light OLDSMOBILE INTRIGUE 1998 Repair Manual
Page 243 of 340
How to  Reset the CHANGE OIL Light 
After changing the engine  oil,  the system must be  reset 
1. 
2. 
3. 
With  the ignition key in ON but the engine  off, fully 
push and  release the accelerator pedal  slowly  three 
times  within  five  seconds. 
If the  CHANGE  OIL  light  flashes,  the system 
is  resetting. 
Turn the  key to OFF, then start the vehicle.  If the 
CHANGE OIL light comes back  on,  the  engine  oil 
life  monitor has not reset. Repeat the  procedure. 
What  to Do with  Used  Oil 
Did you know that used engine oil contains  certain 
elements  that  may be unhealthy  for your skin and  could 
even cause  cancer?  Don’t let used oil stay on your  skin 
for  very  long. Clean your skin and nails  with  soap and 
water,  or  a good hand cleaner.  Wash or properly throw 
away  clothing  or  rags  containing  used engine  oil.  (See 
the manufacturer’s warnings  about  the  use and disposal 
of  oil  products.) 
Used  oil  can  be  a  real threat  to  the environment. 
If you 
change your own  oil,  be  sure  to drain all free-flowing  oil 
from  the  filter  before  disposal.  Don’t ever  dispose  of oil 
by  putting 
it in the  trash, pouring  it on  the  ground,  into 
sewers,  or  into  streams  or  bodies  of water.  Instead, 
recycle  it  by taking  it  to  a  place  that collects  used oil. 
If 
you have  a problem properly  disposing of your used  oil, 
ask  your retailer, 
a service  station or  a  local  recycling 
center  for  help. 
6-15 
ProCarManuals.com 
Page 249 of 340
Engine Coolant 
The  cooling s stem in your  vehcle  is filled  with 
DEX-COOL 
J engine  coolant.  This  coolant  is  designed 
to  remain  in your  vehicle  for 
5 years  or 150,000 miles 
(240 
000 km) whichever  occurs  first,  if you add only 
DEX-COOL’  extended  life  coolant. 
The  following  explains  your cooling  system and how  to 
add  coolant  when it  is low.  If you  have  a  problem with 
engine  overheating 
or if  you need  to add  coolant  to  your 
radiator,  see “Engine Overheating” in  the Index. 
A 50150 mixture  of water and  DEX-COOL@ 
coolant  will: 
0 Give  freezing  protection  down  to -34°F  (-37°C). 
Give boiling  protection up to 265 “F (129°C). 
0 Protect  against  rust  and corrosion. 
0 Help  keep  the  proper  engine  temperature. 
Let  the  warning  lights and gages work  as 
they  should. 
NOTICE: 
When  adding  coolant,  it is  important  that  you 
use  only 
DEX-COOL@ (silicate-free)  coolant. 
If coolant  other  than  DEX-COOL  is added  to 
the  system,  premature  engine, heater core 
or 
radiator  corrosion  may result.  In addition,  the 
engine  coolant  will require  change sooner 
-- at 
30,000 miles (50 000 km) or 24 months, 
whichever  occurs first.  Damage  caused  by  the 
use  of coolant  other  than  DEX-COOL@  is  not 
covered  by  your new  vehicle  warranty. 
6-21 
ProCarManuals.com 
Page 251 of 340
Checking  Coolant 
The coolant recovery tank is located in the engine 
compartment behind the headlamp on 
the driver’s  side. 
When your  engine  is  cold,  the  coolant  level should  be at 
the  COLD  mark or  a little higher. When your  engine is 
warm, the  level should be  up to 
HOT mark. To check 
the  coolant  level,  remove  the cap on the  coolant 
recovery tank and verify that the coolant  level is up  to 
the  COLD  fill  level on the hose  attached  to 
the cap,  or  a 
little  higher. 
&I If this low  coolant 
warning  light comes  on, 
it  means you’re low on 
engine  coolant. 
Adding Coolant 
If  you need more  coolant, add the proper DEX-COOL@ 
coolant  mixture 
at the coolant recovery tank, but  be 
careful not  to  spill it. 
If  the  coolant  recovery tank  is completely empty, add 
coolant  to 
the radiator.  (See “Engine Overheating” in 
the Index.) 
6-23 
ProCarManuals.com 
Page 255 of 340
Brakes 
Brake Fluid 
goes  back  up. The other  reason  is  that  fluid is leaking  out 
of the  brake  system. If it is,  you  should  have  your  brake 
system  fixed,  since a leak  means  that  sooner  or later  your 
brakes  won’t  work 
well, or  won’t  work  at  all. 
So, it isn’t a good idea  to  “top off’ your brake  fluid. 
Adding brake  fluid won’t  correct 
a leak. If you add fluid 
when your  linings  are worn, then you’ll have  too much 
fluid  when  you  get new  brake linings.  You should add 
(or remove) brake  fluid, 
as necessary, only when work is 
done on the brake hydraulic system. 
Your  brake  master  cylinder  reservoir 
is here. It is filled 
with 
DOT-3 brake  fluid. 
There  are only  two reasons  why  the  brake  fluid  level 
in the 
reservoir  might  go down.  The first is that  the  brake  fluid 
goes  down  to 
an acceptable  level  during  normal  brake 
lining  wear. 
When new  linings  are put in, the  fluid  level 
If’ you  have  too  much  brake  fluid,  it  can  spa on  the 
engine.  The  fluid 
will burn if‘ the  engine is hot 
enough.  You  or  others  could  be  burned,  and 
your 
vehicle  could  be  damaged.  Add  brake  fluid  only 
when  work 
is done  on  the  brake  hydraulic  system. 
When  your brake fluid  falls  to  a low level, your  brake 
warning light  will come  on.  See  “Brake System Warning 
Light” 
in the Index. 
6-27 
ProCarManuals.com 
Page 257 of 340
Brake  Wear 
Your vehicle  has four-wheel  disc  brakes. 
Disc  brake  pads  have  built-in  wear  indicators  that  make  a 
high-pitched  warning  sound  when  the  brake  pads  are  worn  and  new  pads  are  needed.  The  sound  may  come  and 
go or 
be heard all the time  your  vehicle  is  moving  (except  when 
you  are  pushing  on  the  brake 
pedal firmly). 
- m-- 
A CAUTION: 
I 
The  brake  wear  warning  sound  means  that  soon 
your  brakes  won’t  work  well.  That  could  lead  to 
an  accident.  When  you  hear  the  brake  wear 
warning  sound,  have  your  vehicle  serviced. 
NOTICE: 
Continuing  to  drive  with  worn-out  brake  pads 
could  result  in  costly  brake  repair. 
Some  driving  conditions  or  climates may cause  a  brake 
squeal  when the brakes  are  first applied  or lightly 
applied.  This  does not  mean  something  is wrong  with 
your  brakes. 
Properly torqued wheel  nuts are necessary  to help 
prevent brake  pulsation. When tires are rotated,  inspect 
brake pads  for wear and evenly torque  wheel nuts in  the 
proper  sequence  to 
GM specifications. 
Brake  linings  should always  be replaced  as complete 
axle  sets. 
See  “Brake  System  Inspection”  in  Section 
7 of this manual 
under  Part 
C “Periodic  Maintenance  Inspections.” 
Brake  Pedal  Travel 
See  your  retailer if the  brake  pedal does  not return  to 
normal  height, or if there  is 
a rapid  increase in pedal 
travel. This could  be a sign  of brake  trouble. 
Brake  Adjustment 
Every time  you apply  the  brakes,  with or without the 
vehicle moving,  your brakes adjust  for wear. 
6-29 
ProCarManuals.com 
Page 271 of 340
Mixing  tires  could  cause you to  lose  control  while 
driving.  If  you  mix  tires  of different  sizes or  types 
(radial  and  bias-belted  tires),  the  vehicle  may  not 
handle  properly,  and  you could  have 
a crash. 
Using  tires of different  sizes may  also  cause 
damage  to  your  vehicle. Be sure  to  use  the  same 
size  and  type  tires  on 
all wheels. 
It’s  all  right  to  drive  with  your  compact  spare, 
though.  It was  developed  for use  on  your  vehicle. 
I A CAUTION: 
If you use  bias-ply  tires  on  your  vehicle, the 
wheel  rim  flanges  could  develop  cracks  after 
many  miles  of driving. 
A tire  and/or  wheel could 
fail  suddenly,  causing 
a crash.  Use only  radial-ply 
tires  with  the  wheels  on  your  vehicle. 
Uniform Tire Quality  Grading 
The  following  information relates  to the system 
developed  by the United  States National Highway 
Traffic Safety  Administration,  which grades tires 
by 
treadwear, traction and temperature performance.  (This 
applies  only to vehicles 
sold in the United  States.)  The 
grades  are  molded on the  sidewalls of most  passenger 
car  tires. The Uniform Tire Quality Grading system does 
not  apply  to deep  tread,  winter-type  snow tires, 
space-saver  or temporary  use  spare tires, tires  with 
nominal rim  diameters 
of 10 to 12 inches (25 to 30 cm), 
or 
to some limited-production  tires. 
While the tires  available on General Motors passenger 
cars and  light trucks  may  vary  with  respect 
to these 
grades,  they must also conform to Federal safety 
requirements  and  additional General Motors Tire 
Performance  Criteria  (TPC)  standards. 
6-43 
ProCarManuals.com 
Page 282 of 340
Appearance  Care  Materials  Chart 
PART NUMBER I SIZE DESCRIPTION USAGE I 
994954 
Exterior polishing cloth 
Polishing  Cloth - Wax 
Treated 
23  in.  x 25 in. 
1050172  Removes  tar,  road  oil  and  asphalt 
Tar  and  Road  Oil Remover 
16 
oz. (0.473 L) 
1050173 
Cleans vinyl tops, upholstery  and convertible  tops 
Vinyl  Cleaner 
32 
oz. (0.946 L) 1050214  Removes  soil  and  black  marks 
from whitewalls 
White  Sidewall Tire Cleaner 
16 
oz. (0.473 L) 1050174  Use  on  chrome,  stainless  steel,  nickel,  copper  and  brass 
Chrome  Cleaner and Polish 
16 
oz. (0.473 L) 
1050427 
Cleans and lightly  waxes 
Wash  Wax  Concentrate 
16 
oz. (0.473 L) 1052870  Removes 
dirt, grime, smoke and fingerprints 
Glass Cleaner 
23 
oz. (0.680 L) 
-- 
1052918** 
Armor  All TM Protectant 
8 oz. (0.237 L) Protects  leather,  wood,  acrylics, Plexiglas TM, plastic, 
rubber  and  vinyl 
1052925 
I 16 oz. (0.473 L) I Multi-Purpose Interior  Cleans carpets, seats, interior trim, door panels 
I Cleaner  and floor mats I 
1052929  16 oz. (0.473 L) 
1052930 8 oz. (0.237 L) 
12377964 
16 oz. (0.473 L) 
Wheel Cleaner  Spray  on  and  rinse  with  water 
Capture  Dry Spot Remover  Attracts,  absorbs  and removes soils 
Armor 
All TM Cleaner  Cleans  and shines a  variety of surface  types 
Synthetic Chamois  Shines  vehicle without scratching 
_____~ 
Silicone  Tire Shine  Spray  on tire shine 
Finish Enhancer  Removes dust, fingerprints  and surface contaminants 
12377966  16 
oz. (0.473 L) Cleaner Wax  Removes  light  scratches  and  oxidation  and  protects  finish 
12377984  16 
02. (0.473 L) Surface Cleaner  Removes 
contaminants, blemishes  and  swirl  marks 
See  your  General Motors Parts Department 
for these products. ** Not  recommended for use  on  instrument  panel  vinyl. 
See “Fluids  and Lubricants”  in the Index. 
6-54 
ProCarManuals.com 
Page 286 of 340
I Fuse Description 
Fuse 
IGN 0: I/P Cluster, Powertrain Control 
1 CLUSTER  PCM, Module, Body Control 
I &BCM I 
1 LOW  BLOWER  HVAC 
Control Assembly, 
Blower Motor 
~ HVAC 
CRUISE 
ABS 
BTSI  Air Temperature 
Valve Motor, 
HVAC  Control Assembly, 
Solenoid Box 
Cruise Control Module 
Electronic Brake Control Module  (EBCM)  ABS Relay,  TCS 
Disable Switch 
Brake-Transaxle Shift Interlock 
TURN SIGNALS,  Turn Signals, Cornering Lamps  CORN  LPS 
AIR  BAG 
CLUSTER 
DRL  Air 
Bag System 
Instrument Panel Cluster 
Daytime Running Lamps  PCM,  BCM, 
U/H  RELAY 
RADIO,  WAC, 
RFA  CLUSTER 
DATA  LINK 
ABS,  BCM 
CIGAR  LTR, 
AUX  POWER, 
POWER  DROP INADV 
POWER BUS 
Description 
Powertrain Control Module, Body 
Control Module, Underhood 
IgnitiodRelay 
Radio,  HVAC  Control Assembly, 
Instrument Panel Cluster, Remote 
Keyless Entry Module, Data 
Link 
Connector,  Bose Amplifier 
ABS1 -- Electronic Brake 
Control Module (EBCM), Body 
Control Module 
Auxiliary  Power, Cigarette 
Lighter, Power  Drop 
Vanity  Mirrors, 
I/P Courtesy 
Lamps, 
I/P Compartment Lamps, 
Trunk Courtesy Lamp, Header  Courtesy and Reading Lamps, 
US 
Lighted Rearview Mirror 
CD  CHANGER  Cartridge Disk Changer 
HIGH  BLOWER  High Blower Relay 
HAZARD  Hazard Switch 
i 6-58 
ProCarManuals.com 
Page 289 of 340
Fuse  Description 
7 Interior Lamps, Retained Accessory Power, 
ABS, Keyless Entry,  CEL  TEL, Data Link, 
HVAC  Head, Cluster, Radio, AUX Power, 
Cigarette  Lighter 
8 Ignition  Switch,  Wipers,  Radio,  Steering 
Wheel  Controls,  Body Control  Module, 
AUX  Power,  Power Windows,  Sunroof, 
HVAC  Controls,  DRL, Rear Defog Relay 
Relay  Description 
9 Cooling Fan 2 
10 Cooling Fan 3 
11 Starter  Solenoid 
12 Cooling Fan 1 
13 Ignition Main 
14 Not Used 
15 A/C Clutch 
Relay 
16 
17 
18 
19 
Fuse 
20 
21 
22 
23 
24 
25 
26 
27 
28 
29 
Description 
Horn 
Fog Lamps  Fuel  Pump 
Fuel Pump 
Description 
Air Pump 
Generator 
ECM  A/C Compressor Clutch 
Not Used 
Electronic  Ignition 
Transaxle 
Horn  Fuel  Injector 
Oxygen Sensor 
ProCarManuals.com 
Page 297 of 340
I Maintenance  Schedule I 
The  services shown in this  schedule  up to  100,000  miles 
(I 66 000 km) should be performed  after 100,000 miles 
(1 
66 000 km) at  the same  intervals.  The  services  shown 
at 
150,000 miles (240 000 km) should  be performed  at 
the  same  interval  after 
150,000 miles (240 000 km). 
See  “Owner Checks and  Services” and “Periodic 
Maintenance  Inspections”  following. 
Footnotes 
? The U.S. Environmental  Protection Agency  or the 
California Air Resources Board has determined that  the 
failure  to perform this maintenance  item  will not nullify 
the  emission  warranty or  limit recall liability prior  to 
the completion of the vehicle‘s useful life. We,  however, 
urge that all recommended  maintenance  services 
be  performed  at the indicated  intervals and the 
maintenance be  recorded. 
* Your vehicle has an Engine Oil  Life Monitor.  This 
monitor will show 
you when to change the  engine oil 
and  filter 
-- usually between 3,000 miles (5 000 km) 
and 
7,500 miles (12 500 km)  since  your last oil change. 
Under  severe  conditions,  the indicator  may come on 
before 
3,000 miles (5 000 km). Never  drive your vehicle 
more than 
7,500 miles (12 500 km) or 12  months 
without an oil and  filter  change. 
The  system won’t  detect dust in the oil. 
So if  you 
drive 
in a dusty area,  be  sure to change your oil and 
filter  every 
3,000 miles (5 000 km)  or  sooner  if the 
CHANGE 
OIL light  comes  on. Remember to reset the 
Oil  Life  Monitor  when the oil has  been changed. 
For 
more  information,  see  “Engine Oil” in the Index. 
+ A good  time  to check your brakes is during tire 
rotation.  See “Brake System Inspection’’  unde.r “Periodic 
Maintenance  Inspections”  in Part  C 
of this schedule. 
7-5 
ProCarManuals.com