PEUGEOT 1007 DAG 2005 Owner's Guide

34 -Audio equipment and telematics
01-10-2005
35
-
Audio equipment and telematics
01-10-2005
AUDIO RD3
Stalk movement
Function
1 - Press Increase volume.
2 - Press Decrease volume.
3 - Press Sound cut-off (mute); restoring of the sound by pressing a bu tton.
4 - Press Automatic search of higher frequencies (radio).
Selection of the next track (CD/CD changer).
Continuous pressure until release: accelerated forwards play (CD/C
D changer).
5 - Press Automatic search of lower frequencies (radio).
Selection of the previous track (CD/CD changer).
Continuous pressure until release: accelerated backwards play (CD/C
D changer).
6 - Press Displaying of the trip computer information.
Press for more than 2 seconds: resetting of the route displayed to
zero.

34 -Audio equipment and telematics
01-10-2005
35
-Audio equipment and telematics
01-10-2005
Button
Function
A Radio on/off.
B - Reduction in volume.
C + Increase in volume.
D RDS RDS function on/off.
Press for more than 2 seconds: regional following mode (REG) on/of
f.
E TA Trafic information priority (TA) on/off.
Press for more than 2 seconds: PTY function on/off.
F 5
Ejection of CD.
G ¯Selection of bass, treble, loudness, sound distribution and a
utomatic volume correction.
H 5Increase of the functions associated with button
G.
I 6Decrease of the functions associated with button
G.

36 -Audio equipment and telematics
01-10-2005
37
-Audio equipment and telematics
01-10-2005
Button
Function
J 8Manual and automatic search of higher frequency
Selection of next CD track and of the PTY (radio)
K MAN Manual/automatic operation of buttons J and L
L 7Manual and automatic search of lower frequency
Selection of previous CD track and of the PTY (radio)
M CH. CD Selection of CD changer
Press for more than 2 seconds: random play (RDM)
N CD Selection of the CD source
Press for more than 2 seconds: random play (RDM)
O Radio Selection of the radio source. Selection of wavebands FM1, FM2,
FMast, AM
Press for more than 2 seconds: automatic storing of stations (autosto re)
1 to 6 1 2 3 4 5 6 Selection of station stored in memory
Press for more than 2 seconds: storing of a station in memory
1 to 5 1 2 3 4 5 Selection of the CDs in the CD changer

36 -Audio equipment and telematics
01-10-2005
37
-Audio equipment and telematics
01-10-2005
GENERAL FUNCTIONS
On/off
With the ignition key
in the accessories or
ignition position, press
button
A to switch the
set on or off.
The set can operate for 30 minutes
without the vehicle ignition being
switched on.
Anti-theft system
The audio system is coded in such a
way that it can operate only on your
vehicle. It would not function if itted
to another vehicle.
The anti-theft system is automatic
and requires no action on your
part. Press button
G sev-
eral times in succes-
sion to access the
bass ( BASS), treble
(TREB) , loudness
(LOUD) , fader (FAD) ,
balance ( BAL) and
automatic volume
correction settings.
Exit from audio mode is automatic
after a few seconds without pressing
any button, or by pressing button G
after coniguration of the automatic
volume correction.
Note: bass, treble and loudness set-
tings are speciic to each source. It
is possible to set them differently for
radio, CD or CD changer.
AUDIO SETTINGS
ADJUSTING THE VOLUME
When "BASS" is
displayed, press but-
ton H or I to vary the
setting.
- "BASS -9" for a
minimum bass set-
ting,
- "BASS 0" for a normal setting,
- "BASS +9" for a maximum bass
setting.
Adjusting the bass
Press the button C to
increase the volume,
or button B to de-
crease it.
Continuous pressure
on buttons B and C al-
lows a gradual adjust-
ment of the volume. Adjusting the treble
When
"TREB" is displayed, press
button H or I to vary the setting.
- "TREB -9" for a minimum treble
setting,
- "TREB 0" for a normal setting,
- "TREB +9" for a maximum treble
setting.
Adjusting the loudness
This function automatically empha-
sises bass and treble tones.
Press button H or I to switch the func-
tion on or off.

38 -Audio equipment and telematics
01-10-2005
39
-Audio equipment and telematics
01-10-2005
Adjusting the front/rear sound
distribution (Fader)
When
"FAD" is displayed, press but-
ton H or I.
Button H increases the volume at
the front.
Button I increases the volume at the
rear.
Press button O.
Selecting radio modeRADIO
Notes on radio reception
Your car radio is subject to pheno-
mena which do not affect domestic
radio sets. Both AM and FM recep-
tion are subject to various forms of
interference. This is no relection on
the quality of the equipment, but is due
to the nature of the signals and the
way in which they are transmitted.
On MW/LW, interference may be
noticed when passing under high
voltage power lines or bridges, or in
tunnels.
On FM, interference may be the result
of increasing distance from the trans-
mitter, delection of the signals by
obstacles (mountains, hills, buildings,
etc.), or of being in an area which is
not covered by a transmitter. Selecting a waveband
Press button
O several times in suc-
cession to select wavebands FM1,
FM2, FMast and AM.
Automatic station search
Briely press button J or L to search
for the station immediately above or
below. By continuing to press the
button in the direction selected, you
will obtain continuous scrolling of the
frequency.
The scrolling stops at the irst sta-
tion found as soon as the button is
released.
If the TA trafic program is selected,
only stations broadcasting this type
of program are selected.
Searching for a station occurs irst
in "LO" sensitivity (selection of the
most powerful transmitters) during
scanning of the waveband, then in
"DX" sensitivity (selection of the
weakest and most distant transmit-
ters).
To make a direct search in "DX" sen-
sitivity, press button J or L twice.
Adjusting the right/left sound
distribution (Balance)
When
"BAL" is displayed, press but-
ton H or I.
Button H increases the volume on
the right-hand side.
Button I increases the volume on the
left-hand side.
Automatic volume correction
This function enables the volume to
be automatically adjusted depending
on the level of noise produced by the
speed of the vehicle.
Press buttons H or I to switch the
function on or off.

38 -Audio equipment and telematics
01-10-2005
39
-Audio equipment and telematics
01-10-2005
Adjusting the front/rear sound
distribution (Fader)
When
"FAD" is displayed, press but-
ton H or I.
Button H increases the volume at
the front.
Button I increases the volume at the
rear.
Press button O.
Selecting radio modeRADIO
Notes on radio reception
Your car radio is subject to pheno-
mena which do not affect domestic
radio sets. Both AM and FM recep-
tion are subject to various forms of
interference. This is no relection on
the quality of the equipment, but is due
to the nature of the signals and the
way in which they are transmitted.
On MW/LW, interference may be
noticed when passing under high
voltage power lines or bridges, or in
tunnels.
On FM, interference may be the result
of increasing distance from the trans-
mitter, delection of the signals by
obstacles (mountains, hills, buildings,
etc.), or of being in an area which is
not covered by a transmitter. Selecting a waveband
Press button
O several times in suc-
cession to select wavebands FM1,
FM2, FMast and AM.
Automatic station search
Briely press button J or L to search
for the station immediately above or
below. By continuing to press the
button in the direction selected, you
will obtain continuous scrolling of the
frequency.
The scrolling stops at the irst sta-
tion found as soon as the button is
released.
If the TA trafic program is selected,
only stations broadcasting this type
of program are selected.
Searching for a station occurs irst
in "LO" sensitivity (selection of the
most powerful transmitters) during
scanning of the waveband, then in
"DX" sensitivity (selection of the
weakest and most distant transmit-
ters).
To make a direct search in "DX" sen-
sitivity, press button J or L twice.
Adjusting the right/left sound
distribution (Balance)
When
"BAL" is displayed, press but-
ton H or I.
Button H increases the volume on
the right-hand side.
Button I increases the volume on the
left-hand side.
Automatic volume correction
This function enables the volume to
be automatically adjusted depending
on the level of noise produced by the
speed of the vehicle.
Press buttons H or I to switch the
function on or off.

38 -Audio equipment and telematics
01-10-2005
39
-Audio equipment and telematics
01-10-2005
Manual station search
Manual storing of stations in the
memory
Select the station required.
Press one of the buttons
"1" to "6"
for more than two seconds.
The sound stops then becomes audi-
ble again, conirming that the station
has been stored in the memory. Press button
O down
for more than two
seconds.
Your radio automati-
cally stores the six stations with the
strongest signal in FM. These sta-
tions are stored in the FMast wave-
band.
If it is not possible to ind 6 stations,
the remaining memories are empty.
Automatic storing of FM stations
in the memory (autostore)
Recalling stations stored in the
memory
For each waveband, briely press
one of the buttons
"1" to "6" to recall
the corresponding station.RDS
Using the RDS (Radio Data
System) function on FM
Radio Data System allows you to
continue listening to the same station
whatever frequency it is using for the
region you are going through.
Briely press the "RDS"
button to switch the
function on or off.
The multifunction display will show:
- "RDS" if the function is selected,
-
"RDS" lashing or "(RDS)" if the
function is selected but not available.
Press the "MAN" button.
Briely press button J or L to in-
crease or decrease the frequency
displayed.
By continuing to press the button
in the direction selected, you will
obtain continuous scrolling of the
frequency.
The scrolling stops at the irst sta-
tion found as soon as the button is
released.
Pressing the "MAN" button again
returns you to automatic station
search.
RDS station following
The display indicates the name of
the station selected. When the RDS
function is active, the radio continual-
ly searches for the transmitter which
transmits the station selected with
the best reception.

40 -Audio equipment and telematics
01-10-2005
41
-Audio equipment and telematics
01-10-2005
Press the
"TA" button
briely to switch the
function on or off.
The multifunction display will show:
- "TA" if the function is selected,
- "TA" lashing or "(TA)" if the func-
tion is selected but not available.
Any trafic information lash will be
given priority, whatever source you
are listening to (radio, CD or CD
changer).
If you wish to interrupt a message,
press the "TA" button; this switches
the function off.
Note: the volume of the trafic
information is independent of the
volume of normal radio listening.
You can adjust it using the volume
button. The setting will be stored
and will be used when the next
messages are broadcast.
Trafic information program (TA) Regional following mode (R
EG)
When they are part of a network,
certain stations broadcast regional
programs in the various areas they
serve. With regional following mode
you can keep listening to the same
program.
Press the "RDS" button for more
than two seconds to switch the func-
tion on or off.
With FM selected,
press the "TA" but-
ton for more than two
seconds to switch this
function on or off.
Search by type of program (PTY)
This allows you to listen to stations
broadcasting a speciic type of program
(news, culture, sport, rock etc.).
To search for a
PTY program:
- select the PTY function,
- briely press button J or L to scroll
down the list of the various types of
programs offered,
- when the program of your choice is displayed, keep button J or L
pressed for more than two seconds
to carry out an automatic search
(after an automatic search the PTY
function is switched off).
In PTY mode the different types of
programs can be stored in memory.
To do this, press the preselection
buttons "1" to "6" for more than two
seconds. Briely press the corre-
sponding button to recall the type of
program stored in the memory.
EON system
This connects stations which are part
of the same network. It enables the
broadcasting of trafic information or
of a type of program by a station that
is part of the same network as the sta-
tion to which you are listening.
This service is available when you
have selected the TA trafic informa-
tion program or the PTY search by
type of program function.

40 -Audio equipment and telematics
01-10-2005
41
-Audio equipment and telematics
01-10-2005
COMPACT DISC
Selecting CD mode
After insertion of a disc, printed face
upwards, the player starts automati-
cally.
If a disc is already
inserted, press but-
ton N.
Ejection of a disc Accelerated play
Keep button
J or L pressed for for-
wards or backwards accelerated
play.
Accelerated play stops as soon as
the button is released.
Press button F to
eject the disc from the
player.
Selecting a track
Press button J to select the next
track.
Press button L to return to the start
of the current track or to select the
previous track. The use of copied compact
discs may cause malfunc-
tions.
Insert circular compact discs
only.
Random play (RDM)
When the CD player is selected,
keep button
N pressed for two sec-
onds. The tracks will be played in
random sequence. Pressing the
button again for two seconds returns
you to normal play.
Random play mode is de-activated
each time the audio equipment is
switched off.

42 -Audio equipment and telematics
01-10-2005
43
-Audio equipment and telematics
01-10-2005
CD CHANGER
Selecting CD changer mode
Press button M.
Selecting a disc
Press one of the buttons "1" to "5"
on the radio to select the correspond-
ing disc.
Press button J to select the next
track.
Press button L to return to the start
of the current track or to select the
previous track.
Selecting a track Accelerated play
Keep button
J or L pressed for for-
wards or backwards accelerated
play.
Accelerated play stops as soon as
the button is released.
Random play (RDM)
When the CD changer is selected,
keep button M pressed down for two
seconds. The tracks will be played
in random sequence. Pressing the
button again for two seconds returns
you to normal play.
The use of copied compact
discs may cause malfunc-
tions.
Insert circular compact discs
only.