key battery OPEL AGILA 2009 Owners Manual

Page 17 of 153

2-2Keys, doors and windows
Fault
If the central locking system cannot
be operated with the remote control,
this may be due to the following
reasons:
„The remote control is out of range.
„The battery voltage of the remote
control is too low. Change the
battery in the remote control unit.
„Interference from higher power
radio waves from other sources.
Lock or unlock the doors manually
using the key or central locking switch
3 2-3, 2-4.
Seek the assistance of a workshop to
rectify the cause of the fault.
Changing battery in remote
control unit
Replace the battery (CR 1620 or
equivalent) in accordance with the
chapter “Service and maintenance”
311-2 or when the range of the
remote control starts to become
reduced.
Remove screw on key cover and
remove the transmitter.
Prise apart both halves of transmitter
with a suitable screwdriver.Replace battery, ensuring the new
battery is installed correctly with
positive (+) side facing the positive
(+) terminal.
Reattach both halves of transmitter
and reinstall in holder, ensuring it
engages correctly.
Replace cover and tighten screw.
Battery disposal
Batteries are not to be treated as
household waste. They should be
disposed of at a designated collection
point for recycling.

Page 59 of 153

5-9Instruments and controls
X Driver’s seat belt
Will illuminate in red when ignition is
switched on if driver’s seat belt is not
engaged.
If vehicle speed exceeds 15 km/h
(9 mph) and driver’s seat belt is not
engaged, the control indicator will
flash for approx. 90 seconds along
with a warning chime and then
illuminate until driver’s seat belt is
fastened correctly.
Seat belts 3 3-5.
v Airbag systems, belt
tensioners
Will flash in red several times when
the ignition is switched on, then
extinguish.
If it does not flash when the ignition is
switched on, stays lit, illuminates or
flashes whilst driving, there is a fault
with the airbag systems or with the
belt tensioners. The systems might
not therefore be triggered in the event
of an accident. Seek the assistance
of a workshop immediately.
Belt tensioners 3 3-6, airbags 3 3-13.
p Charging system
Will illuminate in red when ignition is
switched on. Extinguishes after
engine is started.
If it stays lit after the ignition is
switched on or illuminates during
driving: stop vehicle and switch off
engine. The battery is not being
charged and the engine cooling may
be interrupted. The brake servo unit
may cease to be effective. Interrupt
your journey immediately.
Remove ignition key and check drive
belt condition and tensioning before
seeking the assistance of a
workshop.
s Service transmission 3
Will illuminate briefly in yellow when
the ignition is switched on.
If it flashes, there is a fault in the
automatic transmission. Seek the
assistance of a workshop
immediately.
Automatic transmission 39-3.
R Brake system
Will illuminate in red when ignition is
switched on. Extinguishes after
engine is started.
Illuminates when engine is running if
parking brake is applied and/or fluid
level for brake hydraulics is too low.
Further information 3 9-9,
brake fluid level 3 10-6.
u Anti-lock Brake System
(ABS)
Will illuminate briefly in yellow when
ignition is switched on.
At the same time, the system
performs a self-check. When the
control indicator extinguishes, the
system is ready for operation.
Caution
If it illuminates when the parking
brake is not applied: stop vehicle;
interrupt your journey immediately.
Seek the assistance of a workshop.

Page 61 of 153

5-11Instruments and controls
If it stays lit or illuminates during
driving, there is a fault with ESP®.
The vehicle’s brake system remains
operational without ESP
® regulation.
Seek the assistance of a workshop to
have the cause of the fault remedied.
Further information 3 9-10.
W Engine coolant
temperature
Will illuminate briefly in red when
ignition is switched on.
If it illuminates or flashes when the
engine is running: stop vehicle and
switch off engine. Coolant
temperature is too high; danger of
engine damage. Check coolant level.
Further information 3 10-4.
N Preheating for diesel
engines 3
Will illuminate during engine
preheating.
Preheating system switches on only if
outside temperature is low.
If it illuminates during driving or if the
engine cannot be started, seek the
assistance of a workshop as soon as
possible.
Starting the engine 3 9-2.
Z Exhaust emissions
Will illuminate in yellow when ignition
is switched on. Extinguishes after
engine is started.
If it illuminates when the engine is
running: fault in emission control
system. The permitted emission
limits may be exceeded. Fuel
economy and vehicle driveability may
be impaired. Seek the assistance of a
workshop immediately.Diesel engines: The engine stops and
control indicator Z illuminates if the
fuel level is too low. If the tank has
been run dry, bleed the fuel system 3
10-7.
Vehicles with electric throttle body
system 3: If the battery has been
disconnected, the system must be
recalibrated upon reconnection of the
battery. Hold ignition key in ON
position for 5 seconds without
running the engine. Control indicator
Z remains illuminated after the
engine is started if the procedure is
not successful.
I Engine oil pressure
Will illuminate in red when ignition is
switched on. Extinguishes after
engine is started.
If it illuminates during driving; engine
oil pressure may be dangerously low,
interrupting engine lubrication and
resulting in damage to the engine
and/or locking of the drive wheels:
„Move out of the flow of traffic as
quickly as possible without
impeding other vehicles,
9 Warning
Allow engine to cool down before
removing coolant filler cap.

Page 70 of 153

6-4 Lighting
Interior lighting
Courtesy lamps
Move switch position:In the DOOR position, front interior
lamps and the luggage compartment
lamp function as courtesy lamps and
illuminate when the doors or tailgate
are opened. If doors or tailgate
remain opened, lamps remain
illuminated for approx. 15 minutes.
Once all doors and the tailgate are
closed, the courtesy lamps dim
gradually after approx. 15 seconds.
Lamps dim immediately when key is
inserted in ignition.
When key is removed from ignition,
courtesy lamps illuminate for approx.
15 seconds before dimming
gradually.
Depending on equipment version,
opening certain doors may not cause
courtesy lamps to illuminate, even
while the switch is in the DOOR
position. Doors which cause courtesy
lamps to illuminate are identified by a
switch in the door opening 3.
The tailgate always causes courtesy
lamps to illuminate when the interior
lamp switch is in the DOOR position.
Luggage compartment lamp
Illuminates when a door or the
tailgate is opened. OFF = Interior lamps remain
off.
DOOR = Interior lamps
illuminate when a
door or the tailgate is
opened.
ON = Interior lamps remain
on.
Caution
To prevent the battery from
becoming discharged, do not leave
the interior lamp switch in the ON
position when leaving the vehicle.

Page 92 of 153

9-5 Driving and operating
Stopping the vehicle
Engage parking brake and move
selector lever to position P. It will not
be possible to turn the ignition key to
the LOCK position unless the selector
lever is in positionP.
Rocking the vehicle
If it becomes necessary to rock the
vehicle to free it from water, ice, sand,
mud, snow or a dip, observe the
following:
Move the selector lever between R
and a forward gear in a repeat pattern
while applying light pressure to the
accelerator pedal when the vehicle is
in gear.
Do not spin the wheels or race the
engine and avoid sudden
acceleration.
Manoeuvring the vehicle
To manoeuvre the vehicle back and
forth during attempts to park or in
garage entrances, the creeping
movement can be utilized by
releasing the foot brake.
Never actuate the accelerator and
brake pedals simultaneously.
Fault
If there is a problem with the
automatic transmission, control
indicator
s flashes. The transmission
no longer shifts automatically.
Seek the assistance of a workshop to
rectify the cause of the fault.
Interruption of power supply
If the vehicle battery is flat, the
selector lever cannot be moved out of
position P.
Start the vehicle using jump leads 3
10-26.

Page 93 of 153

9-6Driving and operating
If the battery is not the cause of the
fault, release selector lever as
follows:This procedure is for emergency use
only. If repeated use of this procedure
is necessary, or the procedure does
not work as described, seek the
assistance of a workshop.
Manual transmission
Reverse: with the vehicle stationary,
wait 3 seconds after declutching
before engaging gear. If the gear
does not engage, set the lever in
neutral, release the clutch pedal and
depress again; then repeat gear
selection.When driving, do not use the clutch
pedal as a foot rest; this will cause
substantial clutch wear.
1. Apply the parking brake.
2. Switch off engine then turn
key to ignition switch position
ACC or ON.
3. Remove cap concealing
release button and using a
suitable tool, push the button.
Then move selector lever.
On variants with SHIFT LOCK
button3, push button and
move selector lever.

Page 107 of 153

10-7Vehicle care
Diesel fuel system, bleeding
It is possible to restart the engine if
the tank has been run dry.
With vehicle stationary, turn key to
ignition switch position ON for more
than 5 seconds, then turn to START.
If engine does not start, wait
approx.15 seconds before repeating
starting procedure.
If the engine will still not start, seek
the assistance of a workshop.
Bulb replacement
Before replacing a bulb, switch off
ignition and relevant switch.
Only hold new bulbs at base! Do not
touch the bulb glass with bare hands.
Replacement bulb must be in
accordance with data on base of
defective bulb. Do not exceed
wattage given on bulb base.
Headlamps
Battery removal
Diesel engines: for headlamp bulb
replacement on the battery side, it is
necessary to first disconnect and
remove the battery then remove the
coolant expansion tank and fuse box.
1. Switch off ignition and exterior
lamps.
2. Open bonnet and disconnect
battery by detaching negative (-)
terminal followed by positive (+)
terminal.3. Unscrew the retaining bolt using a
suitable tool and remove battery,
coolant expansion tank and fuse
box.
When reinstalling the battery,
reconnect the positive (+) terminal
first and then the negative (-)
terminal.