fold seats PEUGEOT 1007 2008 Owners Manual

3
54
REAR SEATS
Seat back angle adjustment
Tilt the control C and adjust the angle
to the comfort or loading position.
Release the control to lock. Folding/Placing in the
"fully folded" position
Place the head restraint in the low
position.
Position the seat belt buckle as close
as possible to the strap return.

Move the seat as far back as
possible using the bar A or the
handle B .
Fold the seat back onto the seat
cushion tilting control C fully.

Note: you can lock the seat back in
this position by pressing on it.
Push the control D upwards to
release the rear feet.
Place the seat in the "fully folded"
position.
When driving, the seat is retained in
this position by the side strut.
Table position
Place the head restraint in the low
position.
Fold the seat back onto the seat
cushion tilting control
C fully.

Note: you can lock the seat back in
this position by pressing on it.
Forwards-backwards adjustment
Lift the bar
A and slide the seat
forwards or backwards.
From the boot, you can press the red
handle B and slide the seat forwards
or backwards.
This manoeuvre makes folding of the
seat when loading the boot easier.

3
55
Never drive with the head
restraints removed, they
must be in place and correctly
adjusted.
Locked Released
In order to ensure that the
seat covers have a long
service life, do not leave
the seat in the table or "fully
folded" position after loading.
Avoid placing luggage on the seats
when they are in the table position.
REAR HEAD RESTRAINTS
The rear head restraints can be
removed and have two positions;
- high, position for use
- low, storage position
Repositioning the seat
Press the control D upwards to check
that the rear feet are released.
Tilt the folded seat rearwards.

The rear feet are secured automatically.
Check that the seat is secured
correctly.
Raise the seat back, releasing it fi rst
by pulling the control C . To raise a head restraint, pull it
upwards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high
position, push the lug and pull it
upwards.
To refi t it, engage the head restraint
rods in the holes taking care to remain
in the centreline of the seat back.

3
67
4 - Seat cushion trims Fitting

 Position the new trim on the seat
cushion or on the seat back.

 Engage the zip pull, located at
the base of the seat cushion or
seat back.

 Guide the zip pull along the three
sides of the seat cushion or seat
back.

 Position the velcro on the last
side of the seat cushion or seat
back trim.

On the rear seats, take care to
position the velcro correctly so
that the ISOFIX mountings are not
covered.

 Fold down the zip pull tab in
the seat cushion or seat back
location. 6 - Rear side storage
compartment cover trims
Removal

 Remove the tab from the zip pull,
located at the base of the seat
cushion or seat back.

 Guide the zip pull along the three
sides of the seat cushion or seat
back.

 Remove the zip pull.

 Pull on the last side to detach the
velcro, then remove the old seat
cushion or seat back trim.
Removal

 Open the cover to 45°.

 Unclip the lug located under the
cover.

 Remove the old cover trim.
Refi tting

 Open the cover to 45°.

 Position the new trim on the cover
by means of the two notches.

 Tilt the trim on the cover.

 Clip the lug located under the
cover.
Some Cameleo seat trims
can be dry cleaned. Please
ask a PEUGEOT dealer for
details.
5 - Seat back trims
Follow these instructions starting,
for each seat, with the complete
seat cushion removal and fi tting
operations, then repeat them for the
seat back.

6
97
Seat belt not fastened warning If the driver and/or the
front passenger has
not fastened his seat
belt, the corresponding
warning light comes
on when the ignition is on, then, at a
speed above 12 mph (20 km/h), this
is accompanied by an audible signal
the volume of which increases (for ap-
proximately two minutes) and a mes-
sage on the multifunction display.

Note: a bag or an animal placed on
the front passenger seat may trigger
lighting of the warning light.
Seat belt unfastened warning
If the driver and/or one
of the passengers has
unfastened his seat
belt, the corresponding
warning light comes on
when the engine is running, then, at a
speed above 12 mph (20 km/h), this
is accompanied by an audible signal
the volume of which increases (for ap-
proximately two minutes) and a mes-
sage on the multifunction display. Rear seat belts
The rear seats are fi tted with two
three-point inertia reel seat belts.
The retaining of the rear seat belt
buckle by the sliding block makes
folding down or complete folding of
the seats easier.
Fastening

 Pull the strap, then insert the
buckle in the stalk.

 Check that the seat belt is
fastened correctly by pulling the
strap.
Unfastening

 Press the red button on the
stalk.
Version with colour display
If the driver and/or one of the pas-
sengers has not fastened (or has
unfastened) his seat belt, a message
appears on the multifunction display.