ECO mode PEUGEOT 1007 2008 Owners Manual

FAMILIARISATION
DRIVING SAFELY
Speed limiter Cruise control

1. Speed limiter mode Selection/
Off.

2. Decreasing of the programmed
value.

3. Increasing of the programmed
value.

4. Speed limiter On/Off.
1. Cruise control mode Selection/
Off.

2. Decreasing of the programmed
value.

3. Increasing of the programmed
value.

4. Cruise control On/Off.
In order to be programmed or
activated, the vehicle speed must
be above 25 mph (40 km/h), with
at least fourth gear engaged on the
manual gearbox (second gear for the
"2 Tronic" gearbox). Display on the instrument panel
The cruise control or speed limiter
mode appears on the instrument
panel when it is selected.

Cruise control

Speed limiter
The values must be set with the
engine running.

 107

 105

1
23
Lack of oil
If "OIL" fl ashes and the service
warning light comes on, accompanied
by an audible signal and a message
on the multifunction display, this
indicates a lack of oil which could
damage the engine.
If the lack of oil is confi rmed by a
check using the dipstick, it is essential
that the level is topped up.
Engine oil level indicator
When the ignition is switched on,
the engine oil level is indicated for
approximately 5 seconds after the
service indicator display.
Oil level gauge fault
Check the oil level using the dip-
stick.
If "OIL --" fl ashes, this indicates a
malfunction of the engine oil level
gauge.
Consult a PEUGEOT dealer.
INSTRUMENT PANEL DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator
- total distance recorder (total and trip distances).
The level read on the dipstick
will only be correct if the ve-
hicle is on level ground and
the engine has been off for
more than 15 minutes.
Oil level correct

Note: the trip distance is displayed
for thirty seconds, when the ignition
is switched off, on opening and
closing the driver’s door as well as
on locking the vehicle.
It also displays the "2 Tronic" gear-
box positions and operating modes
selected, as well as the information
relating to the cruise control or speed
limiter when one of these functions is
active.

3
48
AUTOMATIC AIR CONDITIONING
The air conditioning can only operate when the engine is running.
1. Automatic "comfort" programme
We recommend that you use this
mode, it provides optimised auto-
matic control of all of the following
functions: passenger compartment
temperature, air fl ow, air distribution
and air intake, in accordance with the
comfort value that you have chosen.
This system is designed to operate
effectively in all seasons, with the
windows closed. Press the
"AUTO" button.
The "AUTO" symbol is
displayed. The automatic comfort
programme may not be
suffi cient for rapid de-icing or
demisting of the windscreen
and side windows (humidity,
several passengers, ice, etc.).
In this case, select the automatic
visibility programme. The button 3
indicator light comes on.
The system automatically controls
the air conditioning and the fl ow of air
and provides optimum distribution of
the ventilation to the windscreen and
side windows. It deactivates the air
recirculation.
To exit this programme, press
button 3 again or press the "AUTO"
button, the indicator light on the
button is switched off and "AUTO" is
displayed.

Note: for your comfort, when the
engine is switched off, the settings are
retained until the engine is switched
on again, if the temperature in the
passenger compartment has not
altered signifi cantly; otherwise, opera-
tion resumes in automatic mode.
When the engine is cold, to prevent
too great a distribution of cold air, the
air fl ow will only reach its optimum
level gradually. 3. Automatic "visibility" programme
Automatic operation
The value indicated on
the display corresponds
to a level of comfort and
not to a temperature
in degrees Celsius or
Fahrenheit.
2. Temperature adjustment On entering the vehicle, if
the interior temperature is
much colder or warmer than
is comfortable, there is no
need to change the value displayed
in order to reach the required level of
comfort. The system eliminates the
temperature difference automatically
and as quickly as possible.
Press the
"+" and "-" buttons to
change this value. A setting around
the value 22 enables optimum
comfort to be obtained. However,
depending on your requirements, a
setting between 18 and 24 is usual.

4
78
ELECTRIC WINDOWS

1. Driver’s electric window
switch.

2. Passenger electric window
switch.
One-touch electric window
with safety auto-reverse
You have two options: - Manual mode:
Press or pull switch 1 gently.
The window stops as soon
as the switch is released.
- Automatic mode:
Press or pull switch 1 fully. The win-
dow opens or closes completely
when the switch is released.
Pressing the switch again stops the
movement of the window.
Note: the electrical functions of
the one-touch electric windows are
deactivated approximately one minute
after the ignition is switched off.
Safety auto-reverse
In automatic mode, when the window
rises and meets an obstacle, it stops
and partially lowers again.
In the case of unwanted
opening of the window on
closing or if the window will
not rise, lower it completely
and raise it again immediately, by
pulling the switch until the win-
dow closes completely. Continue to
press the switch for approximately
one second after closing.

The safety auto-reverse function is not
operational during these operations.
You can close all of the
windows using the remote
control when locking
(refer to the section "Access -
§ Remote control key").
The electric window switches are not
active when the door concerned is
open.
The movement of a window stops if
the door is opened. A second action
on the electric window switch will
only be taken into account when the
door is closed. Always remove the key from
the ignition when leaving
the vehicle, even for a short
time.
In the event of contact when opera-
ting the windows, you must reverse
the movement of the window. To do
this, press the switch concerned.
When the driver operates the
passenger window switches, he must
ensure that no one is preventing
correct closing of the window.
The driver must ensure that
passengers use the electric windows
correctly.
Be aware of children when operating
the windows.

5
88
Daytime lights *
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
Automatic switching on of
lights
The side lights and dipped beam
headlamps switch on automatically if
the light is poor and when the wind-
screen wipers operate continuously.
They switch off when the light be-
comes bright enough or the wind-
screen wipers are switched off.

In foggy weather or in
snow, the brightness
sensor can detect suffi -
cient light, the lights will
not come on automati-
cally.

Do not cover the brightness sen-
sor, coupled with the rain sensor,
located in the centre of the wind-
screen behind the interior mirror.
It is used for automatic switching
on of the lights.
Coupling with the Follow Me
Home lighting
The association with the automatic
lighting function provides the follow
me home lighting with the following
additional options:
- selection of maintaining of the lighting for a duration of 15, 30
or 60 seconds in the vehicle pa-
rameters of the multifunction dis-
play confi guration menu (except
in the case of the monochrome
display A for which the duration
is pre-set),
- automatic activation of the fol- low me home lighting when the
automatic lighting function is in
operation.
Activation
Turn the lighting control to the
"
AUTO " position.
Disarming
Turn the lighting control to a position
other than " AUTO ".
Operating fault
If the brightness sensor does not
function correctly, the lights come on
accompanied by the service warning
light, an audible signal and a mes-
sage on the multifunction display.
Consult a PEUGEOT dealer. Operating fault
If the brightness sensor does not
function correctly, the lights come on
accompanied by the service warning
light, an audible signal and a mes-
sage on the multifunction display.
Contact a PEUGEOT dealer.
Do not cover the brightness
sensor, coupled with the rain
sensor, located in the centre
of the windscreen behind
the interior mirror; the as-
sociated functions would no
longer be controlled.
This warning light comes on
on the instrument panel.
The instruments and controls (instru-
ment panel, multifunction display,
air conditioning control panel, ...)
are only lit on switching to the auto-
matic switching on of the lights mode
or when the lights are switched on
manually.
* According to country.

5
88
Daytime lights *
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
Automatic switching on of
lights
The side lights and dipped beam
headlamps switch on automatically if
the light is poor and when the wind-
screen wipers operate continuously.
They switch off when the light be-
comes bright enough or the wind-
screen wipers are switched off.

In foggy weather or in
snow, the brightness
sensor can detect suffi -
cient light, the lights will
not come on automati-
cally.

Do not cover the brightness sen-
sor, coupled with the rain sensor,
located in the centre of the wind-
screen behind the interior mirror.
It is used for automatic switching
on of the lights.
Coupling with the Follow Me
Home lighting
The association with the automatic
lighting function provides the follow
me home lighting with the following
additional options:
- selection of maintaining of the lighting for a duration of 15, 30
or 60 seconds in the vehicle pa-
rameters of the multifunction dis-
play confi guration menu (except
in the case of the monochrome
display A for which the duration
is pre-set),
- automatic activation of the fol- low me home lighting when the
automatic lighting function is in
operation.
Activation
Turn the lighting control to the
"
AUTO " position.
Disarming
Turn the lighting control to a position
other than " AUTO ".
Operating fault
If the brightness sensor does not
function correctly, the lights come on
accompanied by the service warning
light, an audible signal and a mes-
sage on the multifunction display.
Consult a PEUGEOT dealer. Operating fault
If the brightness sensor does not
function correctly, the lights come on
accompanied by the service warning
light, an audible signal and a mes-
sage on the multifunction display.
Contact a PEUGEOT dealer.
Do not cover the brightness
sensor, coupled with the rain
sensor, located in the centre
of the windscreen behind
the interior mirror; the as-
sociated functions would no
longer be controlled.
This warning light comes on
on the instrument panel.
The instruments and controls (instru-
ment panel, multifunction display,
air conditioning control panel, ...)
are only lit on switching to the auto-
matic switching on of the lights mode
or when the lights are switched on
manually.
* According to country.

5
91
COURTESY LIGHT

1. Front courtesy light

2. Map reading lights In the permanently on posi-
tion, there are different dura-
tions of lighting:
Boot light
The boot light is located in the left
boot trim.
It comes on automatically when the
boot is opened and switches of auto-
matically when the boot is closed.
Front courtesy light Permanently off.
Permanently on.
In this position, the courtesy
light comes on gradually:
- when the vehicle is unlocked,
- when the key is removed from the ignition,
- when the remote control locking button is pressed, in order to
locate your vehicle.
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed. Map reading lights
With the ignition on, press
the corresponding switch 2 .
- when the ignition is off,
approximately ten minutes,
- in energy economy mode, approximately thirty seconds, - when the engine is running, no limit.

7
104
Switching to automated mode Reinitialisation
Following disconnection of the battery,
the gearbox must be reinitialised: The brake pedal must be
pressed while starting the
engine.
Never select neutral
N while
the vehicle is moving.
Only engage reverse gear R with the
vehicle immobilised and the brake
pedal pressed.
In all cases, it is imperative that you
apply the handbrake in order to im-
mobilise the vehicle.
On a steep gradient, it is preferable
to switch to sequential mode.
"Auto sequential" mode
In the automated mode, you can re-
sume control temporarily at any time
using the steering wheel controls.
The use of these controls permits
manual selection of the gears in situa-
tions which require a faster change-
down than that offered in automated
mode (arrival at a roundabout, exit
from a car park with a steep gradient,
overtaking...).
The gearbox engages the gear
requested if the engine speed
permits it.
"AUTO" is still displayed
on the instrument panel.
After a few moments, the gearbox
again controls the gears automatically.
Stopping the vehicle
Before switching off the engine, you
can:
- move to position N to leave the
gearbox in neutral.
- leave a gear engaged, such as fi rst or reverse.
In both cases, it is imperative that you
apply the handbrake to immobilise
the vehicle. Operating anomaly
With the ignition on, the fl ashing of

"AUTO" and lighting of the service
warning light, accompanied by an
audible signal and a message on the
multifunction display, indicate a gear-
box malfunction.
Contact a PEUGEOT dealer without
delay.
If you press the accelera-
tor pedal beyond the point
of resistance, the gearbox
selects the gear below to
permit sharper acceleration. - switch on the ignition,
"AUTO"
and "-" appear on the instrument
panel display,
- press the brake pedal,
- wait approximately 30 seconds until "N" or a gear appears on
the instrument panel display,
- release the brake pedal.
The gearbox is operational again.
Automated mode
After using the sequential mode, you
can return to the automated mode by
selecting position
A .

"AUTO" and the gear engaged ap-
pear on the instrument panel display.
The gearbox then operates in auto-
active mode, without any action on
the part of the driver.
It continuously selects the gear most
suited to the following parameters:
- driving style,
- road characteristics,
- vehicle load.
To optimise driving comfort and ob-
tain the most suitable gear, avoid
sharp variations in the pressure on
the accelerator pedal.

7
106
Operating fault
If a speed limiter malfunction occurs,
the speed is replaced by fl ashing
dashes. Contact a PEUGEOT dealer
to have the system checked.
Activating/deactivating the limiter

 Switch the speed limiter on by
pressing button 4 .
Programming

 Place the dial 1 in the LIMIT posi-
tion. The limiter is not yet active.
By default, the display indicates
the last speed programmed: Return to normal driving

 Turn dial 1 to position "0" : the
speed limiter mode is deselected.
The display returns to the distance
recorder.
In the event of a steep descent
or sharp acceleration, the
speed limiter will not be able
to prevent the vehicle from
exceeding the programmed speed.
In any event, the speed limiter cannot
replace the need to observe speed
limits, nor can it replace the need for
vigilance and responsibility on the
part of the driver.
The driver must remain alert and stay
in complete control of his vehicle.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly.
- never fi t one mat on top of another.


Set the speed value by pressing but-
ton 2 or 3 (e.g.: 70 mph (110 km/h).
You can then change the programmed
speed using buttons 2 and 3 :
- by + or - 1 mph (1 km/h) = short press,
- by + or - 5 mph (5 km/h) = long press,
- in steps of + or - 5 mph (5 km/h) = maintained press. Exceeding the programmed
speed
Pressing the accelerator pedal to
exceed the programmed speed will
not have any effect, unless you press
the pedal
fi rmly passing the point of
resistance .
The speed limiter is deactivated tempo-
rarily and the programmed speed,
which is still displayed, fl ashes.
Returning to the programmed speed,
by means of intentional or uninten-
tional deceleration of the vehicle,
cancels the fl ashing automatically
and reactivates the speed limiter.

 Switch the speed limiter off by
pressing button 4 : the display
confi rms that it is off (OFF).

 Switch the speed limiter back on
by pressing button 4 again.

7
108
Exceeding the programmed speed
Intentional or unintentional exceeding
of the programmed speed results in
fl ashing of the programmed speed on
the display.
Returning to the programmed speed,
by means of intentional or uninten-
tional deceleration of the vehicle,
cancels the fl ashing automatically.
Using the accelerator:

 exceed the memorised speed
until the required speed is
reached,

 press button 2 or 3 .
Programming

 Place switch 1 in the CRUISE
position. The cruise control is
not yet active and no speed has
been memorised. The display
indicates: Cancelling the cruise control

 Switch the cruise control off by
pressing button 4 : the display
confi rms that it is off (OFF).
When changing the memo-
rised reference speed by
means of a maintained
press, pay attention as the
speed can increase or de-
crease rapidly.
Do not use the cruise control on slip-
pery roads or in heavy traffi c.
In the event of a steep slope, the
cruise control cannot prevent the
vehicle from exceeding the pro-
grammed speed.
In any event, the cruise control
cannot replace the need to comply
with speed limits, nor can it replace
the need for vigilance and responsi-
bility on the part of the driver.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly.
- never fi t one mat on top of another.
It is advisable to keep your feet near
the pedals.

 Set the programmed speed by
accelerating to the required
speed, then press button 2 or 3
(e.g.: 70 mph (110 km/h)).
Return to normal driving

 Turn dial 1 to position "0" : the
cruise control mode is dese-
lected. The display returns to the
distance recorder. Operating fault
If a cruise control malfunction occurs,
the speed is replaced by fl ashing
dashes.
Contact a PEUGEOT dealer to have
the system checked.
You can then change the programmed
speed using buttons 2 and 3 :
- by + or - 1 mph (1 km/h) = short press,
- by + or - 5 mph (5 km/h) = long press,
- in steps of + or - 5 mph (5 km/h) = maintained press. Reactivating the cruise control

 Switch the cruise control back on
by pressing button 4 again.