air conditioning PEUGEOT 1007 2008 Owners Manual

FAMILIARISATION
DRIVING POSITION

1. Steering wheel adjustment.

2. Headlamp adjustment.

3. Cruise control/speed limiter
switches.

4. "2 Tronic" gearbox steering
wheel controls.

5. Lights and direction indicators
controls.

6.
Adjustable and closing central vents.

7. Windscreen de-icing and
demisting vent.

8. Multifunction display.
Passenger seat belts unfastened/not fastened
warning lights.

9. Passenger front air bag.

10. Passenger "Sesame" door
electric control.

11. Bonnet release.

12.
Glove box/Audio/video sockets/
Disarming of the passenger air bag.

13. Handbrake.

14. Deactivation of the interior
alarm or card holder.

15. Deactivation of the rear parking
assistance.
Central locking from the inside.

Deactivation of the ESP/ASR system.

16. Heating or air conditioning
controls.

17. Audio RD4 or RT4 GPS audio/
telephone.

18. Hazard warning lights.

–
FAMILIARISATION

I require...
Heating or Manual air conditioning

Air distribution Air fl ow
Air recirculation/Intake
of exterior air
Temperature Manual AC

HOT

COLD

DEMISTING
DE-ICING
VENTILATE
Recommended interior settings

3
43
VENTILATION

1. Windscreen de-icing or
demisting vent.

2. Side window de-icing or
demisting vents.

3. Side vents.

4. Central vents.

5. Air outlets to the front footwells.

6. Air outlets to the rear footwells.

7. Temperature sensor. Recommendations for use
If the interior temperature remains
very high following a long period
parked in the sun, do not hesitate to
ventilate the passenger compartment
for a few minutes.
For an even air distribution, make
sure that you do not block the out-
side air inlet grille, the vents and the
air outlets to the footwells.
In certain cases of particularly arduous
use (towing the maximum load on a
steep gradient in a high tempera-
ture), cutting off the air conditioning
permits recovery of the engine power
and therefore improvement of the
towing capacity.
Ensure that the passenger compart-
ment fi lter, located underneath the
windscreen, in the engine compart-
ment, is in good condition. Have the
fi lter elements replaced regularly
(refer to the chapter "Checks - § Checks").
If you drive in a dusty environment,
change them twice as often. We recommend the use of a
combined passenger compartment
fi lter. By means of its second special
active fi lter, it contributes to the
purifi cation of the air breathed by the
occupants and to the cleanness of the
passenger compartment (reduction
of allergic symptoms, unpleasant
odours and oily deposits).
Operate the air conditioning system for
5 to 10 minutes, once or twice a month,
to keep it in perfect working order.
To guarantee correct operation of
your air conditioning system, we also
recommend that you have it checked
regularly.
The condensation created by the
air conditioning results in a fl ow of
water underneath the vehicle when
stationary which is perfectly normal.
If the system does not produce
cold air, do not use it and contact a
PEUGEOT dealer.
Do not cover the temperature sen-
sor
7 , it is used for regulation of the
air conditioning.
The air conditioning system
does not contain chlorine
and does not present any
danger to the ozone layer.

3
46
1. Air conditioning on/off
MANUAL AIR CONDITIONING
The air conditioning can only operate
when the engine is running.
2. Temperature adjustment Turn the control from blue
(cold) to red (hot) to adjust
the temperature to your
requirements.
Version with button and indicator light Version with manual control
The air conditioning is
designed to operate
effectively in all seasons,
with the windows closed.
In summer, it enables the
temperature to be lowered and in
winter, above 0 °C, it increases the
effectiveness of the demisting.
Press the switch, the indicator light
comes on.

The air conditioning does not
operate while the air fl ow adjust-
ment control 3 is in position "0".

3
48
AUTOMATIC AIR CONDITIONING
The air conditioning can only operate when the engine is running.
1. Automatic "comfort" programme
We recommend that you use this
mode, it provides optimised auto-
matic control of all of the following
functions: passenger compartment
temperature, air fl ow, air distribution
and air intake, in accordance with the
comfort value that you have chosen.
This system is designed to operate
effectively in all seasons, with the
windows closed. Press the
"AUTO" button.
The "AUTO" symbol is
displayed. The automatic comfort
programme may not be
suffi cient for rapid de-icing or
demisting of the windscreen
and side windows (humidity,
several passengers, ice, etc.).
In this case, select the automatic
visibility programme. The button 3
indicator light comes on.
The system automatically controls
the air conditioning and the fl ow of air
and provides optimum distribution of
the ventilation to the windscreen and
side windows. It deactivates the air
recirculation.
To exit this programme, press
button 3 again or press the "AUTO"
button, the indicator light on the
button is switched off and "AUTO" is
displayed.

Note: for your comfort, when the
engine is switched off, the settings are
retained until the engine is switched
on again, if the temperature in the
passenger compartment has not
altered signifi cantly; otherwise, opera-
tion resumes in automatic mode.
When the engine is cold, to prevent
too great a distribution of cold air, the
air fl ow will only reach its optimum
level gradually. 3. Automatic "visibility" programme
Automatic operation
The value indicated on
the display corresponds
to a level of comfort and
not to a temperature
in degrees Celsius or
Fahrenheit.
2. Temperature adjustment On entering the vehicle, if
the interior temperature is
much colder or warmer than
is comfortable, there is no
need to change the value displayed
in order to reach the required level of
comfort. The system eliminates the
temperature difference automatically
and as quickly as possible.
Press the
"+" and "-" buttons to
change this value. A setting around
the value 22 enables optimum
comfort to be obtained. However,
depending on your requirements, a
setting between 18 and 24 is usual.

3
49
Press this button to switch
off the air conditioning.
Automatic operation of the
air conditioning is resumed
when the button is pressed
again. The symbol "A/C" is displayed.
4. Air conditioning on/off
Pressing this button several
times in succession enables
the air fl ow to be directed in
turn towards:
- the windscreen and the side windows (de-icing or demisting),
- the windscreen, the side windows, the vents and the footwells,
- the windscreen, the side windows and the footwells,
5. Air distribution adjustment Press buttons
"+" or "-"
respectively to increase
or reduce the air fl ow.
The air fl ow symbol, the fan, fi lls
progressively in relation to the value
requested.
6. Air fl ow adjustment
Press the air fl ow
"-" button 6 until
the fan symbol is empty.
This action switches off all of the
functions of the air conditioning
system, with the exception of the rear
screen demisting 9 .
Avoid driving with the air conditioning
switched off for long periods.
Pressing the air fl ow "+" button 6 again
or the "AUTO" button reactivates the
system with the values set before it
was switched off.
7. Switching the system off
Control using the manual
buttons
It is possible to adjust one or more
functions manually while leaving the
other functions in automatic mode.
The
"AUTO" button indicator light
switches off.
Switching to manual mode may result
in discomfort (temperature, humidity,
odour, condensation) and does not
provide optimum comfort.
To return to automatic mode, press
the "AUTO" button. Press this button for
recirculation of the interior
air. The air recirculation
symbol
8 is displayed.
Air recirculation enables the passenger
compartment to be isolated from
exterior odours and smoke.
Avoid prolonged recirculation of
interior air (risk of condensation or
deterioration of the air quality).
Press this button again or press the

"AUTO" button to resume automatic
management of the intake of air.
8. Air intake/Air recirculation
With the engine running,
press this button to demist
the rear screen and the
exterior mirrors. The
indicator light on button 9
comes on.
Demisting switches off automatically
in relation to the exterior temperature
and to prevent an excessive
consumption of current.
It is possible to stop operation of the
demisting before it is switched off
automatically by pressing the button
again.
If the engine is switched off before the
demisting is switched off automatically,
the demisting will resume the next
time the engine is switched on.
9. Demisting the rear screen and
the mirrors
- the footwells,
- the centre vents, the side vents
and the footwells,
- the centre and side vents.

5
88
Daytime lights *
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
Automatic switching on of
lights
The side lights and dipped beam
headlamps switch on automatically if
the light is poor and when the wind-
screen wipers operate continuously.
They switch off when the light be-
comes bright enough or the wind-
screen wipers are switched off.

In foggy weather or in
snow, the brightness
sensor can detect suffi -
cient light, the lights will
not come on automati-
cally.

Do not cover the brightness sen-
sor, coupled with the rain sensor,
located in the centre of the wind-
screen behind the interior mirror.
It is used for automatic switching
on of the lights.
Coupling with the Follow Me
Home lighting
The association with the automatic
lighting function provides the follow
me home lighting with the following
additional options:
- selection of maintaining of the lighting for a duration of 15, 30
or 60 seconds in the vehicle pa-
rameters of the multifunction dis-
play confi guration menu (except
in the case of the monochrome
display A for which the duration
is pre-set),
- automatic activation of the fol- low me home lighting when the
automatic lighting function is in
operation.
Activation
Turn the lighting control to the
"
AUTO " position.
Disarming
Turn the lighting control to a position
other than " AUTO ".
Operating fault
If the brightness sensor does not
function correctly, the lights come on
accompanied by the service warning
light, an audible signal and a mes-
sage on the multifunction display.
Consult a PEUGEOT dealer. Operating fault
If the brightness sensor does not
function correctly, the lights come on
accompanied by the service warning
light, an audible signal and a mes-
sage on the multifunction display.
Contact a PEUGEOT dealer.
Do not cover the brightness
sensor, coupled with the rain
sensor, located in the centre
of the windscreen behind
the interior mirror; the as-
sociated functions would no
longer be controlled.
This warning light comes on
on the instrument panel.
The instruments and controls (instru-
ment panel, multifunction display,
air conditioning control panel, ...)
are only lit on switching to the auto-
matic switching on of the lights mode
or when the lights are switched on
manually.
* According to country.

5
88
Daytime lights *
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
Automatic switching on of
lights
The side lights and dipped beam
headlamps switch on automatically if
the light is poor and when the wind-
screen wipers operate continuously.
They switch off when the light be-
comes bright enough or the wind-
screen wipers are switched off.

In foggy weather or in
snow, the brightness
sensor can detect suffi -
cient light, the lights will
not come on automati-
cally.

Do not cover the brightness sen-
sor, coupled with the rain sensor,
located in the centre of the wind-
screen behind the interior mirror.
It is used for automatic switching
on of the lights.
Coupling with the Follow Me
Home lighting
The association with the automatic
lighting function provides the follow
me home lighting with the following
additional options:
- selection of maintaining of the lighting for a duration of 15, 30
or 60 seconds in the vehicle pa-
rameters of the multifunction dis-
play confi guration menu (except
in the case of the monochrome
display A for which the duration
is pre-set),
- automatic activation of the fol- low me home lighting when the
automatic lighting function is in
operation.
Activation
Turn the lighting control to the
"
AUTO " position.
Disarming
Turn the lighting control to a position
other than " AUTO ".
Operating fault
If the brightness sensor does not
function correctly, the lights come on
accompanied by the service warning
light, an audible signal and a mes-
sage on the multifunction display.
Consult a PEUGEOT dealer. Operating fault
If the brightness sensor does not
function correctly, the lights come on
accompanied by the service warning
light, an audible signal and a mes-
sage on the multifunction display.
Contact a PEUGEOT dealer.
Do not cover the brightness
sensor, coupled with the rain
sensor, located in the centre
of the windscreen behind
the interior mirror; the as-
sociated functions would no
longer be controlled.
This warning light comes on
on the instrument panel.
The instruments and controls (instru-
ment panel, multifunction display,
air conditioning control panel, ...)
are only lit on switching to the auto-
matic switching on of the lights mode
or when the lights are switched on
manually.
* According to country.

8
116
CHECKS
Handbrake Where the handbrake travel
is too great or there is a re-
duction in the performance
of the system, the hand-
brake should be adjusted,
even between services.
Have the system checked by a
PEUGEOT dealer. Manual gearbox
This does not require an oil
change. Have the level checked
in accordance with the manu-
facturer’s servicing schedule. Air filter and passenger compartment filter
Particle emission filter (Diesel)
It is imperative that maintenance of
the particle emission fi lter is carried
out by a PEUGEOT dealer in accord-
ance with the manufacturer’s servicing
schedule. Brake pads
Brake pad wear depends
on the style of driving, in
particular for vehicles which
are used in town, over short
distances.
Brake disc/drum wear status
For any information relating to the
wear of the surfaces of the discs and
drums, contact a PEUGEOT dealer. Oil filter
Change the fi lter regular-
ly, in accordance with the
servicing schedule.
It may be necessary to check
the thickness of the pads,
even between services.
Unless there is a leak in the circuit, a
drop in the brake fl uid level indicates
that the brake pads are worn.
Only use products recom-
mended by PEUGEOT or
products of equivalent quali-
ty and characteristics.
To ensure best performance
from components as important as the
braking system, PEUGEOT selects
and offers quite specifi c products.
To prevent damage to the electrical
units, high pressure washing of the
engine compartment is strictly pro-
hibited .
At the start of winter, have
your battery checked by a
PEUGEOT dealer.
Refer to the servicing book-
let for information on the re-
placement interval for these
components.
Depending on the environment (dusty
atmosphere...) and the use of the ve-
hicle (urban driving...), change them
twice as often, if necessary (refer to
the "Engines" paragraph).
A clogged passenger compartment fi l-
ter may have an adverse effect on the
performance of the air conditioning sys-
tem and produce unpleasant odours.
To check the main levels
and certain components,
in accordance with the
manufacturer’s servic-
ing schedule, refer to the pages of
the servicing booklet which corre-
spond to your vehicle’s engine.
Following prolonged opera-
tion of the vehicle at very
low speed or at idle, you
may, in exceptional circum-
stances, notice steam coming from
the exhaust during acceleration. This
has no effect on the performance of
the vehicle or on the environment.
Battery