Peugeot 1007 Dag 2007 Manual PDF

Page 71 of 179

4
74
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system a few moments after the ignition has been switched off and therefore pre-vents starting of the vehicle by any-one who does not have the key.
The ignition key has an electronic chip which has a special code. When the ignition is switched on, the code is recognised and starting is possi-ble.
If the system does not function correctly, the service warning light comes on, accompanied by an audi-ble signal and a message on the mul-tifunction display.
In this case, your vehicle will not start.
Contact a PEUGEOT dealer as soon as possible.
Programming the remote control
Following changing of the remote control battery or disconnection of the vehicle battery, the remote con-trol must be reprogrammed.
 Wait at least one minute before using the remote control.
 Switch on the ignition.
 Press button B or C for at least five seconds within the next ten seconds.
 Switch off the ignition.
 Wait at least one minute before using the remote control.
The remote control is now working again.
Changing the remote control battery
Battery ref.: CR1620 / 3 volts.
The information "battery flat" is given by displaying of the service warning light, accompanied by an audible sig-nal and a message on the multifunc-tion display.
To replace the battery, unclip the cas-ing using a coin at the notch.
If the remote control does not work after the battery has been changed, re-programme the remote control.

Page 72 of 179

4
75
CONFIDENTIAL CARD
The confidential card contains the identification code necessary for any work carried out by a PEUGEOT dealer on the electronic immobiliser system. This code is hidden by a film, which should be removed only if nec-essary.
Keep your card in a safe place, never inside the vehicle.
Make a careful note of the number on each key. The key number is coded on the label attached to the key.
If the keys are lost, your PEUGEOT dealer can rapidly supply you with new keys.
The high frequency remote control is a sensitive system; do not oper-ate it while it is in your pocket as there is a possibility that it may unlock your vehicle, without you being aware of it.
The remote control does not oper-ate when the key is in the ignition, even when the ignition is switched off, except for reprogramming.
Do not operate the deadlocking function if there is anyone inside the vehicle.
Driving with the doors locked may make access to the passenger com-partment by the emergency serv-ices more difficult in an emergency.
As a safety precaution (with chil-dren on board), remove the ignition key when you leave the vehicle, even for a short time.
Do not repeatedly press the but-ton of your remote control out of range of your vehicle. You run the risk of stopping it from work-ing and the remote control would have to be reprogrammed.
When purchasing a second-hand vehicle:
- ensure that you are given the confidential card;- have the key codes memorised by a PEUGEOT dealer, to ensure that the keys in your possession are the only ones which can start the vehicle.
Do not make any modifications to the electronic engine immobiliser system.
Do not throw the remote con-trol batteries away, they con-tain metals which are harm-ful to the environment.
Take them to an approved collection point.

Page 73 of 179

4
76
ALARM
The alarm offers two types of protec-tion.
- external; the alarm sounds if one of the doors, the bonnet or the tailgate is opened,- internal; the alarm sounds if there is air movement in the passenger compartment (a broken window or movement within the car).
The alarm also has an anti-tamper function.
If there is an attempt to tamper with the following equipment:
- the wires to the siren or the control unit, the siren sounds accompanied by flashing of the direction indica-tors.- the battery, the siren sounds.
Complete setting and disarming of the alarm
Complete setting of the alarm
Switch off the ignition and get out of the vehicle.
Lock or deadlock the vehicle.
The direction indicators light for two seconds.
The red indicator light on the switch 1 flashes once a second.
5 seconds later, external protection is set.
45 seconds later, internal protection is set.
Note: when the alarm is triggered, the siren sounds for thirty seconds. However, after the siren stops, the alarm remains set.
Complete disarming of the alarm
Press the unlocking button on the remote control.
The direction indicators flash for two seconds.
The red indicator light on the switch 1 goes out.
Note: if the indicator light continues to flash after de-activation of the alarm, it is a sign that the alarm has been triggered during your absence. The flashing will stop when the igni-tion is switched on.
* According to country
When the alarm is set, if a door, the tailgate or the bon-net is not closed correctly, the siren sounds for a moment. If the vehicle is closed correctly in the following 45 seconds, the alarm is set. In all cases, the alarm is set after 45 seconds.
Automatic setting*
The alarm is set automatically 2 min-utes after the last door or the boot is closed.
To prevent the alarm being triggered when a door or the boot is opened, the remote control unlocking button must be pressed again.
Locking the vehicle without alarm
To lock the vehicle without activating the alarm (for example when wash-ing), insert the key in the lock, then lock it.

Page 74 of 179

4
77
Selection of the type of protection
To set the alarm to external protection only
If you want to leave a window par-tially open, or a pet inside the vehi-cle, you need to select external pro-tection only:
- switch off the ignition,- within the next ten seconds, press the control button 1 until the warn-ing light comes on continuously, - get out of the vehicle,- lock or deadlock the vehicle,- the direction indicators light for two seconds,- the red indicator light on the switch 1 flashes once a second.
Remote control failure
Unlock the doors using the key.
Open the door.
The alarm is triggered.
Switch on the ignition.
The electronic engine immobiliser system recognises the key.
The siren stops and the alarm is dis-armed.
Do not make any modifica-tions to the alarm system, this could result in malfunc-tions.
To de-activate external protection only
Press the unlocking button on the remote control.
The direction indicators flash for two seconds.
The red indicator light on the switch 1 goes out.
Work on the battery
The alarm must not be set when the battery is disconnected. Otherwise, the siren will sound.
After reconnecting the battery:
- lock or deadlock, then unlock the vehicle using the remote control,- the alarm will be operational again the next time the vehicle is locked or deadlocked.

Page 75 of 179

4
78
ELECTRIC WINDOWS
1. Driver's electric window switch.
2. Passenger electric window switch.
The electric window switches are not active when the door concerned is open.
The movement of a window stops if the door is opened. A second action on the electric window switch will only be taken into account when the door is closed.
Safety auto-reverse
In automatic mode, when the window rises and meets an obstacle, it stops and partially lowers again.
In the case of unwanted opening of the window on closing or if the window will not rise, lower it completely and raise it again immediately, by pulling the switch until the window closes completely. Continue to press the switch for approximately one sec-ond after closing.
The safety auto-reverse function is not operational during these operations.
Electric window
Press or pull switch 1. The window stops as soon as the switch is released.
One-touch electric window with safety auto-reverse
You have two options:
- Manual mode:
Press or pull switch 1 gently. The window stops as soon as the switch is released.
- Automatic mode:
Press or pull switch 1 fully. The win-dow opens or closes completely when the switch is released.
Pressing the switch again stops the movement of the window.
Note: the electrical functions of the one-touch electric windows are deac-tivated approximately one minute after the ignition is switched off.
Note: the electrical functions of the electric windows are deactivated approximately 45 seconds after the ignition is switched off, or when a door is opened.
Always remove the key from the ignition when leav-ing the vehicle, even for a short time.
In the event of contact when operating the windows, you must reverse the movement of the window. To do this, press the switch concerned.
When the driver operates the pas-senger window switches, he must ensure that no one is preventing cor-rect closing of the window.
The driver must ensure that passen-gers use the electric windows cor-rectly.
Be aware of children when operating the windows.

Page 76 of 179

4
79
THE "SESAME" DOORS
The exterior and interior handles only permit triggering of the electric movement of the door when it is fully closed or fully open.
Opening and closing of the doors is accompanied by an audible signal.
Closing from outside
Give a firm, fast push forwards on the handle, without guiding the door, to trigger the electric movement of the door.
Opening from outside
Using your hand, tilt the handle towards the rear of the vehicle and remove your hand from the handle when the electric movement of the door begins.
Locking / Unlocking from inside
Press button A, the red warning light comes on when the vehicle is locked and switches off when it is unlocked.
This locks/unlocks the doors and the tailgate.
If the vehicle is locked or deadlocked from outside, the red warning light flashes and button A does not func-tion. In this case, use the key or the remote control for unlocking.
Opening / Closing from inside
The opening and closing operates in the same way as from outside.
None of the door opening switches function when the vehicle is dead-locked.
To open using the inte-rior handle: tilt the handle, with the palm of your hand towards the door.

Page 77 of 179

4
80
Automatic central locking
The doors can lock automatically when you are driving (at a speed of more than 6 mph (10km/h).
You can activate or deactivate this function.
Driving with the doors locked may make access to the pas-senger compartment by the emergency services more difficult in an emergency.
Activation
With the ignition on, press and hold button A.
Activation of the function is accompa-nied by an audible signal and a mes-sage on the multifunction display.
Deactivation
With the ignition on, press and hold button A.
Deactivation of the function is accom-panied by an audible signal and a message on the multifunction dis-play.
"Door open" alert
- when the vehicle is moving, by lighting of the "door open" warning light, accompanied by an audible signal and a message on the multi-function display for a few seconds.
Opening / Closing using the remote control
Press button C or D to open or close the left or right door.
The opening and closing of the door is accompanied by an audible signal.
2nd press on button C or D during opening / closing interruption of the movement.
3rd press on button C or Dmove-ment of the door in the opposite direction.
You are advised to use the remote control or the con-trols as much as possible.
Opening / Closing from the front
Press switch B to open or close the corresponding door.
Choosing the movement of the door using the controls:
- pull opens the door,
- push closes,
- second press stops the move-ment,- the controls do not function above 3 mph (5 km/h).
If a door or the boot is not closed properly, you are warned:
- when the engine is running, by lighting of the "door open" warning light, accompanied by a message on the multifunction display for a few seconds.

Page 78 of 179

4
81
General recommendations
Always check that it is safe to oper-ate the door and be sure, in particu-lar, not to leave children or animals near the door controls without super-vision.
When opening the door, with the win-dow open, ensure that no person, animal or object is hanging through the window.
Before any opening or closing and during any movement of the doors, ensure that no person, animal or object is preventing the required manoeuvre, either inside or outside the vehicle.
It is imperative that the doors are operated only when the vehicle is stationary.
For your safety and for that of your passengers, as well as for cor-rect operation of the doors, you are strongly advised not to drive with a door open.
The audible warning, the lighting of the "door open" warning light and the message on the multifunction display are there to remind you.
Lock your vehicle when using an automatic carwash.
The doors and the overall dimensions of the vehicle
Safety / Obstacle detection
The obstacle detection system is triggered when an obstacle of a cer-tain physical resistance hinders the movement of the door.
• If an obstacle is detected while the door is closing, the door stops then opens fully.• If an obstacle is detected while the door is opening, the door stops. When you have removed the obsta-cle, complete or restart the action using buttons C or D on the remote control or the controls B.
When open, a door never protrudes beyond the rear bumper.
When open, a door exceeds the width of the exterior mirror by 8 mm, be sure to take this into account when you park alongside a wall, a post or a high kerb ...

Page 79 of 179

4
82
Behaviour in the case of a steep slope
It is possible to open and close the doors electrically up to a gradient of 20%.
In the case of a steep slope, the door may be driven by its own weight and as a conse-quence may open or close sharply.
Therefore:
• There would not be time for opera-tion of one of the electric controls to be taken into account.• There would not be time for the obstacle detection system to be triggered.Take care not to leave the vehicle on a steep slope with the door(s) open without supervision. If this advice is not followed, injuries or damage may occur if a part of the body or an object is trapped or caught.
In the event of an impact
The electric controls are deactivated in the event of an impact. Manual opening and closing is still possible.
Special features of operation
With the ignition off,
• doors open, power consuming equipment on (radio, lights…),or
• doors in an intermediate position (door neither fully open nor fully closed).After 30 minutes, the vehicle auto-matically switches to energy econ-omy mode.
However, if your vehicle is on a slope, with the front of the vehicle facing up, open the door with care. The door may open more quickly due to the incline of the ground.
However, if your vehicle is on a slope, with the front of the vehicle facing down, the door may not stay open and may close again sharply with the risk of injury.
Before any opening or clos-ing and during any move-ment of the doors, ensure that no person, animal or object is preventing the required manoeuvre, either inside or outside the vehicle. If this advice is not fol-lowed, injuries or damage may occur if a part of the body or an object is trapped or caught.
Electric closing and opening of the doors is not possible above 3 mph (5 km/h):
• If you set off with the door(s) open, you must slow down to below the threshold of 3 mph (5 km/h) in order to close the door(s).• Any attempt to open a door electri-cally using the interior handle, while driving, results in the door opening partially and, as a safety measure, locking in this position immediately. The audible warning, the lighting of the "door open" warning light and the message on the multifunction display accompany this situation. In order to release the door and be able to operate it again, you must slow down to below the threshold of 3 mph (5 km/h) again.

Page 80 of 179

4
83
TAILGATE
Simultaneous locking or unlocking of the tailgate and the doors
The tailgate is locked or unlocked by the remote control or from the driv-er's door lock.
To open, press the control 1 and lift the tailgate.
Tailgate release
This enables the tailgate to be unlocked in the event of a central locking fault.
- Fold back the rear seats to gain access to the lockfrom inside the boot,- Insert a small screwdriver into hole Aof the lock to unlock the tailgate.
"Tailgate open" warningIn this case, or following reconnection of the battery, with the doors open, it may be necessary to close the doors manually, in order to reinitialise them, and start the engine.
When the door has stopped in an intermediate position (neither fully open nor fully closed), only the remote control or the controls per-mit electric operation of the door.
When closing requests are made when the door is in a partially open position, the door may open slightly before closing.
When closing a door electrically when the battery is low, you are advised to guide the door manually. Recharge the battery as soon as possible.
If the electric controls (remote control or controls) no longer operate, reini-tialise the door(s) as follows:
1. Start the engine.
2. Manually open the door(s) fully.
3. Close the door(s) fully.
On completion of this procedure, electric operation of the doors is restored.
However, if a problem persists fol-lowing this procedure, contact a PEUGEOT dealer.
If the tailgate is not closed properly, you are warned:
- with the engine running, by light-ing of the "door open" warning light, accompanied by a message dis-played briefly on the multifunction display.- when the vehicle is moving, by lighting of the "door open" warning light, accompanied by an audible signal and a message displayed briefly on the multifunction display.
The tailgate locks automati-cally when the vehicle speed reaches 6 mph (10 km/h). It unlocks when one of the doors is opened if the speed is below 3 mph (5 km/h) or when the central locking button on the centre console is pressed.

Page:   < prev 1-10 ... 31-40 41-50 51-60 61-70 71-80 81-90 91-100 101-110 111-120 ... 180 next >