PEUGEOT 1007 2005 Owner's Manual

24 -Instruments and controls
01-10-2005
25
-Instruments and controls
01-10-2005
Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
F
Switch off the ignition,
F Press and hold the trip recorder
re-set button,
F Switch on the ignition.
The display begins a countdown.
When the display shows "= 0" and
the service symbol disappears, re-
lease the button.
Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least ive
minutes, otherwise the zero re-set
will not be registered.Total/trip distance recorder
Briely pressing the button alternates
between the total and trip distance
displays.
To reset the trip distance recorder to
zero, when it is displayed press the
button until zeros appear.
Lighting rheostat
With the lights on, press the button to
vary the intensity of the lighting of the
instruments and controls. When the
lighting reaches the required bright-
ness, release the button.

24 -Instruments and controls
01-10-2005
25
-Instruments and controls
01-10-2005
"2 Tronic" gearbox indicator
This comes on when
the
"AUTO" automat-
ed operation mode is
selected.
It is switched off on
switching to the sequential operation
mode.
"AUTO" and " T" indicator lights Gear lever positions:
"Neutral"
"Reverse"
Sequential operating mode: 1st gear
2nd gear
3rd gear
4th gear
5th gear
"AUTO" indicator light
These lash simultaneously in the
event of a malfunction.
"
T " indicator light
In the automated mode, if
the gearbox detects poor
grip, this indicator light
comes on.

26 -Instruments and controls
01-10-2005
27
-Instruments and controls
01-10-2005
TRIP COMPUTER
Each successive press of the button
marked
"O", located on the end of
the wiper stalk , permits displaying
of the trip computer data in succes-
sion depending on the multifunction
display: If you have the
monochrome screen
A , the following data will appear on
the instrument panel display:
- the remaining range,
- the current consumption,
- the average consumption,
- the average speed.
Monochrome screen A
Zero reset
Press the stalk for more than two
seconds.
Monochrome screen B
- the remaining range
- the distance travelled
- the average consumption
- the current consumption
- the average speed
Zero reset
Press the stalk for more than two
seconds.

26 -Instruments and controls
01-10-2005
27
-Instruments and controls
01-10-2005
Monochrome screen CT
-
the "vehicle" tab with:
• range, current consumption and
the distance still to be driven,
- tab "1" (route "1") with:
• the distance driven, the average consumption and the average
speed calculated over route "1"
- tab "2" (route "2") with the same
features. - the
"Current information" with:
• the range,
• the current consumption,
• the distance still to be driven.
- "Route 1" with:
• the distance travelled,
• the average consumption,
• the average speed,
- "Route 2" with the same features.
Colour screen DT
Zero re-set
When the required route is displayed,
press the button for more than two
seconds.
Range
This shows the distance that can still
be covered with the fuel remaining in
the tank.
Note: this igure may increase if
there is a change in the style of driv-
ing or the road surface, producing a
signiicant drop in current consump-
tion.
When the range is less than 20 miles
(30 km), three segments are dis-
played. After illing with fuel, the
range is displayed when it exceeds
62 miles (100 km).
If horizontal segments are displayed
for long periods instead of digits,
contact a PEUGEOT dealer.
Current consumption
This is the average quantity of fuel con-
sumed during the last few seconds.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
It can be programmed and therefore dis-
played in mpg (litres/100 or in km/litre).
Zero re-set
When the required route is displayed,
press the button for more than two
seconds.
Average consumption
This is the average fuel consump-
tion since the computer was last set
to zero.
It can be programmed and therefore dis-
played in mpg (litres/100 or in km/litre).
Distance travelled
This indicates the distance travelled
since the computer was last set to
zero.

28 -Instruments and controls
01-10-2005
Distance remaining to be travelled
This is the distance remaining to the
inal destination. It can either be cal-
culated by the navigation if guidance
is activated, or entered by the user,
minus the distance covered since the
distance was entered.
Note: if digits are missing, dashes
are displayed in their place.
Average speed
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).
The routes
The routes "1" and ''2'' are independ-
ent but have identical application.
Route "1" for example allows you
to make daily calculations and route
"2" monthly calculations.
Speciic features of the
monochrome screen CT and
the colour screen DT
General menu
Press the "MENU" button to access
the general menu.
Select the icon ''On-board com-
puter'' using the dial, then validate
to access the ''On-board computer''
menu.
The ''On-board computer'' menu of-
fers various choices:
- On-board computer coniguration,
- Diagnostics.
"On-board computer" context
menu
The context menu associated with
the "On-board computer" applica-
tion appears as a superimposed dis-
play when the on-board computer is
the application currently being used
in the main screen window.
Briely press the continuous applica-
tion "On-board computer" button to
select one of the following functions:
- Warning log,
- Distance to destination. On-board computer coniguration
This function allows the distance to
the destination to be input (when
guidance is not activated; otherwise
this information is given by the navi-
gation system) and also changing of
the units of measurement (°C or °F,
km and litres or miles and gallons).
The consumptions (current or average)
can be programmed and therefore dis-
played in mpg (litres/100 or in km/litre).
Diagnostics
This function permits displaying
of the warning log, the equipment
load level and the number of satel-
lites which can be detected by the
system.
Warning log
This summarises the active warning
messages by displaying them in suc-
cession on the multifunction display.
Distance to destination
When guidance is not activated, this
enables an approximate value to be
entered to make all the on-board
computer calculations possible.

29
-Multifunction displays
01-10-2005
MONOCHROME SCREEN A
Presentation
This displays the following information:
- the time,
- the date,
- the outside temperature by press-
ing button 1 or 2 (the temperature
lashes if there is a risk of ice),
- the status of the accesses (doors, boot, ...),
- the warning messages (e.g.: "ASR/ ESP fault") and information messa-
ges (e.g.: "Economy mode") dis-
played temporarily, can be cleared
by pressing button 1 or 2.
If you have the monochrome screen A ,
the trip computer data appears on the
instrument panel display.
Parameter coniguration
Press button 1 for two seconds to
access the settings.
Then, individual presses on this
button allow you to scroll through the
various parameters:
- language in which the information is displayed,
- hour,
- minutes,
- year,
- month,
- day,
- time format (12 or 24 hour mode),
- temperature unit (degrees Celsius or Fahrenheit).
Pressing button 2 allows you to
change the parameter selected.
Maintain the pressure for rapid
scrolling.
After ten seconds without action, the
screen returns to the normal display
and the modiied data is recorded.

30 -Multifunction displays
01-10-2005
31
-Multifunction displays
01-10-2005
MONOCHROME SCREEN B
Presentation
This displays the following information:
- the time,
- the date,
- the outside temperature (if there is
a risk of ice, you are warned by a
message),
- the audio equipment displays,
- the status of the accesses (doors, boot, ...),
- the warning messages (e.g. "Bat- tery charge fault") or information
messages (e.g. "Passenger air bag
deactivated''), displayed temporarily,
can be cleared by pressing but-
ton 1 or 2,
- the trip computer.
Parameter coniguration
Press button 1 for two seconds to
access the settings.
Then, individual presses on this but-
ton allow you to scroll through the
various parameters:
- language in which the information is displayed,
- unit of distance (km or miles),
- unit of temperature (Celsius or Fahrenheit),
- time format (12 or 24 hour mode),
- hour,
- minutes,
- year,
- month,
- day.
Pressing button 2 allows you to
change the parameter selected.
Maintain the pressure for rapid
scrolling.
After ten seconds without action, the
screen returns to the normal display
and the modiied data is recorded.

30 -Multifunction displays
01-10-2005
31
-Multifunction displays
01-10-2005
MONOCHROME SCREEN CT
Parameter configuration
The "Coniguration" menu provides
access to the following parameters:
• "Brightness setting": setting of the brightness of the display,
• "Sound": setting of the voice syn- thesiser (for the male/female voice
parameter: insert the coniguration
CD-Rom); setting of the voice com-
mands,
• "International parameters": setting of the date and time (12 or 24 hour
mode, adjustment of the minutes on
GPS); selection of the units (l/100 - °C
or mpg - °F),
• "Selection of the language": selec- tion of the language of the display,
information and voice commands
(German, English, Spanish,
French, Italian, Dutch, Portuguese:
insert the coniguration CD-rom ).
Presentation
This displays the following informa-
tion:
- the time,
- the date,
- the outside temperature (if there is a risk of ice, you are warned by a
message),
- the audio source displays (radio, CD, ...),
- the telematic system displays (telephone, services, ...),
- the status of the accesses (doors, boot, ...),
- the warning messages (e.g.: "Fuel level low") and vehicle function sta-
tus messages (e.g.: "Passenger air
bag deactivated") displayed tempo-
rarily,
- the trip computer display,
- the satellite navigation system dis- plays. This system is controlled by the
RT3
GPS audio/telephone keypad.
In order to enable you to use all of
your system's functions, you have
two CD-Roms:
- one, "Coniguration", contains the software and the various display
languages and spoken informa-
tion,
- the other, "Navigation", contains the satellite navigation system map
data.
General menu
Press the "MENU" button on the
RT3 audio/telephone to access the
general menu and select one of the
following applications:
- navigation - trafic info,
- audio functions,
- trip computer,
- directory,
- telephone and telematic services,
- coniguration.
For further details regarding these
functions, refer to the corresponding
section. For safety reasons, conig-
uration of the multifunction
displays by the driver must
take place when stationary.

32 -Multifunction displays
01-10-2005
33
-Multifunction displays
01-10-2005
COLOUR SCREEN DT
Presentation
This displays the following informa-
tion:
- the time,
- the date,
- the outside temperature (if there is
a risk of ice, you are warned by a
message),
- the audio source displays (radio, CD, ...),
- the telematic system displays (telephone, services, ...),
- the status of the accesses (doors, boot, ...),
- the warning messages (e.g.: "Fuel level low") and vehicle function status
messages (e.g.: "Passenger air bag
deactivated") displayed temporarily,
- the trip computer display,
- the satellite navigation system dis- plays. This system is controlled by the
RT3
GPS audio/telephone keypad.
In order to enable you to use all of
your system's functions, you have
two CD-Roms:
- one, "Coniguration", contains the software and the various display
languages and spoken information,
- the other, "Navigation", contains the satellite navigation system map
data. General menu
Press the "MENU" button on the
RT3 audio/telephone to access the
general menu and select one of the
following applications:
- navigation - trafic info,
- audio functions,
- trip computer,
- directory,
- telephone and telematic services,
- coniguration,
- map,
- video.
For further details regarding these
functions, refer to the corresponding
section.

32 -Multifunction displays
01-10-2005
33
-Multifunction displays
01-10-2005
Parameter configuration
The
"Display coniguration" menu
provides access to the following pa-
rameters:
• "Select the colours": selection from the palette of colours available for
the display,
• "Brightness and intensity": setting of the brightness and intensity of
the display,
• "Sound": setting of the voice syn- thesiser (for the male/female voice
parameter: insert the coniguration
CD-Rom); setting of the voice com-
mands, activation/deactivation of
the auxiliary input,
• "International parameters": setting of the date and time (12 or 24 hour
mode, adjustment of the minutes
on GPS); selection of the units (l/100 - °C
or mpg - °F),
• "Selection of the language": selec-tion of the language of the display,
information and voice commands
(German, English, Spanish,
French, Italian, Dutch, Portuguese:
insert the coniguration CD-rom). For safety reasons, conigu-
ration of the multifunction
displays by the driver must
take place when stationary.
A FEW DEFINITIONS...
Superimposed display
This is a window which appears tem-
porarily over the current application
to announce a change of status of
another application.
Permanent application
This is the main application currently
in use, displayed as the main screen
window.
Contextual menu
This is a menu, limited to the main
functions of the main application
currently in use, displayed as the
main screen window.