YES/NO

KEY FOB MEMORY SEAT
- YES/NO

DRIVING POSITION
- YES

EXIT POSITION
- YES

TILT MIRROR REVERSE
- YES/NO