Oldsmobile Intrigue 2002 Owner's Manuals

2-37 Flash-to-Pass Feature
With the lever in the low-beam position, pull the
lever toward you momentarily to switch to high beams
(to signal you are going to pass). If you have the
headlamps on, they will return to low beams when
you release the lever.
Windshield Wipers
Use this lever located on the right side of the steering
wheel to operate the windshield wipers.
OFF: Move the lever to OFF to turn off the
windshield wipers.INT (Intermittent): Move the lever to INT to choose a
delayed wiping cycle. Turn the INT ADJ band down for
a longer delay or up for a shorter delay. The further the
INT ADJ band is turned upward, the shorter the delay
will be and the further the INT ADJ band is turned
downward, the longer the delay will be. The wiper speed
can only be adjusted when the lever is in the INT
position. Use this position for light rain or snow.
LO (Low Speed): Move the lever up to the first setting
past INT, for steady wiping at low speed.
HI (High Speed): Move the lever up to the second
setting past INT, for steady wiping at high speed.
MIST: Move the lever all the way down to MIST for a
single wiping cycle. Hold it there until the windshield
wipers start; then let go. The windshield wipers will stop
after one wipe. If you want more wipes, hold the band
on MIST longer.
Heavy snow or ice can overload the wipers. If this
occurs, a circuit breaker will stop the wipers until the
motor cools. So, be sure to clear any ice and snow from
the windshield wiper blades before using them. If the
wiper blades are frozen to the windshield, carefully
loosen them, or warm the windshield before turning the
wipers on. If your blades do become worn or damaged,
get new blades or blade inserts.

2-38 Windshield Washer
At the end of the lever on right side of the steering
wheel, is a wiper symbol.
To spray washer fluid on the windshield, push the button
on the end of the lever. The wipers will run for several
cycles and then either stop or return to the preset speed.
CAUTION:
In freezing weather, don't use your washer until
the windshield is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
The LOW WASHER
FLUID light, located on the
instrument panel will come
on when your vehicle is low
on washer fluid.
If you see this light while driving, your vehicle's washer
fluid is low. You should refill the windshield washer
fluid reservoir as soon as possible so that you'll have
washer fluid when you need it.

2-39 Cruise Control
With cruise control, you can maintain a speed of about
25 mph (40 km/h) or more without keeping your foot
on the accelerator. This can really help on long trips.
Cruise control does not work at speeds below about
25 mph (40 km/h).
When you apply your brakes, the cruise control
shuts off.
CAUTION:

Cruise control can be dangerous where you
can't drive safely at a steady speed. So,
don't use your cruise control on winding
roads or in heavy traffic.

Cruise control can be dangerous on
slippery roads. On such roads, fast changes
in tire traction can cause needless wheel
spinning, and you could lose control. Don't
use cruise control on slippery roads.
If your vehicle is in cruise control when the optional
traction control system begins to limit wheel spin,
the cruise control will automatically disengage. See
ªTraction Control Systemº in the Index. When road
conditions allow you to safely use it again, you may turn
the cruise control back on.

2-40
Setting Cruise Control
CAUTION:
If you leave your cruise control switch on when
you're not using cruise, you might hit a button
and go into cruise when you don't want to. You
could be startled and even lose control. Keep the
cruise control switch off until you want to use
cruise control.
1. Press the CRUISE
button located on the
right side of the
instrument panel to turn
it on. A light in the
button will indicate that
the system is on.2. Get up to the speed you want.
3. Press the COAST SET
button located on your
steering wheel and
release it.
4. Take your foot off the accelerator.
The CRUISE light on the instrument panel cluster will
come on after the cruise control has been set to the
desired speed. It will go off when you do the following:

Step lightly on the brake pedal,

press the CLEAR button located on the steering
wheel or

press the CRUISE button located on the
instrument panel.

2-41
Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you either apply the brake or press the clear
button located on the steering column. This, of course
shuts off the cruise control. But you don't need to reset
it because the system remembers the last set speed.
Once you're going about 25 mph (40 km/h) or more,
press the RES ACCEL (Resume Accelerate) button
located on your steering wheel. You'll go right back up
to your chosen speed and stay there.
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed:

Use the accelerator pedal to get to the higher speed.
Press the COAST SET button located on the steering
wheel, then release the button and the accelerator
pedal. You'll now cruise at the higher speed.

Press the RES ACCEL button located on the steering
wheel. Hold it there until you get up to the speed you
want and then release the button. To increase your
speed in very small amounts, press the RES ACCEL
button briefly and then release it. Each time you do
this, your vehicle will go 1 mph (1.6 km/h) faster.
The accelerate feature will only work after you set the
cruise control speed by pressing the COAST SET button
located on the steering wheel.Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:

Press the COAST SET button located on the steering
wheel until you reach the lower speed you want, then
release it.

To slow down in very small amounts, press the
COAST SET button located on the steering wheel
briefly and then release it. Each time you do this,
you'll go 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise speed you set earlier.

2-42
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Of course, applying the brake
takes you out of cruise control. Many drivers find this to
be too much trouble and don't use cruise control on
steep hills.
Ending Cruise Control
There are three ways to cancel the cruise control:

Step lightly on the brake pedal,

press CLEAR located on the steering wheel or

press the CRUISE button located on the
instrument panel.
Erasing Cruise Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.Exterior Lamps
The lever on the left side of the steering column
operates the exterior lamps.
: Turn the outside part of the lever with this symbol
on it to operate the lamps.
The exterior lamp switch has three positions.
OFF:
Turning the switch to this position turns off all
lamps, except the Daytime Running Lamps, (DRL).

2-43
(Parking Lamps): Turning the switch to
this position turns on the parking lamps together with
the following:

Sidemarker Lamps

Taillamps

License Plate Lamp

Instrument Panel Lights
(Headlamps): Turning the switch to this position
turns on the headlamps, together with the previously
listed lamps and lights.
Turn the control to OFF to turn off the lamps.
A warning chime will sound, indicating the lamps are on
when the driver's door is open and the ignition switch is
in the OFF or ACCESSORY position.
Daytime Running Lamps / Automatic
Headlamp Control
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset. Fully
functional daytime running lamps are required on all
vehicles first sold in Canada.
A light sensor on top of the instrument panel makes the
DRL work, so be sure it isn't covered.
The DRL system will make your front turn signal lamps
come on when the following conditions are met:

The ignition is on,

the exterior lamp control is not in the headlamp
position position and

the parking brake is released.
When the DRL are on, only your front turn signal lamps
will be on. The headlamps, taillamps, sidemarker and
other lamps won't be on. The instrument panel won't be
lit up either.

2-44
When it's dark enough outside, your front turn signal
lamps will turn off and your headlamps and parking
lamps will turn on.
When it's bright enough outside, your headlamps will go
off and your front turn signal lamps will come on.
To idle your vehicle with the DRL or automatic
headlamps off, set the parking brake while the ignition is
in OFF. Then start your vehicle. The DRL, headlamps
and parking lamps will stay off until you release the
parking brake.
To turn off the automatic headlamp feature when it's
dark outside, move the exterior lamp control to the
parking lamp position. Your parking lamps will remain
illuminated and your headlamps will turn off. The fog
lamps (if equipped) will also be lit if they were on when
you changed to the parking lamp position.
As with any vehicle, you should turn on the regular
headlamp system when you need it.Fog Lamps (If Equipped)
The fog lamps are located
on the left side of the
instrument panel.
The parking lamps must be on or your fog lamps will
not illuminate.
To turn the fog lamps on, press the top of the fog lamp
switch. Press the bottom of the switch to turn the fog
lamps off. A light will glow in the switch to let you
know that they are on.
The fog lamps will go off whenever you change to
high
-beam headlamps. When you return to low beams,
the fog lamps will come on again.

2-45
Interior Lamps
Instrument Panel Brightness Control
This feature controls the brightness of the instrument
panel lights.
The thumbwheel for this
feature is located on the left
side of the instrument panel.
Turn the thumbwheel upward to increase the brightness
of the instrument panel lights or downward to decrease
the brightness.Parade Mode
The instrument panel brightness control has an added
feature called parade mode to assist you in seeing
certain instrument panel controls if your headlamps
are on in the daylight.
Without turning the courtesy lamps on, turn the
instrument panel brightness thumbwheel all the way to
the top. The radio, season/trip odometer, gearshift
selection indicator on the instrument panel cluster and
the heating and air conditioning controls will come on at
their maximum brightness. This will occur only when
the parking lamps or headlamps are on.
Courtesy Lamps
When any door is opened, several lamps come on. These
lamps are courtesy lamps. They make it easy for you to
enter and leave your vehicle. You can also turn these
lamps on by turning the instrument panel brightness
thumbwheel all the way up or by turning on each
individual lamp.

2-46 Illuminated Entry
Your courtesy lamps will come on and stay on for a set
time whenever you press UNLOCK on the remote
keyless entry transmitter (if equipped).
If you open a door, the lamps will stay on while it's open
then turn off automatically about 25 seconds after you
close it. If you press UNLOCK and don't open a door,
the lamps will turn off after about 40 seconds.
Illuminated entry includes a feature called theater
dimming. With theater dimming, the lamps don't just
turn off at the end of the delay time. Instead, they slowly
dim after the delay time until they go out. The delay
time is cancelled if you turn the ignition key to ON
so that the lamps will dim out right away. When the
ignition is on, illuminated entry is inactive, which
means the courtesy lamps won't come on unless
a door is opened.
Illumination on Door Handle Activation
Illumination on door handle activation is a standard
feature intended to provide enhanced security and
convenience by allowing the driver to activate the
vehicle interior illumination without unlocking or
opening any vehicle door.The ignition must be off and the doors locked for the
illumination on door handle activation to work. The
illumination on door handle activation feature can
function in two ways.
If the driver pulls and releases any front door handle
within one second, the interior lamps will illuminate
until one of the following occurs:

The ignition is turned to ON,

the power door locks are activated or

an illumination period of 25 seconds has elapsed.
Or, if the driver pulls and holds any front door handle
for more than one second, the interior lamps will
illuminate until one of the following occurs:

The ignition is turned to ON,

the door handle is released or

an illumination period of 50 seconds has elapsed.
If during the illumination period a door is opened,
the timed illumination period will be cancelled, though
the interior lamps will remain on because a vehicle door
is open.