remote control PEUGEOT 1007 2008 User Guide

4
76
ALARM
The alarm offers two types of
protection.
- external ; the alarm sounds if
one of the doors, the bonnet
or the tailgate is opened ,
- internal ; the alarm sounds

if there is air movement in
the passenger compartment
(a broken window or movement
within the car).
The alarm also has an anti-tamper
function.
If there is an attempt to tamper with
the following equipment:
- the wires to the siren or the control unit, the siren sounds
accompanied by fl ashing of the
direction indicators.
- the battery, the siren sounds. Complete setting and
disarming of the alarm
Complete disarming of the alarm
Press the unlocking button on the
remote control.
The direction indicators fl ash for
two seconds.
The red indicator light on the switch

1 goes out.

Note: if the indicator light continues to
fl ash after de-activation of the alarm,
it is a sign that the alarm has been
triggered during your absence. The
fl ashing will stop when the ignition is
switched on.
When the alarm is set,
if a door, the tailgate or
the bonnet is not closed
correctly, the siren sounds
for a moment. If the vehicle is closed
correctly in the following 45 seconds,
the alarm is set. In all cases, the
alarm is set after 45 seconds. Automatic setting
The alarm is set automatically
2 minutes after the last door or the
boot is closed.
To prevent the alarm being triggered
when a door or the boot is opened,
the remote control unlocking button
must be pressed again.
Locking the vehicle without
alarm
To lock the vehicle without activating
the alarm (for example when washing),
insert the key in the lock, then lock it.
Complete setting of the alarm

Switch off the ignition and get out
of the vehicle.
Lock or deadlock the vehicle.
The direction indicators light for
two seconds.
The red indicator light on the switch 1
fl ashes once a second.
5 seconds later, external protection
is set.
45 seconds later, internal protection
is set.

Note: when the alarm is triggered,
the siren sounds for thirty seconds.
However, after the siren stops, the
alarm remains set.

4
77
Selection of the type of
protection Remote control failure
Unlock the doors using the key.
Open the door.
The alarm is triggered.
Switch on the ignition.
The electronic engine immobiliser
system recognises the key.
The siren stops and the alarm is
disarmed.
Do not make any modi-
fi cations to the alarm
system, this could result in
malfunctions.
To de-activate external protection
only
Press the unlocking button on the
remote control.
The direction indicators fl ash for two
seconds.
The red indicator light on the switch

1 goes out. Work on the battery
The alarm must not be set when the
battery is disconnected. Otherwise,
the siren will sound.
After reconnecting the battery:
- lock or deadlock, then unlock
the vehicle using the remote
control,
- the alarm will be operational again the next time the vehicle
is locked or deadlocked.
To set the alarm to external
protection only
If you want to leave a window partially
open, or a pet inside the vehicle, you
need to select external protection
only:
- switch off the ignition,
- within the next ten seconds,
press the control button 1 until
the warning light comes on
continuously,
- get out of the vehicle,
- lock or deadlock the vehicle,
- the direction indicators light for two seconds,
- the red indicator light on the switch 1 fl ashes once a second.

4
78
ELECTRIC WINDOWS

1. Driver’s electric window
switch.

2. Passenger electric window
switch.
One-touch electric window
with safety auto-reverse
You have two options: - Manual mode:
Press or pull switch 1 gently.
The window stops as soon
as the switch is released.
- Automatic mode:
Press or pull switch 1 fully. The win-
dow opens or closes completely
when the switch is released.
Pressing the switch again stops the
movement of the window.
Note: the electrical functions of
the one-touch electric windows are
deactivated approximately one minute
after the ignition is switched off.
Safety auto-reverse
In automatic mode, when the window
rises and meets an obstacle, it stops
and partially lowers again.
In the case of unwanted
opening of the window on
closing or if the window will
not rise, lower it completely
and raise it again immediately, by
pulling the switch until the win-
dow closes completely. Continue to
press the switch for approximately
one second after closing.

The safety auto-reverse function is not
operational during these operations.
You can close all of the
windows using the remote
control when locking
(refer to the section "Access -
§ Remote control key").
The electric window switches are not
active when the door concerned is
open.
The movement of a window stops if
the door is opened. A second action
on the electric window switch will
only be taken into account when the
door is closed. Always remove the key from
the ignition when leaving
the vehicle, even for a short
time.
In the event of contact when opera-
ting the windows, you must reverse
the movement of the window. To do
this, press the switch concerned.
When the driver operates the
passenger window switches, he must
ensure that no one is preventing
correct closing of the window.
The driver must ensure that
passengers use the electric windows
correctly.
Be aware of children when operating
the windows.

4
79
"SESAME" DOORS
The exterior and interior handles
only permit triggering of the electric
movement of the door when it is fully
closed or fully open.
Opening and closing of the doors is
accompanied by an audible signal.
Closing from outside
Give a fi rm, fast push forwards on the
handle, without guiding the door, to
trigger the electric movement of the
door.
Opening from outside
Using your hand, tilt the handle
towards the rear of the vehicle and
remove your hand from the handle
when the electric movement of the
door begins.
Locking/Unlocking from inside
Press button
A , the red warning light
comes on when the vehicle is locked
and switches off when it is unlocked.
This locks/unlocks the doors and the
tailgate.
If the vehicle is locked or dead-
locked from outside, the red warning
light fl ashes and button A does not
function. In this case, use the key or
the remote control for unlocking.
Opening/Closing from inside
The opening and closing operates in
the same way as from outside.
None of the door opening switches
function when the vehicle is dead-
locked.
To open using the interior
handle: tilt the handle, with
the palm of your hand to-
wards the door.

4
80
Automatic central locking
The doors can lock automatically
when you are driving (at a speed of
more than 6 mph (10 km/h).
You can activate or deactivate this
function. Driving with the doors locked
may make access to the
passenger compartment by
the emergency services more
diffi cult in an emergency.
Activation
With the ignition on, press and hold
button A .
Activation of the function is accom-
panied by an audible signal and a
message on the multifunction display.
Deactivation
With the ignition on, press and hold
button A .
Deactivation of the function is
accompanied by an audible signal
and a message on the multifunction
display.
"Door open" alert -
when the vehicle is moving,
by lighting of the "door open"
warning light, accompanied by
an audible signal and a message
on the multifunction display for a
few seconds.
Opening/Closing using the
remote control
Press button C or D to open or close
the left or right door.
The opening and closing of the
door is accompanied by an audible
signal.
2nd press on button C or D during
opening/closing  interruption of the
movement.
3rd press on button C or D  move-
ment of the door in the opposite
direction.
You are advised to use the
remote control or the con-
trols as much as possible.
Opening/Closing from the front
Press switch
B to open or close the
corresponding door.
Choosing the movement of the door
using the controls:
- pull  opens the door,
- push  closes,
- second press  stops the
movement,
- the controls do not function above 3 mph (5 km/h).
If a door or the boot is not
closed properly, you are
warned:
- when the engine is running,
by lighting of the "door open"
warning light, accompanied by
a message on the multifunction
display for a few seconds.

4
83
TAILGATE
Tailgate release
This enables the tailgate to be
unlocked in the event of a central
locking fault.
- Fold back the rear seats to gain access to the lock from inside
the boot,
- Insert a small screwdriver into hole A of the lock to unlock the
tailgate.
"Tailgate open" warning
In this case, or following reconnection
of the battery, with the doors open, it
may be necessary to close the doors
manually, in order to reinitialise them,
and start the engine. If the tailgate is not closed
properly, you are warned:
- with the engine running , by
lighting of the "door open" war-
ning light, accompanied by a
message displayed briefl y on the
multifunction display.
- when the vehicle is moving , by
lighting of the "door open" war-
ning light, accompanied by an
audible signal and a message
displayed briefl y on the multi-
function display.
The tailgate locks automati-
cally when the vehicle speed
reaches 6 mph (10 km/h).
It unlocks when one of the
doors is opened if the speed is below
3 mph (5 km/h) or when the central
locking button on the centre console
is pressed.

When the door has stopped in an
intermediate position (neither fully
open nor fully closed), only the
remote control or the controls per-
mit electric operation of the door.
When closing requests are made
when the door is in a partially open
position, the door may open slightly
before closing.
When closing a door electrically when
the battery is low, you are advised to
guide the door manually. Recharge
the battery as soon as possible.
If the electric controls (remote control
or controls) no longer operate, reini-
tialise the door(s) as follows:

1. Start the engine.

2. Manually open the door(s) fully.

3. Close the door(s) fully.
On completion of this procedure,
electric operation of the doors is
restored.
However, if a problem persists
following this procedure, contact a
PEUGEOT dealer. Simultaneous locking or
unlocking of the tailgate and the
doors
The tailgate is locked or unlocked by
the remote control or from the driver’s
door lock.
To open, press the control
1 and lift
the tailgate.

4
83
TAILGATE
Tailgate release
This enables the tailgate to be
unlocked in the event of a central
locking fault.
- Fold back the rear seats to gain access to the lock from inside
the boot,
- Insert a small screwdriver into hole A of the lock to unlock the
tailgate.
"Tailgate open" warning
In this case, or following reconnection
of the battery, with the doors open, it
may be necessary to close the doors
manually, in order to reinitialise them,
and start the engine. If the tailgate is not closed
properly, you are warned:
- with the engine running , by
lighting of the "door open" war-
ning light, accompanied by a
message displayed briefl y on the
multifunction display.
- when the vehicle is moving , by
lighting of the "door open" war-
ning light, accompanied by an
audible signal and a message
displayed briefl y on the multi-
function display.
The tailgate locks automati-
cally when the vehicle speed
reaches 6 mph (10 km/h).
It unlocks when one of the
doors is opened if the speed is below
3 mph (5 km/h) or when the central
locking button on the centre console
is pressed.

When the door has stopped in an
intermediate position (neither fully
open nor fully closed), only the
remote control or the controls per-
mit electric operation of the door.
When closing requests are made
when the door is in a partially open
position, the door may open slightly
before closing.
When closing a door electrically when
the battery is low, you are advised to
guide the door manually. Recharge
the battery as soon as possible.
If the electric controls (remote control
or controls) no longer operate, reini-
tialise the door(s) as follows:

1. Start the engine.

2. Manually open the door(s) fully.

3. Close the door(s) fully.
On completion of this procedure,
electric operation of the doors is
restored.
However, if a problem persists
following this procedure, contact a
PEUGEOT dealer. Simultaneous locking or
unlocking of the tailgate and the
doors
The tailgate is locked or unlocked by
the remote control or from the driver’s
door lock.
To open, press the control
1 and lift
the tailgate.

4
84
PANORAMIC SUNROOF
This sunroof is a panoramic assembly
which provides maximum brightness
and visibility in the passenger com-
partment.
It consists of two parts:
- a fi xed rear part,
- a moving front part.
Each part has an independent
manual shutter.
The sunroof is controlled electrically
by a dial with 9 opening positions. Operation

To open: turn the dial to the left
(nine possible settings).
Once the roof is open, the front
shutter cannot be closed.

To close: return the control to the
initial position "O" . Reinitialisation
Following reconnection of the bat-
tery, in the event of a malfunction or
in the event of unwanted opening of
the roof on closing, the safety auto-
reverse must be reinitialised:
- place the dial in the fully closed
position (initial position "O" ),
- press the dial immediately,
- continue to press until the roof is fully closed.
Always remove the ignition
key when leaving the vehicle,
even for a short time.
In the event of contact during operation
of the roof, the movement of the roof
must be reversed. To do this, operate
the control concerned.
When the driver operates the roof
control, he must ensure that no one
is preventing the roof from closing
correctly.
The driver must ensure that the
passengers use the sunroof correctly.
Be aware of children when operating
the roof.
Check that the slides are clean
to ensure that the sunroof slides
correctly.
Safety auto-reverse
When the roof meets an obstacle
while closing, it partially opens
again.
You can close the sunroof
using the remote control
when locking (refer to the
corresponding chapter).
The safety auto-reverse function
is not operational during this
operation.

5
91
COURTESY LIGHT

1. Front courtesy light

2. Map reading lights In the permanently on posi-
tion, there are different dura-
tions of lighting:
Boot light
The boot light is located in the left
boot trim.
It comes on automatically when the
boot is opened and switches of auto-
matically when the boot is closed.
Front courtesy light Permanently off.
Permanently on.
In this position, the courtesy
light comes on gradually:
- when the vehicle is unlocked,
- when the key is removed from the ignition,
- when the remote control locking button is pressed, in order to
locate your vehicle.
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed. Map reading lights
With the ignition on, press
the corresponding switch 2 .
- when the ignition is off,
approximately ten minutes,
- in energy economy mode, approximately thirty seconds, - when the engine is running, no limit.

9
128
BATTERY
The batteries contain harm-
ful substances such as sul-
phuric acid and lead. They
must be disposed of in ac-
cordance with regulations and must
never be discarded with household
waste.
Take used remote control and vehi-
cle batteries to a special collection
point.
To start the vehicle from
another battery:
-
Connect the red cable to the positive
(+) terminals of the two batteries,
- Connect the green or black ca-
ble to the negative (-) terminals
of the two batteries,
- Operate the starter, let the en- gine run,
- Wait for the engine to return to idle, then disconnect the cables.
Before disconnecting the
battery, you must wait for
2 minutes after switching off
the ignition.
Never disconnect a terminal when
the engine is running.
Never charge a battery without fi rst
disconnecting the terminals.
Close the windows, the sunroof and
the doors before disconnecting the
battery. If they do not operate nor-
mally following reconnection of the
battery, they must be reinitialised
(see sections "Sesame doors" and
"Sunroof"). After every reconnection of the battery:
- switch on the ignition and wait
1 minute before starting to al-
low the electronic systems to be
initialised. If slight diffi culties are
experienced after this, please
contact a PEUGEOT dealer.
- reinitialise the "2 Tronic" gearbox (refer to the corresponding sec-
tion).

A. Flat battery

B. Slave battery
It is advisable to disconnect
the battery if the vehicle is
not to be used for a period
of more than one month.
To charge the battery using a
battery charger:
- Disconnect the battery,
- Follow the instructions for use
given by the battery charger
manufacturer,
- Reconnect starting with the neg- ative (-) terminal,
- Check that the terminals and connectors are clean. If they are
covered with sulphate (white or
greenish deposit), disconnect
them and clean them.