Peugeot 1007 Dag 2007 Owner's Guide

1
24
Service indicator
This indicates when the next service is due in accordance with the manu-facturer's servicing schedule.
The point at which the next service is due is calculated from the last indica-tor zero reset. It is determined by two parameters:
- the distance travelled,- the time which has elapsed since the last service.
Operation
When the ignition is switched on, the spanner symbolising the servicing operations comes on; the distance recorder display indicates the number of miles (rounded off) remaining until the next service.
Example: 4,800 miles/km remain before the next service. For five sec-onds after the ignition is switched on, the display indicates:
10 seconds after the ignition was switched on, the distance recorder resumes its normal operation and the display indicates the total or trip distance.
The distance remaining to the next service is less than 500 miles/1,000 km.
Example: 400 miles/900km remain before the next service.
For 5 seconds after the ignition is switched on, the display indicates:
10 seconds after the ignition was switched on, the distance recorder resumes its normal operation and the spanner remains lit.
It indicates that a service must be carried out soon. The display indi-cates the total or trip distance.
The service is overdue.
The spanner flashes for 5 seconds each time the ignition is switched on.
Example: the service is overdue by 300 miles/km, your vehicle must be serviced as soon as possible.
For 5 seconds after the ignition is switched on, the display indicates:
10 seconds after the ignition was switched on, the distance recorder resumes its normal operation and the spanner remains lit. The display indi-cates the total or trip distance.
The distance remaining before the next service may be weighted by the time factor, depending on the user's driving habits.
The spanner may also come on if more than two years have elapsed since the last service.

1
25
Service indicator zero re-set
Your PEUGEOT dealer carries out this operation after each service.
However, if you carry out the service yourself, the re-set procedure is as follows:
 Switch off the ignition,
 Press and hold the trip recorder re-set button,
 Switch on the ignition.
The display begins a countdown.
When the display shows "=0", release the button; the spanner dis-appears.
Total/trip distance recorder
Briefly pressing the button alternates between the total and trip distance displays.
To reset the trip distance recorder to zero, when it is displayed press the button until zeros appear.
Lighting rheostat
With the lights on, press the button to vary the intensity of the lighting of the instruments and controls. When the lighting reaches the required bright-ness, release the button.
After this operation, if you wish to disconnect the bat-tery, lock the vehicle and wait for at least five minutes, otherwise the zero re-set will not be registered.

1
26
"2 Tronic" gearbox indicator
This comes on when the "AUTO" auto-mated operation mode is selected.
It is switched off on switching to the sequential operation mode.
It flashes if a malfunction occurs.
Gear lever positions:
"Neutral"
"Reverse"
Sequential operating mode
1st gear
2nd gear
3rd gear
4th gear
5th gear
"AUTO" indicator light

1
27
TRIP COMPUTER
Each press of the button, located on the end of the wiper stalk, permits displaying of the trip computer data in succession depending on the mul-tifunction display:
- the remaining range,- the current consumption,- the distance travelled,- the average consumption,- the average speed.
Monochrome screen A
Zero reset
Press the stalk for more than two seconds to reset the distance trav-elled, the average consumption and the average speed to zero.

1
28
- the "Current information" with:• the range,• the current consumption,• the distance still to be driven.- "Route 1" with:• the distance travelled, • the average consumption, • the average speed,- "Route 2" with the same features for a second route.
Monochrome screen C and colour screen DT
Route zero reset
When the required route is displayed, press the button for more than two seconds.
Range
This shows the distance that can still be covered with the fuel remaining in the tank.
Current consumption
This is the average quantity of fuel con-sumed during the last few seconds.
This function is displayed only when the vehicle is travelling at a speed greater than 20 mph (30 km/h).
It can be programmed and therefore dis-played in mpg (litres/100 or in km/litre).
Average consumption
This is the average fuel consumption since the computer was last set to zero.
It can be programmed and therefore displayed in mpg (litres/100 or in km/litre).
Distance travelled
This indicates the distance travelled since the computer was last set to zero.
Distance remaining to be travelled
This is the distance remaining to the final destination. It can either be cal-culated by the navigation if guidance is activated, or entered by the user, minus the distance covered since the distance was entered.
If the distance is not entered, dashes are displayed in place of the digits.
Average speed
This is the average speed calculated since the computer was last set to zero (with the ignition on).
This figure may change if there is a change in the style of driving or the road sur-face, producing a significant change in current consumption.
When the range is less than 20 miles (30 km), dashes are displayed. After filling with fuel, the range is displayed when it exceeds 62 miles (100 km).
If dashes are displayed for long peri-ods while driving instead of digits, contact a PEUGEOT dealer.

1
29
The routes "1" and ''2'' are independ-ent but have identical application.
Route "1" for example allows you to make daily calculations and route "2" monthly calculations.
Access via the general menu
"On-board computer" menu
Press the "MENU" button to gain access to the general menu.
Select the "On-board computer"icon, then confirm to gain access to its menu.Depending on the multi-function display, this menu offers dif-ferent options:
- Enter distance to destination,- Warning log,- Status of the functions.or
- On-board computer configuration,- Diagnostics,- Status of the functions.
Enter distance to destination
When guidance is not activated, this enables the driver to enter an approximate distance to final desti-nation value to permit all of the on-board computer calculations.
Warning log
This summarises the active warning messages by displaying them in suc-cession on the multifunction display.
Status of the functions
This summarises the active or inac-tive status of the functions present in the vehicle.
On-board computer configuration
This function enables the driver to enter the distance to the destination (when guidance is not activated; oth-erwise this information is given by the navigation system) and change the units of measurement (°C or °F, km and litres or miles and gallons).
The consumptions (current or aver-age) can be programmed and there-fore displayed in mpg (litres/100 or in km/litre).
Diagnostics
This presents the information relating to the warning log, the level of energy remaining in the back-up battery and the number of satellites which can be seen by the GPS.
The routes

2
30
MONOCHROME SCREEN A
(without RD4 audio equipment)
Presentation
This displays the following informa-tion:
- the time,- the date,- the outside temperature (this flashes if there is a risk of ice),- the status of the accesses (doors, boot, ...),- the warning messages (e.g.: "Antipollution system faulty") or information messages (e.g.: "Auto lights on"), displayed temporar-ily, can be cleared by pressing the "ESC" button,- the trip computer (see correspond-ing section).
Parameter configuration
There are three display control but-tons:
- "ESC" to abandon the operation in progress,- "MENU" to scroll through the menus or sub-menus,- "OK" to select the menu or sub-menu required.
General menu
Press the "MENU" button to scroll through the various menus of the general menu:
- vehicle configuration,- options,- display settings,- languages,- units.Press the "OK" button to select the menu required.

2
31
Vehicle configuration
Once the "Vehicle configuration" menu has been selected, you can activate or deactivate the following equipment:
- wiper linked with reverse gear,- "follow-me-home" lighting.
Languages
Once the "Languages" menu has been selected, you can change the lan-guage used by the display (Français, Italiano, Nederlands, Portugues, Portugues-Brasil, Deutsch, English, Espanol).
Display settings
Once the "Display settings" menu has been selected, you can gain access to the following settings:
- year,- month,- day,- hour,- minutes,- 12 or 24 hour mode.
Options
Once the "Options" menu has been selected, you can start diagnostics of the status of the equipment (active, not active, faulty).
Once you have selected a setting, press the "OK" button to change its value.
Wait for approximately ten sec-onds without any action to allow the changed data to be recorded or press the "ESC" button to cancel.
The display then returns to the nor-mal display.
Units
Once the "Units" menu has been selected, you can change the units of the following parameters:
- temperature (°C or °F),- fuel consumption (l/100, mpg or km/l).
For safety reasons, it is imperative that configuration of the multifunction displays by the driver takes place when stationary.

2
32
General menu
Press the "MENU" button to gain access to the general menu, then press the "" or "" buttons to scroll through the following items:
- radio-CD,- vehicle configuration,- options,- display settings,- languages,- units.Press the "OK" button to select the menu required.
Vehicle configuration
Once the "Vehicle configuration" menu has been selected, you can activate or deactivate the following equipment:
- rear wiper linked with reverse gear,- "follow-me-home" lighting.
Presentation
This displays the following informa-tion, via the RD4 audio equipment control keypad:
- the time,- the date,- the outside temperature (this flashes if there is a risk of ice),- the audio source displays (radio, CD, ...),- the status of the accesses (doors, boot, ...),- the warning messages (e.g.: "Antipollution system faulty") or information messages (e.g.: "Auto lights on"), displayed temporar-ily, can be cleared by pressing the "ESC" button,- the trip computer (see correspond-ing section).
MONOCHROME DISPLAY A
Options
Once the "Options" menu has been selected, you can start diagnostics of the status of the equipment (active, not active, faulty).
Radio-CD
With the RD4 audio equipment switched on, once the "Radio-CD" menu has been selected, you can activate or deactivate the functions linked with the use of the radio (RDS following, REG mode), the CD or the CD changer (introscan, random play, CD repeat).

2
33
Display settings
Once the "Display settings" menu has been selected, you can gain access to the following settings:
- year,- month,- day,- hour,- minutes,- 12 or 24 hour mode.
Languages
Once the "Languages" menu has been selected, you can change the lan-guage used by the display (Français, Italiano, Nederlands, Portugues, Portugues-Brasil, Deutsch, English, Espanol).
Units
Once the "Units" menu has been selected, you can change the units of the following parameters:
- temperature (°C or °F),- fuel consumption (l/100, mpg or km/l).
Once you have selected a setting, press the "" or "" buttons to change its value.
Press the "" or "" buttons to move to the previous or next setting respectively.
Press the "OK" button to record the change and return to the normal dis-play or press the "ESC" button to cancel.
For safety reasons, it is imperative that configuration of the multifunction displays by the driver takes place when stationary.