ignition PEUGEOT 1007 2008 Owner's Manual

Page 79 of 189

4
80
Automatic central locking
The doors can lock automatically
when you are driving (at a speed of
more than 6 mph (10 km/h).
You can activate or deactivate this
function. Driving with the doors locked
may make access to the
passenger compartment by
the emergency services more
diffi cult in an emergency.
Activation
With the ignition on, press and hold
button A .
Activation of the function is accom-
panied by an audible signal and a
message on the multifunction display.
Deactivation
With the ignition on, press and hold
button A .
Deactivation of the function is
accompanied by an audible signal
and a message on the multifunction
display.
"Door open" alert -
when the vehicle is moving,
by lighting of the "door open"
warning light, accompanied by
an audible signal and a message
on the multifunction display for a
few seconds.
Opening/Closing using the
remote control
Press button C or D to open or close
the left or right door.
The opening and closing of the
door is accompanied by an audible
signal.
2nd press on button C or D during
opening/closing  interruption of the
movement.
3rd press on button C or D  move-
ment of the door in the opposite
direction.
You are advised to use the
remote control or the con-
trols as much as possible.
Opening/Closing from the front
Press switch
B to open or close the
corresponding door.
Choosing the movement of the door
using the controls:
- pull  opens the door,
- push  closes,
- second press  stops the
movement,
- the controls do not function above 3 mph (5 km/h).
If a door or the boot is not
closed properly, you are
warned:
- when the engine is running,
by lighting of the "door open"
warning light, accompanied by
a message on the multifunction
display for a few seconds.

Page 84 of 189

4
84
PANORAMIC SUNROOF
This sunroof is a panoramic assembly
which provides maximum brightness
and visibility in the passenger com-
partment.
It consists of two parts:
- a fi xed rear part,
- a moving front part.
Each part has an independent
manual shutter.
The sunroof is controlled electrically
by a dial with 9 opening positions. Operation

To open: turn the dial to the left
(nine possible settings).
Once the roof is open, the front
shutter cannot be closed.

To close: return the control to the
initial position "O" . Reinitialisation
Following reconnection of the bat-
tery, in the event of a malfunction or
in the event of unwanted opening of
the roof on closing, the safety auto-
reverse must be reinitialised:
- place the dial in the fully closed
position (initial position "O" ),
- press the dial immediately,
- continue to press until the roof is fully closed.
Always remove the ignition
key when leaving the vehicle,
even for a short time.
In the event of contact during operation
of the roof, the movement of the roof
must be reversed. To do this, operate
the control concerned.
When the driver operates the roof
control, he must ensure that no one
is preventing the roof from closing
correctly.
The driver must ensure that the
passengers use the sunroof correctly.
Be aware of children when operating
the roof.
Check that the slides are clean
to ensure that the sunroof slides
correctly.
Safety auto-reverse
When the roof meets an obstacle
while closing, it partially opens
again.
You can close the sunroof
using the remote control
when locking (refer to the
corresponding chapter).
The safety auto-reverse function
is not operational during this
operation.

Page 86 of 189

5
86
LIGHTS STALK
Lights off Automatic switching on
of lights.
Side lights Dipped/main beam
headlamps Dipped/Main beam change
Pull the stalk fully towards you.
Front fog lamps and rear fog
lamp
Rotate the ring
B or C forwards to
switch on and backwards to switch
off. The status is displayed by the in-
dicator light on the instrument panel.
Vehicles fi tted with a rear fog
lamp (ring B)
Rear fog lamp
Vehicles fi tted with front fog
lamps and a rear fog lamp (ring C) Front fog lamps (1st rotation
of the ring forwards)
These operate with the side lights
and dipped headlamps.
Lights on
With the ignition off, a buzzer sounds
when the driver’s door is opened, if
you have left your lights on.
If the dipped headlamps remain
on, with the ignition off, they will be
switched off automatically after thirty
minutes maximum to prevent dis-
charging of the battery.
This can only operate with the dipped
and main beam headlamps.
Front and rear lights
Selection is by turning ring
A .

Page 92 of 189

5
90
Windscreen wash
Pull the wiper stalk towards you. The
windscreen wash, then the wind-
screen wipers, operate for a speci-
fi ed time.
Low wash-wipe/headlamp wash
fl uid level
On vehicles fi tted with headlamp
washers, this is indicated by an audi-
ble signal or a message on the multi-
function display.
This information is given each time
the front or rear wash-wipe control is
operated, until the reservoir is fi lled.
When you stop, fi ll the wash-wipe/
headlamp wash reservoir or have it
fi lled. Do not cover the rain sen-
sor located on the wind-
screen behind the interior
mirror.
When using an automatic car wash,
switch off the ignition.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic wipe.
Rear windscreen wiper
Turn ring A to the fi rst notch
for intermittent wiping.
When reverse gear is engaged, if the
windscreen wipers are in operation,
the rear wiper will start wiping.
Turn ring A past the fi rst
notch; the windscreen wash
then the windscreen wiper
operate for a fi xed period.
Automatic windscreen wipers
In
AUTO mode, the windscreen wip-
ers operate automatically and adapt
their speed to the intensity of the
rainfall .
Activation
Activation of the function is accom-
panied by a message on the multi-
function display.

The automatic windscreen wipers
function must be reactivated if the
ignition has been switched off for
more than one minute, by press-
ing the stalk downwards.
Deactivation
Deactivation of the function is ac-
companied by a message on the
multifunction display.
The function is deactivated when the
windscreen wipers stalk is moved to
position I , 1 or 2 .

In the event of malfunction of the
automatic windscreen wipers, the
windscreen wipers will operate in in-
termittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Rear windscreen wash To activate or deactivate
this function, go to the
multi-function display
confi guration menu.
If there is a signifi cant ac-
cumulation of snow or ice
and when using a bicycle
carrier on the tailgate, deactivate the
automatic rear wiping by going to the
multifunction display confi guration
menu.
Special position of the front
windscreen wiper
In the minute following switching off
of the ignition, any action on the stalk
positions the wipers in the centre of
the windscreen.
This action enables you to position
the wiper blades for winter parking,
cleaning or replacement (See corre-
sponding section).
To park the wipers after this has
been done, switch on the ignition and
operate the stalk.

Page 93 of 189

5
90
Windscreen wash
Pull the wiper stalk towards you. The
windscreen wash, then the wind-
screen wipers, operate for a speci-
fi ed time.
Low wash-wipe/headlamp wash
fl uid level
On vehicles fi tted with headlamp
washers, this is indicated by an audi-
ble signal or a message on the multi-
function display.
This information is given each time
the front or rear wash-wipe control is
operated, until the reservoir is fi lled.
When you stop, fi ll the wash-wipe/
headlamp wash reservoir or have it
fi lled. Do not cover the rain sen-
sor located on the wind-
screen behind the interior
mirror.
When using an automatic car wash,
switch off the ignition.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic wipe.
Rear windscreen wiper
Turn ring A to the fi rst notch
for intermittent wiping.
When reverse gear is engaged, if the
windscreen wipers are in operation,
the rear wiper will start wiping.
Turn ring A past the fi rst
notch; the windscreen wash
then the windscreen wiper
operate for a fi xed period.
Automatic windscreen wipers
In
AUTO mode, the windscreen wip-
ers operate automatically and adapt
their speed to the intensity of the
rainfall .
Activation
Activation of the function is accom-
panied by a message on the multi-
function display.

The automatic windscreen wipers
function must be reactivated if the
ignition has been switched off for
more than one minute, by press-
ing the stalk downwards.
Deactivation
Deactivation of the function is ac-
companied by a message on the
multifunction display.
The function is deactivated when the
windscreen wipers stalk is moved to
position I , 1 or 2 .

In the event of malfunction of the
automatic windscreen wipers, the
windscreen wipers will operate in in-
termittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Rear windscreen wash To activate or deactivate
this function, go to the
multi-function display
confi guration menu.
If there is a signifi cant ac-
cumulation of snow or ice
and when using a bicycle
carrier on the tailgate, deactivate the
automatic rear wiping by going to the
multifunction display confi guration
menu.
Special position of the front
windscreen wiper
In the minute following switching off
of the ignition, any action on the stalk
positions the wipers in the centre of
the windscreen.
This action enables you to position
the wiper blades for winter parking,
cleaning or replacement (See corre-
sponding section).
To park the wipers after this has
been done, switch on the ignition and
operate the stalk.

Page 94 of 189

5
91
COURTESY LIGHT

1. Front courtesy light

2. Map reading lights In the permanently on posi-
tion, there are different dura-
tions of lighting:
Boot light
The boot light is located in the left
boot trim.
It comes on automatically when the
boot is opened and switches of auto-
matically when the boot is closed.
Front courtesy light Permanently off.
Permanently on.
In this position, the courtesy
light comes on gradually:
- when the vehicle is unlocked,
- when the key is removed from the ignition,
- when the remote control locking button is pressed, in order to
locate your vehicle.
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed. Map reading lights
With the ignition on, press
the corresponding switch 2 .
- when the ignition is off,
approximately ten minutes,
- in energy economy mode, approximately thirty seconds, - when the engine is running, no limit.

Page 95 of 189

6
92
HORN
Press one of the spokes of the stee-
ring wheel.
HAZARD WARNING LIGHTS
Press the button, the direction indica-
tors fl ash.
They can operate with the ignition
off.
Automatic lighting of hazard
warning lights
When braking in an emergency, de-
pending on the force of deceleration,
the hazard warning lights come on au-
tomatically. They switch off automati-
cally the fi rst time you accelerate.
It is also possible to switch them off
by pressing the button on the fascia.
TYRE UNDER-INFLATION DETECTION
Sensors fi tted in each valve check
the pressure of the tyres while dri-
ving and trigger a warning in the
event of malfunction (speed above
12 mph (20 km/h)).
The tyre under-infl ation detection
system is an aid to driving which does
not replace the need for the driver to
be vigilant or to drive responsibly.
Flat tyre This warning light comes
on on the instrument panel,
accompanied by an audible
signal and a message on the
multifunction display locating
the wheel concerned.

 Check the tyre pressures as
soon as possible.
This check must be carried out when
the tyres are cold.

Page 96 of 189

6
92
HORN
Press one of the spokes of the stee-
ring wheel.
HAZARD WARNING LIGHTS
Press the button, the direction indica-
tors fl ash.
They can operate with the ignition
off.
Automatic lighting of hazard
warning lights
When braking in an emergency, de-
pending on the force of deceleration,
the hazard warning lights come on au-
tomatically. They switch off automati-
cally the fi rst time you accelerate.
It is also possible to switch them off
by pressing the button on the fascia.
TYRE UNDER-INFLATION DETECTION
Sensors fi tted in each valve check
the pressure of the tyres while dri-
ving and trigger a warning in the
event of malfunction (speed above
12 mph (20 km/h)).
The tyre under-infl ation detection
system is an aid to driving which does
not replace the need for the driver to
be vigilant or to drive responsibly.
Flat tyre This warning light comes
on on the instrument panel,
accompanied by an audible
signal and a message on the
multifunction display locating
the wheel concerned.

 Check the tyre pressures as
soon as possible.
This check must be carried out when
the tyres are cold.

Page 99 of 189

6
95
If this warning light comes on on
the instrument panel and the in-
dicator light on the button comes
on, this indicates that the ASR
and ESP systems are disarmed.
TRACTION CONTROL (ASR) AND DYNAMIC STABILITY CONTROL (ESP)
Operation of the ASR and ESP
systems The warning light fl ashes if
the ASR or ESP is activated. Disarming
In exceptional conditions (starting a
vehicle which is bogged down, stuck
in snow, on soft ground, ...), it may
be advisable to disarm the ASR and
ESP systems, so that the wheels can
move freely and regain grip.

 Press the "ESP OFF" button,
located in the centre of the
fascia.
Reactivation
These systems are reactivated au-
tomatically each time the ignition is
switched back on or from 30 mph
(50 km/h).

 Press the "ESP OFF" button again
to reactivate them manually. Operating fault
If this warning light comes
on, accompanied by an au-
dible signal and a message
on the multifunction display,
this indicates a malfunction of these
systems.
Have the systems checked by a
PEUGEOT dealer.
The ESP/ASR systems offer excep-
tional safety in normal driving, but
this should not encourage the driver
to take extra risks or drive at high
speed.
The correct functioning of these
systems depends on observation of
the manufacturer’s recommenda-
tions regarding the wheels (tyres
and rims), the braking components,
the electronic components and the
PEUGEOT assembly and operation
procedures.
After an impact, have these systems
checked by a PEUGEOT dealer.
Activation of the ASR and ESP
systems
When the ignition is on, the ASR and
ESP systems are always active.
These systems are linked and com-
plement the ABS.
The ASR system optimises drive to
prevent the wheels skidding, by acting
on the brakes of the drive wheels and
on the engine. It also allows the direc-
tional stability of the vehicle to be im-
proved on acceleration.
If there is a variation between the tra-
jectory followed by the vehicle and
that required by the driver, the ESP
system automatically acts on the en-
gine and the brake of one or more
wheels, in order to put the vehicle
back on course, within the limits of
the laws of physics.

Page 100 of 189

6
96
SEAT BELTS
Additional seat belt warnings
Version with monochrome display
A or C

1. Multifunction display.

2. Warning light indicating that a
passenger’s seat belt is not fas-
tened or has been unfastened.

3. Front passenger’s seat belt not
fastened warning.

4. Rear right passenger’s seat belt
unfastened warning.

5. Rear left passenger’s seat belt
unfastened warning.
Fastening

 Slide your arm along the door
and take hold of the seat belt at
the base. This action must be
carried out with the door closed
to avoid any risk of trapping.

 Insert the buckle in the stalk.

 Check that the seat belt is fas-
tened correctly by pulling the
strap.
Unfastening

 Press the red button on the
stalk.
Front seat belts
Safety in the event of a frontal impact
has been improved by the introduc-
tion of pre-tensioning and force-li-
miting front seat belts. Depending
on the seriousness of the impact, the
pre-tensioning system instantly tight-
ens the seat belts fi rmly against the
body of the occupant.
The pre-tensioning seat belts are
armed when the ignition is on.
The force-limiting device reduces the
pressure of the seat belt against the
occupant’s body in the event of an
accident.

Page:   < prev 1-10 11-20 21-30 31-40 41-50 next >