start stop button Oldsmobile Aurora 2001 Owner's Manuals

2-59
Your vehicle's engine should be turned off while
programming the transmitter. Follow these steps to
program up to three channels:
1. If you have previously programmed a transmitter
channel, proceed to Step 2. Otherwise, hold
down the two outside buttons on the HomeLink
Transmitter until the indicator light begins to flash
rapidly (after 20 seconds). Then release the buttons.
This procedure initializes the memory and erases any
previous settings for all three channels.
2. Decide which one of the three channels you want to
program. Hold the end of the hand
-held transmitter
about 2 to 5 inches (5 to 13 cm) away from the
surface of the HomeLink Transmitter so that you
can still see the indicator light.
3. Using both hands, press the hand
-held transmitter
button and the desired button on the HomeLink
Transmitter. Continue to press both buttons
through Step 4.
4. Hold down both buttons until you see the indicator
light on the HomeLink Transmitter flash slowly and
then rapidly. The rapid flashing indicates that the
HomeLink Transmitter has been programmed.
Release both buttons once the indicator light starts
to flash rapidly.If you have trouble programming the HomeLink
Transmitter, make sure that you have followed the
directions exactly as described. The HomeLink
Transmitter may not work with older garage door openers
that do not meet current Federal Consumer Safety
Standards. If you cannot program the transmitter after
repeated attempts, refer to ªRolling Code Programmingº
later in this section or contact the HomeLink Transmitter
manufacturer at 1
-800-355-3515.
Be sure to keep the original hand
-held transmitter
in case you need to erase and reprogram the
HomeLink Transmitter.
Note to Canadian Owners: During programming,
the hand
-held transmitter may automatically stop
transmitting after one or two seconds. In this case, you
should press and repress the button on the hand
-held
transmitter every two seconds without ever releasing the
button on the HomeLink Transmitter. Release both
buttons when the indicator light on the HomeLink
Transmitter begins to flash rapidly.

2-71 Traction Control System Warning Light
This warning light should
come on briefly as you
start the engine.
If the warning light doesn't come on then, have it fixed
so it will be ready to warn you if there's a problem. If it
stays on, or comes on when you're driving, there may be
a problem with your traction control system and your
vehicle may need service. When this warning light is on,
the system will not limit wheel spin. Adjust your
driving accordingly.
The traction control system warning light may come
on for the following reasons:

If you turn the system off by pressing the TC button
located on the center console, the warning light will
come on and stay on. To turn the system back on,
press the button again. The warning light should go
off. See ªTraction Control Systemº in the Index
for more information.
If there's a brake system problem that is specifically
related to traction control, the traction control
system will turn off and the warning light will come
on. If your brakes begin to overheat, the traction
control system will turn off and the warning light
will come on until your brakes cool down.

If the traction control system is affected by an
engine
-related problem, the system will turn off
and the warning light will come on.
If the traction control system warning light comes on
and stays on for an extended period of time when the
system is turned on, your vehicle needs service.
Traction Control System Active Light
When your traction control
system is limiting wheel
spin, this light will come on.
Slippery road conditions may exist if the traction
control system active light comes on, so adjust your
driving accordingly.
The light will stay on for a few seconds after the traction
control system stops limiting wheel spin.

2-78
Driver Information Center (DIC)
The Driver Information Center (DIC) displays
information in either English or metric. When the
system is on or off, push the ON/OFF button down
for three seconds to change the display between English
and metric. This will also change the digital screen for
the climate control system between English and metric.The DIC has different display modes which can be
accessed by pressing the four buttons on the DIC.
These buttons are labeled ON/OFF, SELECT right
arrow, SELECT down arrow and RESET. The button
functions are detailed in the following.
Turn on the system by pressing the ON/OFF button
once. When you turn on the ignition, the DIC will be in
the mode last displayed when the engine was turned off.
Keep in mind that this also applies to the OFF mode.
To turn off messages on the DIC (except LOW OIL
PRESSURE, LOW BRAKE FLUID, PARK BRAKE
SET, STARTING DISABLED and the HOT...STOP
ENGINE warning), press the RESET button.
Pressing the SELECT right arrow button will allow
you to access the following modes, DATE/ET, FUEL,
ECON, OIL and GAGE. While in any of these modes,
warning messages can interrupt and take over the
display until you acknowledge the message, or the
condition causing the problem goes away.

2-79 Date/Elapsed Time
Pressing the SELECT down arrow while in DATE/ET
mode will allow you to choose between the elapsed time
and date menus.
Date
To set the date, press and hold the RESET button for
two seconds while the date is being displayed on the
DIC. When the date set mode is entered the display
will show the following:
YEAR?_____ MM/DD/00
The year will be flashing. To increase the item that is
flashing press SELECT right arrow. To decrease the
item that is flashing press SELECT down arrow.
When you reach the current year press the RESET
button. The DIC will ask for the month. The month
will flash the same as the year. Use the SELECT
buttons to reach the current month and press RESET.
The DIC will then ask for the day. The day will flash the
same as the year. Use the SELECT buttons to reach the
current day. Press the RESET button again and the set
display will stop flashing and go back to the normal
operation mode.Elapsed Time (ET)
When the ignition is on, the DIC can be used as a
stopwatch. The display will show hours and minutes.
The elapsed time indicator will record up to 100 hours,
then it will reset to zero and continue counting. Press
SELECT down arrow while in the DATE/ET mode,
and the display will show the amount of time that has
elapsed since the elapsed time indicator was last reset
(not including time the ignition is off), such as:
01:08 ELAPSED TIME
To start or stop the counting of time, press the RESET
button briefly. If the colon (:) in the time is flashing,
time is being counted. Time is displayed in hours and
minutes. Seconds are not displayed. Time will continue
to be counted as long as the ignition is on, even if
another display is being shown on the DIC.
To reset elapsed time to zero, press RESET button
for three seconds while the elapsed time is displayed.

2-90 DIC Warnings and Messages
Other messages or warnings may appear in the DIC
display. For Canadian drivers, in addition to the DIC
message your DIC will display EXP with a number after
it which reflects the following messages:
EXP (Export ID) Warning Message. . . . . . . . . . . .
1 AIR BAG PROBLEM. . . . . . . . . . . . . . . . . . . . . .
2 CHANGE OIL NOW. . . . . . . . . . . . . . . . . . . . . . .
3 CHANGE OIL SOON. . . . . . . . . . . . . . . . . . . . . .
4 CHECK CHARGE SYSTEM. . . . . . . . . . . . . . . . .
5 CHECK OIL LEVEL. . . . . . . . . . . . . . . . . . . . . . .
6 TRANS HOT...IDLE ENG. . . . . . . . . . . . . . . . . . .
7 CONFIRM TIME & DATE. . . . . . . . . . . . . . . . . .
8 DRIVERS DOOR AJAR. . . . . . . . . . . . . . . . . . . .
9 ENGINE HOT...A/C OFF. . . . . . . . . . . . . . . . . . .
10 HOT...REDUCE ENG RPM. . . . . . . . . . . . . . . . .
11 HOT...STOP ENGINE *. . . . . . . . . . . . . . . . . . . .
12 THEFT SYSTEM FAULT. . . . . . . . . . . . . . . . . .
13 LEFT REAR DOOR AJAR. . . . . . . . . . . . . . . . .
14 LOW BRAKE FLUID *. . . . . . . . . . . . . . . . . . . .
15 LOW ENGINE COOLANT. . . . . . . . . . . . . . . . .
16 LOW FUEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 LOW OIL PRESSURE *. . . . . . . . . . . . . . . . . . .
18 LOW TIRE PRESSURE. . . . . . . . . . . . . . . . . . .
19 LOW WASHER FLUID. . . . . . . . . . . . . . . . . . . .
20 PARK BRAKE SET *. . . . . . . . . . . . . . . . . . . . .
21 PASSENGER DOOR AJAR. . . . . . . . . . . . . . . .
22 RIGHT REAR DOOR AJAR. . . . . . . . . . . . . . . .
23 SERVICE VEHICLE SOON. . . . . . . . . . . . . . . .
24 TURN SIGNAL ON?. . . . . . . . . . . . . . . . . . . . . .
25 THEFT ATTEMPTED. . . . . . . . . . . . . . . . . . . . .
26 SERV STABILITY SYS. . . . . . . . . . . . . . . . . . . .
27 HEADLAMPS SUGGESTED. . . . . . . . . . . . . . .
28 TRUNK AJAR. . . . . . . . . . . . . . . . . . . . . . . . . . .
29 BATTERY SAVER ACTIVE. . . . . . . . . . . . . . . .
32 HOT...IDLE ENGINE. . . . . . . . . . . . . . . . . . . . .
33 STARTING DISABLED *. . . . . . . . . . . . . . . . . .
36 CHECK GAS CAP. . . . . . . . . . . . . . . . . . . . . . . .
42 STABILITY ACTIVE. . . . . . . . . . . . . . . . . . . . .
The EXP codes are used to make translation from
English to other languages easier.
Pressing the RESET button will remove the above
messages or warnings from the DIC display, unless
noted by an asterisk (*).

3-15
ALERT!: This type of announcement warns of national
or local emergencies. You will not be able to turn off
alert announcements. ALERT! appears on the display
when an alert announcement plays. When an alert
announcement comes on the tuned radio station, you
will hear it, even if the volume is muted or a cassette
tape or compact disc is playing. If the cassette tape or
compact disc player is playing, play will stop for the
announcement and resume when the announcement
is finished.
ALTERNATE FREQUENCY: This feature allows
the radio to switch to a stronger station with the same
broadcast. Press and hold AM
-FM for two seconds to
turn alternate frequency on. AF ON will appear on the
display. The radio may switch to stronger stations with
the same broadcast. Press and hold AM
-FM again for
two seconds to turn alternate frequency off. AF OFF
will appear on the display. The radio will not switch to
other stations. When you turn the ignition off and
then on again, the alternate frequency feature will
automatically be turned on.Adjusting the Speakers
BAL
-FADE: The AUDIO button adjusts balance and
fade. To adjust balance, press and hold the AUDIO
button until BAL appears on the display. Turn the knob
to adjust the sound to the left or right speakers. The
middle position balances the sound between the speakers.
To adjust fade, press and hold the AUDIO button until
FAD appears on the display. Turn the knob to adjust the
sound to the front or rear speakers. The middle position
balances the sound between the speakers.
Playing a Cassette Tape
Your tape player is built to work best with tapes that are
up to 30 to 45 minutes long on each side. Tapes longer
than that are so thin they may not work well in this
player. The longer side with the tape visible should face
to the right. If the ignition is on, but the radio is off, the
tape can be inserted and will begin playing. If you hear
nothing but a garbled sound, the tape may not be in
squarely. Press EJECT to remove the tape and start over.

3-23

(3): No function when in CD changer mode.
RDM (4): Press this button to enter the random play
mode. RANDOM ALL will appear on the display.
While in this mode, the tracks on all of the discs will be
played in random order. Press and hold this button to
enter the single
-disc random play mode. RANDOM
ONE will appear on the display and a chime will sound.
Press this button again to turn off the random feature
and return to normal operation.
SIDE (5): Press this button to select the next disc
in the magazine. Each time you press SIDE, the disc
number on the radio display will go to that of the next
available CD.
(6): Press this button to select the previous disc
in the magazine. Each time (6) is pressed, the disc
number on the radio display will go to that of the
previous available CD.
RCL: Press this button to see how long the current
track has been playing. To change what is normally
shown on the display (track or elapsed time), press the
button until you see the display you want, then hold the
button until the display flashes. While elapsed time is
showing, EL TM will appear on the display.SEEK: Press the SEEK reverse arrow while playing a
CD to go back to the start of the current track if more
than eight seconds have played. Press the SEEK forward
arrow and it will go to the next higher track on the disc.
If the button is pressed more than once, the player will
continue moving backward or forward through the disc.
TRACK SCAN: Press and hold one of the SEEK
arrows for two seconds until TRACK SCAN appears
on the display and a chime is heard. The first few
seconds of each track on the current disc will be played.
The sound will mute while scanning. The SCAN icon
will be lit and a ªTº will blink to indicate track scan
mode. Press SEEK again to stop TRACK SCAN.
DISC SCAN: Press and hold one of the SEEK arrows
for four seconds until DISC SCAN appears on the
display and a double chime is heard. The first few
seconds of each disc will be heard. The sound will mute
while scanning. The SCAN icon will be lit and a ªDº
will blink to indicate disc scan mode. Press SEEK again
to stop DISC SCAN.
TP
-CD: Press this button to play a CD if you have a
magazine loaded in the changer and the radio is playing.
To return to the radio while a CD is playing, press
AM
-FM. You can also press this button to switch
between a cassette tape, CD or the CD changer if all
three are loaded.