PEUGEOT 1007 2005 Owners Manual

108 -Accesses
01-10-2005
109
-Accesses
01-10-2005
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine management
system as soon as the ignition has
been switched off and therefore
prevents starting of the vehicle by
anyone who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code is
recognised and starting is possible.
If the system does not function cor-
rectly,
contact a PEUGEOT dealer as
soon as possible.
Changing the battery of the
remote control
Battery ref.: CR1620/3 volts.
The information "battery lat" is given
by an audible signal, accompanied
by a message on the multifunction
display.
To replace the battery, unclip the cas-
ing using a coin at the ring.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Key in ignition
A message on the multi-function dis-
play, accompanied by a buzzer on
opening the driver's door, indicates
that the key has been left in the igni-
tion.
Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park:
F press button B, the courtesy lights
come on and the direction indica-
tors lash for a few seconds.
Programming the remote
control
Following changing of the remote
control battery or disconnection of
the vehicle battery, the remote con-
trol must be reprogrammed.
F Wait at least one minute before
using the remote control.
F Switch on the ignition.
F Press button B or C for at least
ive seconds within the next ten
seconds.
F Switch off the ignition.
F Wait at least one minute before
using the remote control.
The remote control is now working
again.
Do not discard the remote
control batteries, they con-
tain metals which are harm-
ful to the environment.
Take them to a PEUGEOT dealer-
ship, or to any other approved col-
lection point.

108 -Accesses
01-10-2005
109
-Accesses
01-10-2005
CONFIDENTIAL CARD
The conidential card contains the
identiication code necessary for any
work carried out by a PEUGEOT
dealer on the electronic immobiliser
system. This code is hidden by a
ilm, which should be removed only
if necessary.
Keep your card in a safe place,
never inside the vehicle.
Make a careful note of the
number on each key. The
key number is coded on the
label attached to the key.
If the keys are lost, your PEUGEOT
dealer can rapidly supply you with
new keys.
The high frequency remote control
is a sensitive system; do not oper-
ate it while it is in your pocket as
there is a possibility that it may
unlock your vehicle, without you
being aware of it.
The remote control does not oper-
ate when the key is in the ignition,
even when the ignition is switched
off, except for reprogramming.
Do not operate the deadlocking
function if there is anyone inside
the vehicle.
Driving with the doors locked may
make access to the passenger com-
partment by the emergency servic-
es more dificult in an emergency.
As a safety precaution (with chil-
dren on board), remove the ignition
key when you leave the vehicle,
even for a short time.
Do not repeatedly press the but-
ton of your remote control out
of range of your vehicle. You run
the risk of stopping it from work-
ing and the remote control would
have to be reprogrammed. When purchasing a second-hand
vehicle:
- ensure that you are given the
conidential card;
- have the key codes memorised by a PEUGEOT dealer, to ensure that
the keys in your possession are
the only ones which can start the
vehicle.
Do not make any modiications to
the electronic engine immobiliser
system.

108 -Accesses
01-10-2005
109
-Accesses
01-10-2005
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine management
system as soon as the ignition has
been switched off and therefore
prevents starting of the vehicle by
anyone who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code is
recognised and starting is possible.
If the system does not function cor-
rectly,
contact a PEUGEOT dealer as
soon as possible.
Changing the battery of the
remote control
Battery ref.: CR1620/3 volts.
The information "battery lat" is given
by an audible signal, accompanied
by a message on the multifunction
display.
To replace the battery, unclip the cas-
ing using a coin at the ring.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Key in ignition
A message on the multi-function dis-
play, accompanied by a buzzer on
opening the driver's door, indicates
that the key has been left in the igni-
tion.
Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park:
F press button B, the courtesy lights
come on and the direction indica-
tors lash for a few seconds.
Programming the remote
control
Following changing of the remote
control battery or disconnection of
the vehicle battery, the remote con-
trol must be reprogrammed.
F Wait at least one minute before
using the remote control.
F Switch on the ignition.
F Press button B or C for at least
ive seconds within the next ten
seconds.
F Switch off the ignition.
F Wait at least one minute before
using the remote control.
The remote control is now working
again.
Do not discard the remote
control batteries, they con-
tain metals which are harm-
ful to the environment.
Take them to a PEUGEOT dealer-
ship, or to any other approved col-
lection point.

110 -Accesses
01-10-2005
111
-Accesses
01-10-2005
ALARM*
The alarm offers two types of protec-
tion.
-
external ; the alarm sounds if one
of the doors, the bonnet or the
tailgate is opened,
- internal ; the alarm sounds if there
is air movement in the passenger
compartment (a broken window or
movement within the car).
The alarm also has an anti-tamper
function.
If there is an attempt to tamper with
the following equipment:
- the wires to the siren or the control unit, the siren sounds accompa-
nied by lashing of the direction
indicators.
- the battery, the siren sounds.
Complete setting and
disarming of the alarm
Complete setting of the alarm
Switch off the ignition and get out
of the vehicle.
Lock or deadlock the vehicle.
The direction indicators light for two
seconds.
The red indicator light on the switch 1
lashes once a second.
5 seconds later, external protection
is set.
45 seconds later, internal protection
is set.
Note: when the alarm is triggered,
the siren sounds for thirty seconds.
However, after the siren stops, the
alarm remains set. Complete disarming of the alarm
Press the unlocking button on the
remote control.
The direction indicators lash for two
seconds.
The red indicator light on the switch
1
goes out.
Note: if the indicator light continues
to lash after de-activation of the
alarm, it is a sign that the alarm has
been triggered during your absence.
The lashing will stop when the igni-
tion is switched on.
* According to country
When the alarm is set, if
a door, the tailgate or the
bonnet is not closed cor-
rectly, the siren sounds for
a moment. If the vehicle is closed
correctly in the following 45 seconds,
the alarm is set. In all cases, the
alarm is set after 45 seconds.
Automatic setting*
The alarm is set automatically 2 min-
utes after the last door or the boot is
closed.
To prevent the alarm being triggered
when a door or the boot is opened,
the remote control unlocking button
must be pressed again.
Locking the vehicle without
alarm
To lock the vehicle without activating
the alarm (for example when wash-
ing), insert the key in the lock, then
lock it.

110 -Accesses
01-10-2005
111
-Accesses
01-10-2005
Selection of the type of
protection
To set the alarm to external
protection only
If you want to leave a window partial-
ly open, or a pet inside the vehicle,
you need to select external protec-
tion only:
- switch off the ignition,
- within the next ten seconds, press
the control button 1 until the warn-
ing light comes on continuously,
- get out of the vehicle,
- lock or deadlock the vehicle,
- the direction indicators light for two seconds,
- the red indicator light on the switch 1 lashes once a second.
Remote control failure
Unlock the doors using the key.
Open the door.
The alarm is triggered.
Switch on the ignition.
The electronic engine immobiliser
system recognises the key.
The siren stops and the alarm is dis-
armed.
Do not make any modiica-
tions to the alarm system,
this could result in malfunc-
tions.
To de-activate external protection
only
Press the unlocking button on the
remote control.
The direction indicators lash for two
seconds.
The red indicator light on the switch
1
goes out.
Work on the battery
The alarm must not be set when the
battery is disconnected. Otherwise,
the siren will sound.
After reconnecting the battery:
- lock or deadlock, then unlock the
vehicle using the remote control,
- the alarm will be operational again the next time the vehicle is locked
or deadlocked.

112 -Accesses
01-10-2005
113
-Accesses
01-10-2005
ELECTRIC WINDOWS
1 - Driver's electric window
switch.
2 - Passenger electric window switch. Notes:
The electric window controls are not
active when the door concerned is
open.
The movement of a window stops if
the door is opened. A second action
on the electric window control will
only be taken into account when the
door is closed.
The electrical functions of the electric
windows are deactivated approxi-
mately one minute after the ignition
is switched off.
Always remove the key
from the ignition when leav-
ing the vehicle, even for a
short time.
In the event of contact when operat-
ing the windows, you must reverse
the movement of the window. To do
this, press the control concerned.
When the driver operates the pas-
senger window controls, he must en-
sure that no one is preventing correct
closing of the window.
The driver must ensure that pas-
sengers use the electric windows
correctly.
Be aware of children when operating
the windows.
Safety auto-reverse
When the window rises and meets
an obstacle, it stops and partially
lowers again.
Note:
In the case of unwanted opening of
the window on closing or if the win-
dow will not rise, lower it completely
and raise it again immediately, by
pulling the control until the window
closes completely. Continue to press
the control for approximately one
second after closing.
You have two options:
- Manual operation:

Press or pull control 1 gently. The
window stops as soon as the control
is released.
- Automatic operation:
Press or pull control 1 fully. The
window opens or closes completely
when the control is released. Press-
ing the control again stops the move-
ment of the window.

112 -Accesses
01-10-2005
113
-Accesses
01-10-2005
THE "SESAME" DOORS
The exterior and interior handles
only permit triggering of the electric
movement of the door when it is fully
closed or fully open.
Opening and closing of the doors is
accompanied by an audible signal.
Closing from outside
Give a irm, fast push forwards on the
handle, without guiding the door, to
trigger the electric movement of the
door.
Opening from outside
Using your hand, tilt the handle to-
wards the rear of the vehicle and
remove your hand from the handle
when the electric movement of the
door begins.
Locking/Unlocking from inside
Press button
A, the red warning light
comes on when the vehicle is locked
and switches off when it is unlocked.
This locks/unlocks the doors and the
tailgate.
If the vehicle is locked or deadlocked
from outside, the red warning light
lashes and button A does not func-
tion. In this case, use the key or the
remote control for unlocking.
Opening/Closing from inside

The opening and closing operates in
the same way as from outside.
None of the door opening switches
function when the vehicle is dead-
locked.
To open using the interior
handle: tilt the handle, with
the palm of your hand to-
wards the door.

114 -Accesses
01-10-2005
115
-Accesses
01-10-2005
Automatic central locking
The doors can lock automatically
when you are driving (at a speed of
more than 6 mph (10 km/h)).
You can activate or deactivate this
function.
Driving with the doors
locked may make access
to the passenger compart-
ment by the emergency
services more dificult in an
emergency.
Activation
With the ignition on, press and hold
button A.
Activation of the function is accompa-
nied by an audible signal and a mes-
sage on the multifunction display.
Deactivation
With the ignition on, press and hold
button A.
Deactivation of the function is ac-
companied by an audible signal.
"Door open" alert
When the vehicle is moving, a dia-
gram or a message locating the door
on the multifunction display, accom-
panied by a permanent audible sig-
nal and lashing of the courtesy light
warn you that a door or the boot is
not properly closed. Opening/Closing from the front
Press switch
B to open or close the
corresponding door.
Choosing the movement of the door
using the switches:
- pull è opens the door,
- push è closes,
- second press è stops the move-
ment,
- the switches do not function above 3 mph (5 km/h). Opening/Closing using the
remote control
Press button
C or D to open or close
the left or right door.
The opening and closing of the door is
accompanied by an audible signal.
2nd press on button C or D during
opening/closing è interruption of the
movement.
3rd press on button C or D
è movement of the door in the op-
posite direction.
You are advised to use
the remote control or the
switches as much as pos-
sible.

114 -Accesses
01-10-2005
115
-Accesses
01-10-2005
General
recommendations
Always check that it is safe to oper-
ate the door and be sure, in particu-
lar, not to leave children or animals
near the door controls without super-
vision.
When opening the door, with the
window open, ensure that no person,
animal or object is hanging through
the window.
Before any opening or closing and
during any movement of the doors,
ensure that no person, animal or
object is preventing the required
manoeuvre, either inside or outside
the vehicle.
It is imperative that the doors are
operated only when the vehicle is
stationary.
For your safety and for that of your
passengers, you are strongly ad-
vised not to drive with a door open.
The lashing of the courtesy light +
audible warning + "door open" mes-
sage are there to remind you.
Lock your vehicle when using an au-
tomatic carwash.

The doors and the overall
dimensions of the vehicle
Safety/Obstacle detection
The obstacle detection system is
triggered when an obstacle of a cer-
tain physical resistance hinders the
movement of the door.
• If an obstacle is detected while the
door is closing, the door stops then
opens fully.
• If an obstacle is detected while the door is opening, the door stops.
When you have removed the ob-
stacle, complete or restart the ac-
tion using buttons C or D on the
remote control or the switches B.
When open, a door never protrudes
beyond the rear bumper.
When open, a door exceeds the
width of the exterior mirror by 8 mm,
be sure to take this into account
when you park alongside a wall, a
post or a high kerb...

116 -Accesses
01-10-2005
117
-Accesses
01-10-2005
Behaviour in the case of a
steep slope
It is possible to open and close the
doors electrically up to a gradient of
20 %. In the case of a steep slope,
the door may be driven by
its own weight and as a
consequence may open or
close sharply.
Therefore:
• There would not be time for opera- tion of one of the electric controls to
be taken into account.
• There would not be time for the obstacle detection system to be
triggered.
Take care not to leave the vehicle on
a steep slope with the door(s) open
without supervision. If this advice is
not followed, injuries or damage may
occur if a part of the body or an ob-
ject is trapped or caught.
In the event of an impact
The electric controls are deactivated
in the event of an impact. Manual
opening and closing is still possible.
Special features of operation
With the ignition off,
• doors open, power consuming equipment on (radio, lights…),
or
• doors in an intermediate position (door neither fully open nor fully
closed).
After 30 minutes, the vehicle auto-
matically switches to energy econo-
my mode.
However, if your vehicle is on a
slope, with the front of the vehicle
facing up, open the door with care.
The door may open more quickly due
to the incline of the ground.
However, if your vehicle is on a
slope, with the front of the vehicle
facing down, the door may not stay
open and may close again sharply
with the risk of injury.
Before any opening or clos-
ing and during any move-
ment of the doors, ensure
that no person, animal or
object is preventing the required
manoeuvre, either inside or outside
the vehicle. If this advice is not fol-
lowed, injuries or damage may occur
if a part of the body or an object is
trapped or caught.
Electric closing and opening of the
doors is not possible above 3 mph
(5 km/h):
• If you set off with the door(s) open, you must slow down to below the
threshold of 3 mph (5 km/h) in or-
der to close the door(s).
• Any attempt to open a door electri- cally using the interior handle, while
driving, results in the door opening
partially and, as a safety measure,
locking in this position immediately.
Flashing of the courtesy light + au-
dible warning + "door open" mes-
sage accompany this situation. In
order to release the door and be
able to operate it again, you must
slow down to below the threshold
of 3 mph (5 km/h) again.