display Oldsmobile Cutlass Supreme 1996 Owner's Manuals

LOCK (B): Before you put the key into the ignition
switch, the switch is in the
LOCK position. It’s also the
only position in which you can remove your key. This
position locks your ignition, steering wheel and
transaxle. It’s a theft-deterrent feature.
OFF (C): This position lets you turn off the engine but
still turn the steering wheel. It doesn’t lock the steering
wheel like
LOCK. Use OFF if you must have your
vehicle pushed or towed.
RUN (D): This position is where the key returns after
you start your vehicle. With the engine off, you can
use
RUN to display some of your warning and
indicator lights.
START (E): This position starts your engine.
A warning chime will sound if you open the driver’s
door when the ignition is in the
OFF, LOCK or ACC
position and the key is in the ignition.
NOTICE:
If your key seems stuck in LOCK and you can’t ,
turn it, be sure it is all the way in. If it is, then
turn the steering wheel left and right while you
turn the key hard.
But turn the key only with
your hand. Using a tool to force it could break
the key or the ignition switch.
If none of this
works, then your vehicle needs service.

Speedometer/Odometer
Your speedometer lets you see your speed in both miles
per hour (mph) and kilometers per hour
(M). Your
odometer shows how far your vehicle has been driven in
either miles (used in the United States) or in kilometers
(used in Canada).
Your Oldsmobile has a tamper-resistant odometer. If
you see silver lines between the numbers!, you'll know
someone has probably tampered with it and the numbers
may not be accurate.
You may wonder what happens if your vehicle needs a
new odometer installed. If the new one can be set to the
mileage total of the old odometer, then that will be done.
But
if it can't, then it's set at zero and a label must be
put on the driver's door to show the old mileage reading
when the new odometer was installed.
Trip Odometer
Your trip odometer tells how far you have driven since
you last reset it.
To set it to zero, press the RESET
button on the right side of the instrument cluster.
Tachometer
w RPM X 1000
The tachometer displays
the engine speed in
thousands
of revolutions
per minute (rpm).
I NOTICE:
Do not operate the engine with the tachometer in
the red area, or engine damage
may occur.
2-44

Air Conditioning with Automatic and
-Auxiliary Temperature Control
With this system, you set a temperature. You can then
either let the system adjust airflow and force to maintain
. the temperature, or you can manually adjust the flow
and force. The system works best if you keep your
windows closed while using it.
Fan Knob
The left knob selects the force of air you want when the
system
is not in AUTO. The display will show the
speed. To turn the system off,'push the
knob. ,
Driver Temperature Knob
The right knob sets the temperature for the entire system
when the light on the PASS button isn't lit. If the light is
lit, the knob sets the temperature for the driver. Turn the
knob toward red (clockwise) to raise the temperature.
Turn it toward blue (counterclockwise) to lower the
temperature.
The display will show your selection for a
few seconds, then the outside temperature will show. If
you push the knob, the system will control the fan speed
and airflow. AUTO will show on the display.
3-4

Steering Wheel Controls for Climate Audio Systems,
Control (Option)
Your Delco@ audio system has been designed to operate
easily and give years of listening pleasure. You will get
You can control certain the most enjoyment out of it
if you acquaint yourself
comfort control system with
it first. Find out what your Delco system can do
functions using the buttons and how to operate all its controls, to be sure you're
on your steering wheel. getting the most out of the advanced engineering that
went into it.
Setting the Clock
S FAN: Press the up or down arrows to increase or
decrease fan speed.
TEMP: Press the up or down arrows to increase or
decrease temperature. Press and hold
HR until
the correct hour appears. The
letter
A or P may appear on the display for AM or PM.
Then, press and hold
MN until the correct minute
appears'. The clock may be set with the ignition on
or
off.
3-9

AM-FM Stereo with Cassette Tape Player
and Automatic Tone Control
Playing the Radio
PWR:
Press the upper knob to turn the system on or off.
VOL: Turn the upper knob clockwise to increase
volume. Turn it counterclockwise to decrease volume.
RCL: Press this button briefly to recall the station
being played or to display the clock. To change what is
normally shown on the display (station or time), press
the
RCL button until you see the display you want, then
hold the
RCL button until the display flashes. If you
press the button when the ignition is off, the clock will
show for a few seconds.
Finding a Station
AM-FM: Press this button to get AM, FM1 or FM2.
The display shows your selection.
TUNE: Press this knob lightly so it extends. Turn it to
choose radio stations. Push the knob back
in when
you’re not using
it.
SEEK: Press the up or down arrow to go to the next
higher or lower station. The sound will.be muted
while seeking.
SCAN: Press this button and release it to listen to
stations for a few seconds. The radio will go to a station,
stop for a few seconds, then go on to the next station.
Press the button again to stop scanning. The sound will
be muted while scanning, and SCAN will appear on the
display. If you press SCAN for more than two seconds,
the radio will change to PSCAN mode. PSCAN will
appear on the display.
3-10

PSCAN: Press SCAN for more than two seconds, and
PSCAN will appear on the display. The radio will go to
the first preset station stored on your pushbuttons, stop
for a few seconds, then go on to the next preset station.
Press
SCAN again to stop scanning.
PUSHBUTTONS: The five numbered pushbuttons let
you return to your favorite stations. You can set up to
15 stations (five AM, five FM1 and five FM2).
1.
2.
3.
4.
5.
Press AM-FM to select the band.
Find the station you want by using TUNE or SEEK.
Press TONE to select the graph that best suits the
type of station selected.
Press and hold one of the five numbered buttons.
The sound will mute. When
it returns, release the
button. Whenever you press that numbered button,
the station you set will return and the TONE
equalization that you selected will also be
automatically selected for that button.
If you manually tune or use SEEK or SCAN to find a
frequency stored in a preset, the TONE equalization
stored for that frequency will not be recalled. Always
check the display first to make sure you have the
correct band.
Setting the Tone
TONE: This feature allows you to choose preset treble
and bass equalization settings designed for jazz, vocal,
pop, rock and classical stations.
JAZZ will appear on the
display when you first press TONE. Each time you press
it, another setting will appear on the display. Press it
again after CLASSIC appears and MANUAL will
appear. Manual tone control will return to the
TREB
and BASS knobs. Also; if you use the TREB and
BASS knobs, control will return to them and MANUAL
will appear.
BASS: Press this knob lightly so it extends. Turn the
knob to increase or decrease bass. When you use this
control, the radio’s TONE setting will switch to manual.
Push the knob back in when you’re not using it.
TREB: Press this knob lightly so it extends. Then pull
the
knob all the way out. Turn the knob to increase or
decrease treble. When you use this control, the radio’s
TONE setting will switch
to manual. Push the knob back
in when you’re not using it.
3-11

Adjusting the Speakers
BAL: Press this knob lightly so it extends. Turn the
knob
to move the sound to the left or right speakers. Use
the middle position to balance these speakers. Push the
knob back in when you’re not using it.
FADE: Press the knob lightly so it extends. Then pull
the knob all the way 0u.t. Turn it to move the sound to
the front or rear speakers. Use the middle position to
balance these speakers. Push the knob back in when
you’re not using it.
Push the knob back in when you’re not using it.
Playing a Cassette Tape
Your tape player is built to work best with tapes that are
’ 30 to 45 minutes long on each side. Tapes longer than
that
are so thin they may not work well in this player.
The longer side with
the tape visible should face to the
right.
If the ignition is on, but the radio is off, the tape
will begin playing. If you hear nothing but a garbled sound, the tape may not be in squarely. Press EJECT to
remove the tape and start over.
While the tape is playing, use the VOL, FADE, BAL,
TREB, BASS and TONE controls just as you do for the
radio. The display will show TP with a box around it
and an arrow to show which side of the tape is playing. Your
tape bias is set automatically. When a metal or
chrome tape is inserted, HI-BIAS appears on the
display.
If you want to insert a tape when the ignition is
off, first press EJECT or
RCL.
If E and a number appear on the radio display, the tape
won’t play because
of an error.
E10: The tape is tight and the player can’t turn the
tape hubs. Remove the tape. Hold the tape with the
open end down and try to turn the right hub
counterclockwise with a pencil. Turn the tape over
and repeat. If the hubs do not turn easily, your tape
may be damaged and should not be used in the
player.
Try a new tape to make sure your player is
working properly.
Ell: The tape is broken. Try a new tape.
IT any error occurs repeatedly or if an error can’t be
corrected, please contact your retailer.
If your radio
displays an error number, write
it down and provide it to
your retailer when reporting the problem.
REV (1): Press this button to reverse the tape rapidly.
Press
it again to return to playing speed. The radio will
play the last-selected station while the tape reverses. You
may select stations during
REV operation by using TUNE.
3-12

FWD (2): Pres‘s this button to advance quickly to
another part of the tape. Press the button again to return
to playing speed. The radio will play the last-selected
station while the tape advances. You may select stations
during FWD operation by using TUNE.
PROG (3): Press this button. to play the other side of
the tape.
(4): Press this button to reduce background noise.
Note that the double-D symbol will appear on the display.
Dolby@ Noise Reduction is manufactured under a
license from Dolby Laboratories Licensing Corporation.
Dolby and the double-D symbol are trademarks of
Dolby Laboratories Licensing Corporation.
SEEK: Press the up or down arrow to search for the
next or previous selection on the tape. Your tape must
have at least
three seconds of silence between each
selection for SEEK to work. After the selection has been
playing for at least eight seconds, press
the SEEK down
arrow to return to the beginning of the selection.
SCAN: Press this button to listen to each selection for a
few seconds. The tape will go to the next selection, stop
for a few seconds, then
go on to the next selection. Press
this button again to stop scanning. The sound will be
muted, SCAN will appear on the display and the tape
direction arrow will blink while scanning.
TONE: Press this button to select a TONE while
playing a cassette. The tone will be automatically set
whenever you play a cassette tape.
AM-F”: Press this button to play the radio when a tape
is in the player. The tape will stop but remain in the
player.
TAPE AUX: If you have a tape inserted and the radio is
playing, press TAPE AUX to play your tape. To return
to the radio while a tape is playing, press AM-FM. The
inactive tape will remain safely inside the radio for
future listening.
EJECT: Press this button to remove the tape. The radio
will play. EJECT may be activated with either. the
ignition or radio
off. Cassettes may be loaded with the
radio and ignition
off if this button is pressed first.
CLN: This message may appear on the display. If it
does, your cassette tape player needs to be cleaned. It
will still play tapes, but you should clean it as soon as
possible to prevent damage to your tapes and player.
See “Care ,of Your Cassette Tape Player” in the Index.
After you clean the player, press and hold EJECT for
five seconds to reset the CLN indicator. The radio will
display
--- to show the indicator was reset.
3-13

AM-FM Stereo with Compact Disc Player
with Automatic Tone Control (Option)
Playing the Radio
PWR:
Press this button to turn the system on or off.
VOL: Turn this knob clockwise to increase volume.
Turn it counterclockwise to decrease volume.
RCL: Press this button briefly to recall the station
being played
or to display the clock. To .change what is
normally shown on the display (station or time), press
the button until you see the display you want, then hold
the button until the display flashes.
If you press the
buttan
when the ignition is off, the clock will show for a
few seconds.
Finding a Station
AM-FM:
Press this button to get AM, FM1 or FM2.
The display shows your selection.
TUNE: Press this knob lightly so it extends. Turn it to
choose radio stations. Push the knob back in when
you’re not using it.
SEEK:‘Press the up or down arrow to go to the next
higher or lower station. The sound will be muted
while seeking.
SCAN: Press this button and release it to listen to
stations for a few seconds. The radio will go to a station,
stop for a few seconds, then go on to the next station.
Press the button again to stop scanning. The sound will
be muted while scanning,
and SCAN will appear on the
display.
If you press SCAN for more than two seconds,
the radio will change to PSCAN mode. PSCAN will
appear on the display.
3-14

PSCAN: Press SCAN for more than two seconds, and
PSCAN will appear on the display. The radio will go to
the first preset station stored on your pushbuttons, stop
for a few seconds, then go on to the next preset station.
Press SCAN again to stop scanning.
PUSHBUTTONS: The five numbered pushbuttons let
you return to your favorite stations. You can set up to
15 stations (five AM,
five FM1 and five FM2).
1.
2.
3.
4.
5.
Press AM-FM to select the band.
Find the station you want by using.TUNE or SEEK.
Press TONE to select the graph that best suits the
type of station selected.
Press and hold one of the five numbered buttons.
The sound will mute. When it returns, release the
button. Whenever you press that numbered button,
the station you set will return and the TONE
equalization that
you selected will also be
automatically selected for that button.
If you manually tune or use SEEK or SCAN to find a
frequency stored in a preset, the TONE equalization
stored for that frequency will not be recalled. Always
check the display first to make sure you have the
correct band.
Setting the Tone
TONE:
This feature allows you to choose preset treble,
and bass equalization settings designed for jazz, vocal,
pop, rock and classical stations.
JAZZ will appear on the
display when you first press TONE. Each time you press
it, another setting will appear on the display. Press it
again after CLASSIC appears and MANUAL will
appear. Tone control will return to the TREB and BASS
knobs. Also, if you use the TREB and BASS knobs,
control will return to them and MANUAL will, appear.
BASS: Press this knob lightly so it extends. Turn the
knob to increase or decrease bass. The ‘middle position is
a detent. When you use this control, the radio’s TONE
setting will switch to manual.
TREB: Press this knob lightly so it extends. Then pull
the knob all the way out. Turn the knob to increase or
decrease treble. The middle position is a detent. When
you use this control, the radio’s TONE setting will
switch to manual.
Push the knobs back in when you’re not using them.
3-15