OLDSMOBILE BRAVADA 1994 Owners Manual
Page 131 of 248
1 Driving in the Rain 
Rain and wet roads can  mean driving 
trouble.  On a wet  road  you  can’t  stop, 
accelerate or  turn  as well because  your 
tire-to-road traction  isn’t  as good  as  on 
dry  roads.  And, if your  tires  don’t  have 
much tread  left,  you’ll  get  even  less 
traction.  It’s always  wise  to go  slower 
and  be cautious 
if rain  starts  to fall 
while  you  are driving.  The surface  may 
get  wet suddenly  when your reflexes  arc 
tuned  for driving  on dry  pavement.  The 
heavier  the rain, the harder  it  is to 
see.  Even 
if your  windshield  wiper  blades 
are  in  good  shape, a  heavy  rain  can make 
it harder  to see  road  signs  and traffic 
signals,  pavement  markings,  the edge 
of 
the road, and  even  people  walking. 
It’s  wise  to keep  your  wiping  equipment 
in  good  shape and  keep  your  windshield 
washer tank  filled.  Replace  your 
windshield  wiper  inserts when they 
show  signs 
of streaking  or  missing  areas 
on the windshield, or  when strips of 
rubber  start  to  separate  from the inserts. 
I 
Driving  too fast through  large water 
puddles or  even  going  through  some  car 
washes  can cause  problems,  too. The 
water  may  affect  your  brakes. Try 
to 
avoid puddles.  But if you can’t,  try to 
slow  down  before  you  hit them. 
125 
ProCarManuals.com 
Page 132 of 248
Your Driving and the Road 
126 
Hydroplaning 
Hydroplaning is dangerous.  So  much 
water  can build  up  under  your tires  that 
they can actually ride  on  the  water. This 
can happen 
if the  road  is wet enough 
and  you’re  going fast enough.  When 
your  vehicle  is  hydroplaning,  it  has little 
or  no  contact  with  the  road. 
Hydroplaning  doesn’t happen often. 
But  it can 
if your tires haven’t  much 
tread  or 
if the pressure  in  one or more  is 
low.  It can happen 
if a lot  of water  is 
standing  on  the  road. 
If you  can see 
reflections 
horn trees,  telephone poles, 
or  other  vehicles,  and  raindrops 
“dimple”  the water’s surface,  there 
could  be hydroplaning. 
Hydroplaning  usually  happens at higher 
speeds.  There just isn’t a  hard and fast 
rule  about  hydroplaning.  The best advice 
is  to 
slow down  when  it is  raining. 
Some  Other  Rainy  Weather Tips 
Turn on your  low-beam  headlights - 
not just your parking  lights - to help 
make  you  more visible  to others. 
Besides  slowing down,  allow some 
extra following  distance. And  be 
especially  careful  when  you  pass 
another  vehicle. Allow  yourself  more 
clear  room  ahead,  and  be prepared  to 
have your  view restricted  by road 
spray. 
Have  good tires with proper tread 
depth.  (See 
Tires in  the Index.) 
A , ” 
I City Driving 
One  of the  biggest  problems with  city 
streets  is the  amount 
of traffic  on  them. 
You’ll  want 
to watch  out for what  the 
other  drivers  are doing  and pay 
attention  to  traffic signals. 
Here  are ways  to increase your  safety  in 
city  driving: 
Know  the best  way to get  to where 
you  are going.  Get a city  map  and 
plan your  trip  into  an  unknown part 
of  the  city  just  as  you  would  for a 
cross-country trip. 
ProCarManuals.com 
Page 133 of 248
Try to use  the freeways  that rim and 
crisscross most  large cities.  You'll 
save  time  and energy.  (See the next 
section, 
Freeway Driving.) 
signal. A traffic  light  is there  because 
the  corner  is  busy  enough  to need  it. 
When a  light turns  green, and just 
before 
YOU start  to  move, check both 
ways  for vehicles  that have  not 
cleared  the intersection or  may  be 
running  the  red light. 
Treat a green  light as a warning 
Freeway Driving 
Mile  for mile,  freeways  (also called 
thruways, parkways,  expressways, 
turnpikes,  or superhighways) are  the 
safest  of all  roads.  But they  have  their 
own  special  rules. 
The most  important  advice on freeway 
driving 
is: Keep  up with  traffic and keep 
to  the  right. Drive  at  the  same speed 
most  of the  other  drivers are driving. 
Too-fast  or  too-slow  driving  breaks a 
smooth  traffic  flow.  Treat the left lane 
on  a freeway  as a passing  lane. 
At  the  entrance  there  is usually  a ramp 
that  leads  to  the  freeway. 
If you  have  a 
clear  view  of the  freeway  as you  drive 
along  the  entrance  ramp, 
you should  begin 
to check  traffic.  Try  to determine 
where  you  expect  to blend  with the 
flow.  Try  to merge  into  the  gap at close 
to  the  prevailing  speed. Switch 
on your 
turn  signal,  check  your  mirrors and 
glance  over  your  shoulder as often  as 
necessary.  Try  to blend  smoothly  with 
the  traffic  flow. 
Once  you are on  the  freeway,  adjust 
your  speed  to  the posted  limit  or  to  the 
prevailing  rate if it's  slower.  Stay 
in the 
right lane unless  you want  to  pass. 
Before  changing  lanes, check  your 
mirrors. Then use  your turn signal. 
Just  before  you  leave  the lane,  glance 
quicldy  over  your  shoulder to make  sure 
there  isn't  another  vehicle in your 
"blind"  spot. 
Once  you are moving 
on the  freeway, 
make certain  you  allow a reasonable 
following  distance. Expect to move 
slightly  slower  at night. 
When  you want  to leave  the freeway, 
move  to  the  proper lane  well  in 
advance. 
If you  miss  your exit  do not, 
under  any circumstances,  stop and back 
up.  Drive 
on to  the  next exit. 
127 
ProCarManuals.com 
Page 134 of 248
Your Driving und the Road 
128 
The exit ramp can be curved,  sometimes 
quite  sharply. 
The  exit  speed  is  usually  posted. 
Reduce  your  speed  according  to your 
speedometer,  not to your  sense  of 
motion.  After  driving  for  any  distance  at 
higher  speeds,  you  may  tend to think  you 
are  going  slower  than you  actually  are. 
I Before  Leaving on a  Long 
Tip 
Make sure  you’re  ready. Try to be  well 
rested.  If 
you must start  when  you’re 
not  fresh 
- such  as after  a  day’s  work 
- don’t  plan  to make  too many  miles 
that  first part  of the  journey.  Wear 
comfortable  clothing  and shoes you can 
easily  drive  in. 
Is  your  vehicle  ready  for a  long  trip? If 
you  keep  it serviced  and maintained, it’s 
ready  to go. 
If it needs  service,  have  it 
done  before  starting  out. 
Of course, 
you’ll  find  experienced  and able  service 
experts  in Oldsmobile  dealerships all 
across North  America.  They’ll  be  ready 
and  willing  to help  if you  need  it. 
Here are some things  you  can  check 
before  a  trip: 
Windshield  Washer  Fluid Is the 
reservoir  full?  Are all windows  clean 
inside  and outside? 
shape? 
you  checked  all  levels? 
Wiper  Blades: Are  they  in  good 
Fuel,  Engine Oil, Other  Fluids: Have 
Lights: Are they  all  working?  Are the 
lenses  clean? 
Tires: They  are vitally  important  to a 
safe,  trouble-free  trip. Is the tread 
good  enough  for  long-distance 
driving?  Are  the tires  all  inflated  to 
the  recommended pressure? 
Weather  Forecasts: What’s  the 
weather outlook  along  your route? 
Should  you  delay  your  trip a short 
time  to avoid  a  major  storm system? 
Maps: Do you  have  up-to-date maps? 
Highway  Hypnosis 
Is there  actually  such a condition  as 
“highway  hypnosis”? Or  is it just  plain 
falling  asleep  at  the wheel?  Call  it 
highway  hypnosis,  lack 
of awareness,  or 
whatever. 
There  is  something  about an easy 
stretch  of road  with  the same  scenery,  along 
with the  hum  of the  tires on  the 
road,  the drone  of the  engine,  and the 
rush  of the  wind  against  the vehicle  that 
can make  you  sleepy.  Don’t  let it 
happen 
to you!  If it does,  your  vehicle 
can  leave  the road  in 
less than a 
second, and  you  could  crash and be 
injured. 
What can  you do about  highway 
hypnosis?  First, be  aware  that  it can 
happen. 
Then here are some tips: 
Make  sure your  vehicle  is  well 
ventilated, with  a  comfortably  cool 
interior. 
Keep  your  eyes  moving.  Scan the road 
ahead and  to  the sides.  Check  your 
mirrors and  your instruments 
frequently. 
If  you  get  sleepy,  pull off the  road  into 
a  rest,  service,  or  parking  area and 
take  a nap,  get some  exercise,  or both. 
For  safety,  treat drowsiness  on  the 
highway  as  an emergency. 
ProCarManuals.com 
Page 135 of 248
Hill and Mountain Roads 
Driving on steep  hills or mountains  is 
different  from  driving 
in flat or rolling 
terrain. 
If you  drive  regularly  in  steep  country, 
or 
if you’re  planning  to visit  there,  here 
are  some  tips  that  can  make your trips 
safer  and more  enjoyable.  (See 
Off- 
Road Driving in  the Index for 
information  about driving  off-road.) 
Keep  your  vehicle  in good  shape. 
Check 
all fluid  levels  and also  the 
brakes,  tires,  cooling  system  and 
transmission.  These parts  can  work 
hard  on  mountain  roads. 
how  how  to go down hills. The most 
important  thing  to how  is this:  let 
your  engine  do some 
of the  slowing  down. 
Shift to 
a lower  gear  when you 
go 
down a  steep  or  long  hill. 
Know  how  to go  uphill. You may 
want  to shift 
down to a lower  gear. 
The  lower  gears  help  cool  your  engine 
and  transmission,  and you  can climb 
the  hill better. 
Stay  in  your own lane when  driving on 
two-lane  roads in hills  or mountains. 
Don’t  swing  wide  or cut  across  the 
center  of the  road.  Drive  at speeds  that 
let  you  stay  in  your 
own lane. 
As you  go  over  the  top of a hill,  be 
alert.  There  could  be  something  in 
your  lane,  like a stalled  car or an 
accident. 
You may  see  highway  signs  on 
mountains  that  warn  of special 
problems.  Examples  are long  grades, 
passing  or no-passing  zones,  a falling 
rocks  area, or winding  roads. Be alert 
to  these  and tale  appropriate  action. 
129 
ProCarManuals.com 
Page 136 of 248
Your Driving and the Road 
130 
Winter Driving 
Here are some  tips for winter  driving: 
Have  your  Oldsmobile  in good  shape 
for  winter.  Be sure  your  engine 
coolant  mix  is  correct. 
You  may  want to put winter 
emergency  supplies  in your  vehicle. 
Include  an ice  scraper, 
a small  brush or 
broom, 
a supply  of windshield  washer 
fluid, 
a rag,  some  winter outer clothing, 
a  small  shovel,  a  flashlight,  a  red  cloth, 
and  a  couple  of reflective  warning 
triangles.  And, if you  will  be driving 
under  severe  conditions,  include  a  small 
bag  of sand,  a  piece  of old  carpet or  a 
couple 
of burlap  bags to help  provide 
traction.  Be sure  you  properly  secure 
these  items  in your  vehicle. 
Driving  on Snow  or Ice 
Most  of the  time,  those  places  where 
your  tires  meet  the road  probably  have 
good  traction. 
However, 
if there  is  snow  or ice 
between  your  tires  and the road,  you 
can  have  a  very  slippery  situation. 
You’ll  have  a  lot less  traction or “grip” 
and  will  need  to be  very  careful. 
What’s  the worst  time  for  this? “Wet 
ice.”  Very  cold  snow  or ice  can be  slick 
and hard  to drive  on. But  wet  ice can  be 
even  more  trouble because  it may  offer 
the  least  traction  of all.  You  can get 
“wet  ice” when  it’s about  freezing 
(32°F; 0.C) and freezing  rain begins  to 
fall.  Try  to avoid  driving  on wet  ice  until 
salt  and  sand  crews  can get there.  Whatever 
the condition 
- smooth  ice, 
packed,  blowing  or loose  snow 
- drive 
with  caution. 
Accelerate  gently.  Try  not to break  the 
fragile  traction.  If you  accelerate  too fast, 
the  drive  wheels  will  spin  and  polish  the 
surface  under  the tires  even  more. 
Your  anti-lock  brakes  improve  your  ability  to make  a  hard  stop on 
a slippery 
road.  Even though  you have  an anti-lock 
braking  system,  you’ll  want to begin 
stopping  sooner  than you  would  on dry 
pavement.  See 
Anti-Lock in the Index. 
Allow  greater  following  distance on 
any  slippery  road. 
Watch for  slippery  spots. The road 
might  be fine  until  you  hit a spot 
that’s  covered  with ice. On  an 
otherwise  clear  road, ice  patches  may 
appear in shaded areas where  the  sun 
can’t  reach:  around clumps  of trees, 
behind  buildings,  or  under bridges. 
Sometimes  the surface  of a  curve  or 
an  overpass  may remain  icy when  the 
surrounding  roads are clear. 
If you  see 
a patch  of ice  ahead  of you,  brake 
before  you are on it. Try  not to brake 
while  you’re  actually  on  the ice, and 
avoid  sudden  steering  maneuvers. 
ProCarManuals.com 
Page 137 of 248
If You’re Caught in a Blizzard 
If you are stopped  by heavy  snow,  you 
could  be  in  a  serious  situation. 
You 
should  probably  stay with your  vehicle 
unless  you  know for sure  that you are 
near  help  and you  can  hike  through the 
snow.  Here are some  things to do  to 
su~nmon  help and keep  yourself  and 
your  passengers  safe:  Turn on your 
hazard  flashers.  Tie  a  red cloth  to your 
vehicle  to alert  police  that you’ve  been 
stopped  by the  snow.  Put on extra 
clothing  or  wrap a  blanket  around you. 
If 
you  have  no blankets  or extra clothing, 
make  body  insulators from  newspapers, 
burlap  bags,  rags,  floor  mats 
- anything 
you  can  wrap around  yourself  or tuck 
under 
your clothing  to keep  warm. 
You  can run  the  engine to keep  warm, 
but  be  careful. 
~ .--- . . .. . . .. ~  ~ ~, L 
Run  your  engine  only  as long  as you 
must. This  saves  fuel.  When 
you run the 
engine,  make 
it go a  little  faster  than just 
idle.  That is, push  the accelerator 
slightly.  This  uses  less  fuel  for  the heat 
that  you  get  and it keeps the battery 
charged. 
You will  need  a  well-charged 
battery to restart  the vehicle,  and 
possibly  for  signaling  later on with your 
headlights.  Let  the heater  run for  awhile. 
Then,  shut  the  engine 
off and close  the 
window almost  all the  way  to preserve 
the  heat.  Start  the  engine again and 
repeat this  only when  you  feel  really 
uncomfortable  from  the cold. 
But do  it 
as  little  as possible.  Preserve  the fuel  as 
long  as you  can.  To  help  keep  warm, 
you  can get out  of the  vehicle  and do 
some  fairly  vigorous  exercises  every  half 
hour  or 
so until help  comes. 
3 
131 
ProCarManuals.com 
Page 138 of 248
Your Driving and the Road 
Towinga  Trailer 
NOTICE: 
Pulling  a  trailer  improperly can 
damage  your  vehicle  and result in 
costly  repairs  not covered  by your 
warranty. To  pull  a  trailer  correctly, 
follow  the advice  in this  section, 
and  see  your  Oldsmobile  dealer  for 
important  information  about 
towing  a  trailer  with your  vehicle.  Every  Bravada  is  ready  for  some  trailer 
towing.  If it was  built  with  trailering 
options,  as many  are, it’s  ready  for 
heavier  trailers.  But  trailering  is  different 
than  just  driving  your  vehicle  by itself. 
Trailering  means  changes  in handling, 
durability,  and fuel  economy.  Successful, 
safe  trailering  takes  correct  equipment, 
and  it  has  to be  used  properly. 
That’s  thereason  for  this  section.  In  it  are 
many  time-tested,  important  trailering 
tips  and  safety  rules.  Many 
of these  are 
important  for  your  safety  and  that of your 
passengers. 
So please  read  this  section 
carefully  before  you  pull  a  trailer. 
If You Do Decide To Pull A Trailer 
If  you  do,  here  are  some  important  points. 
There  are many  different  laws  having 
to  do  with trailering.  Make  sure your 
rig  will  be legal,  not only  where  you 
live  but 
also where  you’ll be driving. A 
good  source  for this  information  can 
be  state  or provincial  police. 
Consider  using  a  sway  control  if your 
trailer  will  weigh 
2,000 pounds (900 
kg)  or less. You should  always  use  a 
sway  control  if your  trailer  will  weigh 
more  than 
2,000 pounds (900 kg).  You 
can ask 
a hitch  dealer  about sway 
controls. 
Don’t  tow a  trailer  at all  during  the 
first 
500 miles (800 lun)  your  new 
vehicle  is  driven.  Your  engine,  axle  or 
other  parts could  be  damaged. 
Then, during  the first 500 miles (800 
km)  that you tow  a  trailer,  don’t drive 
over 
50 mph (80 km/h)  and don’t 
make  starts  at  full throttle.  This  helps 
your  engine  and other parts  of your 
vehicle  wear  in  at  the heavier  loads. 
Three important  considerations  have 
to 
do with weight: 
Weight of the Trailer 
How  heavy  can a  trailer  safely  be? 
It  should  never  weigh  more  than 
5,250 
pounds (2 380 kg). But  even  that can be 
too  heavy. 
It  depends  on how  you  plan  to use  your 
rig.  For  example,  speed, altitude, road 
grades,  outside temperature  and how 
much  your  vehicle  is  used  to pull  a 
trailer  are all important.  And, it can  also 
depend  on any  special  equipment  that 
you  have  on your  vehicle. 
ProCarManuals.com 
Page 139 of 248
You can  ask your dealer  for  our 
trailering information  or advice,  or you 
can  write 
us at: 
Network 
Oldsmobile 
Customer Assistance 
P.O. Box 30095 
Lansing, 
MI 48909 
In  Canada, write  to: 
General Motors  of Canada  Limited 
Customer Assistance Center  1908  Colonel  Sam Drive 
Oshawa,  Ontario 
L1H 8P7 
Weight of the Trailer  Tongue 
The  tongue  load (A) of any  trailer  is an 
important  weight to measure because  it 
affects  the total  or gross  weight  of your 
vehicle.  The 
gross vehicle  weight 
(GVW) includes  the curb  weight  of the 
vehicle,  any cargo  you  may  carry  in it, 
and  the people  who 
will be  riding  in the 
vehicle.  And 
if you will tow  a trailer, 
you  must  add the  tongue  load to  the 
GVW because  your  vehicle  will  be 
carrying  that weight,  too. See 
Loading 
Your Vehicle in the Index for more 
information  about your  vehicle’s 
maximum load  capacity. 
If  you’re  using  a  “dead-weight”  hitch, 
the  trailer  tongue 
(A) should  weigh 
10% of the  total  loaded  trailer weight 
(B). If  you have a “weight-distributing”  hitch, 
the trailer  tongue 
(A) should 
weigh  12%  of  the  total loaded trailer 
weight 
(B) . 
After  you’ve  loaded  your  trailer, weigh 
the  trailer  and  then  the tongue, 
separately,  to see  if the  weights  are 
proper.  If they aren’t,  you  may be able 
to  get  them  right simply  by moving 
some  items  around  in  the  trailer. 
Total  Weight on Your  Vehicle’s 
Tires 
Be  sure  your  vehicle’s  tires  are inflated 
to  the  limit for cold  tires.  You’ll  find 
these  numbers 
on the Certification  label 
at  the  rear edge 
of the driver’s  door or 
see 
Tire Loading in  the Index. Then  be 
sure  you don’t  go  over  the 
GVW limit 
for your  vehicle. 
C 
133 
ProCarManuals.com 
Page 140 of 248
Your Driving  and the Road 
134 
Hitches 
It’s important to have  the correct  hitch 
equipment.  Crosswinds,  large  trucks 
going  by,  and rough roads are a  few 
reasons  why  you’ll  need  the right  hitch. 
Here  are  some  rules  to follow: 
If you’ll  be pulling  a trailer  that, when 
loaded,  will  weigh  more  than 
2,000 
pounds (900 kg), be sure  to  use a 
properly  mounted,  weight-distributing 
hitch and  sway control 
of the proper 
size.  This  equipment is  very important 
for  proper  vehicle  loading  and good 
handling  when you’re  driving. 
Will  you  have to make  any  holes  in 
the  body  of your  vehicle  when you 
install  a trailer  hitch?  If you  do, then 
be  sure  to seal  the holes  later when 
you  remove  the hitch.  If you  don’t 
seal  them,  deadly  carbon  monoxide 
(CO) from  your  exhaust can  get into 
your  vehicle  (see 
Carbon Monoxide in 
the 
Index). Dirt  and water  can, too. 
. The bumpers  on your  vehicle  are not 
intended  for  hitches.  Do not  attach 
rental  hitches  or other  bumper-type 
hitches  to them.  Use  only  a frame- 
mounted hitch  that does  not  attach  to 
the  bumper.  If 
your  vehicle  has 
a deadweight  hitch 
and  a tailgate-mounted  spare tire, and 
your  trailer  has a winch  or tongue  jack, 
you  could  have  interference  between 
them. 
Safety  Chains 
You  should  always attach chains 
between  your  vehicle  and  your  trailer.  Cross  the safety  chains  under  the 
tongue  of the  trailer 
so that  the  tongue 
will  not drop  to  the road if it becomes 
separated  from the hitch. Instructions 
about  safety  chains  may be  provided  by 
the  hitch manufacturer or  by the  trailer 
manufacturer.  Follow the 
manufacturer’s  recommendation  for 
attaching  safety chains.  Always  leave 
just enough  slack 
so you can  turn  with 
your  rig.  And, never  allow  safety  chains 
to  drag  on  the  ground. 
Trailer  Brakes 
If your  trailer  weighs  more  than 1,000 
pounds (450 kg)  loaded, then it needs 
its  own  brakes 
- and they  must  be 
adequate.  Be sure  to read  and follow 
the  instructions  for the  trailer  brakes 
so 
you’ll  be  able  to install,  adjust and 
maintain  them properly.  Don’t 
tap  into  your  vehicle’s  brake 
system 
if the  trailer’s  brake  system  will 
use  more  than 
0.02 cubic  inch (0.3 cc) 
of fluid  from  your  vehicle’s  master 
cylinder.  If it does, both  braking 
systems  won’t work  well.  You  could 
even  lose  your  brakes. 
Will  the trailer  brake  parts take 3,000 
psi (20 650 kPa) of pressure?  If not, 
the  trailer  brake system  must not be 
used  with your  vehicle. 
If everything  checks out this far,  then 
make  the brake  fluid tap  at  the  port 
on the master  cylinder  that sends 
fluid  to  the  rear  brakes.  But  don’t use 
copper  tubing for this.  If 
you do, it 
will  bend  and finally  break off.  Use 
steel  brake  tubing. 
Driving  with a Trailer 
Towing  a trailer  requires  a certain 
amount  of experience.  Before  setting 
out  for the  open  road,  you’ll  want to get 
to  know  your  rig.  Acquaint yourself 
with  the feel  of handling  and braking 
with  the added  weight  of the  trailer. 
And  always  keep  in  mind  that  the 
vehicle  you  are driving  is now  a good 
ProCarManuals.com