clock OPEL MERIVA 2009 User Guide

161
Driving and operation
Check that the coupling ball bar is correctly installedzGreen marking on rotary knob must
point towards white ma rking on coupling
ball bar
z There must be no gap between the
rotary handle and the coupling ball bar
z The coupling ball bar must be firmly
engaged in the opening
z The coupling ball bar must be locked
and the key removed
Picture no: 12421t.tif
Eye for break-away stopping cable
In the case of trailers/caravans with brakes,
attach breakaway stopping cable to eye.
Picture no: 13670t.tif
Dismounting the coupling ball bar
Open the protective flap and turn the key
to position 1 to unlock the coupling ball bar
3 159, Fig. 12416 T.
Pull out rotary handle and turn clockwise
as far as it will go. Pull out coupling ball bar
downwards.
Insert the sealing plug in the opening for
the coupling ball bar. Close the socket
3 159, Fig. 15271 S.
9 Warning
Towing a caravan/trailer is only
permitted with a properly fitted coupling
ball bar. If the coupling ball bar cannot
be correctly fitted, please contact a
workshop for assistance.

169
Self-help, vehicle care
Picture no: 17918s.tif
Screw in the towing eye anticlockwise as far
as it will go until it stops in a horizontal
position.
Attach a tow rope 3 – or better still a tow
rod 3 – to the eye.
The towing eye may only be used for
towing and not for recovery of the vehicle. Switch on ignition to release steering
column lock and to permit operation of
brake lamps, horn an
d windscreen wipers.
Gear lever in neutral.
Picture no: 17897s.tif
When the engine is not running,
considerably more force is needed to brake
and steer.
To prevent the entry of exhaust fumes from
the towing vehicle, switch on the air
recirculation 3 and close the windows.
Contact a workshop for assistance.
Caution
Drive slowly. Do not drive jerkily.
Excessive tractive force can damage
the vehicle.

170 Self-help, vehicle careIf the automatic clutch has been manually
disengaged in vehicles with manual
automated transmission 3 towing is not
permitted 3134. In this case, contact a
workshop for assistance immediately.
After towing, unscrew towing eye by
rotating clockwise and insert and close the
cap.
Picture no: 14199s.tif
Towing another vehicle
Attach a tow rope 3 – or better still a tow
rod 3 – to the rear towing eye on the right
side of the vehicle underbody, but never to
the rear axle.
Picture no: 17898s.tif
On some versions, the towing eye is located
behind a cover.
Slacken the screw a quarter turn with a
screwdriver (see Fig.) and remove the
cover.
The towing eye may only be used for
towing and not for recovery of the vehicle.
After towing, fit cover 3 and secure with
bolt.
Caution
Drive slowly. Do not drive jerkily.
Excessive tractive force can damage the
vehicle.

186 Self-help, vehicle care
Picture no: 16086s.tif
Dipped beam
1. Open bonnet and engage support.
2. Rotate the cap anticlockwise and remove.
Picture no: 16087s.tif
3. Press the bulb do wn in the holder.
4. Remove bulb with connector from reflector housing.
Picture no: 16088s.tif
5. Detach plug connector from bulb base.
6. Attach connector to new bulb.
7. Insert the bulb with connector so that the lug engages in the recess in the
reflector.
8. Place headlamp protective cover in position and close.

187
Self-help, vehicle care
Picture no: 16089s.tif
Main beam
1. Open bonnet and engage support.
2. Rotate the cap anticlockwise and remove.
Picture no: 16090s.tif
3. Detach plug connector from bulb.
4. Disengage spring wire clip from
retaining lugs by moving it forwards
and swivel it aside.
Picture no: 16091s.tif
5. Remove bulb from reflector housing.
6. When fitting the new bulb, insert lugs in the reflector recesses.
7. Engage spring wire clip, plug connector
onto bulb.
8. Place headlamp protective cover in position and close.

189
Self-help, vehicle care
Picture no: 14220s.tif
3. Detach plug connector from bulb.
4. Disengage spring wire clip from retaining lug and swivel upward.
Picture no: 14221s.tif
5. Remove bulb from reflector housing.
6. When fitting the new bulb, insert lugs in
the reflector recesses.
7. Engage spring wire clip, plug connector onto bulb.
8. Place headlamp protective cover in position and close.
Picture no: 16089s.tif
Parking lamps 1. Open bonnet and engage support.
2. Rotate the main beam headlamp cap anticlockwise and remove.
On vehicles with Xenon headlamps 3 ,
remove headlamp cover cap 3188,
Fig. 14219 S.

193
Self-help, vehicle care
Picture no: 17957s.tif
Fog tail lamp bulb: Rotate bulb
mounting anticlockwise and disengage.
Remove bulb from holder.
6. Fit new bulbs. Click bulb mounting into housing.
7. Connect both plugs. Insert bulb housing with retaining pins in body and fasten
with screws.
Picture no: 17900s.tif
Number plate lamp 1. Insert screwdriver 3 vertically on right-
hand side of bulb housing, exert pressure
towards the right and disengage spring.
Remove the bulb housing downwards.
Picture no: 14232s.tif
2. Rotate bulb holder to left and
disengage.