ignition Peugeot 1007 Dag 2008.5 Service Manual

9
126
Fuse N°RatingFunctions
120 AEngine control unit supply and fan assembly control - Engine control unit main relay - Injection control unit (Diesel) - Injection pump (Diesel) - Air heating solenoid valves (Diesel) - Air fl ow sensor (Diesel).
215 AHorn.
310 AFront and rear wash-wipe pump.
420 AHeadlamp wash pump.
515 AFuel pump (petrol).
610 APower steering control unit - Water in diesel sensor - Vehicle spe ed sensor.
710 ASwitching and protection unit (Diesel) - Engine coolant level detector (Diesel).
825 AStarter.
910 AABS/ESP control unit - ABS cut-off relay - Brake switch.
1030 A
Engine control unit actuators (petrol: ignition coils, oxygen se nsors, injectors, purge canister and variable timing solenoid valves, controlled thermosta t) (Diesel: injection control unit, air fl ow sensor, injection pump, diesel high pressure regulator, EGR and Turbo pressure regulation solenoid valves) - Blow-by heaters - Diesel heate r.
1140 AAir blowers.
1230 AWindscreen wipers (low/high speed).
1340 A(ignition positive) Built-In Systems Interface.
14-Not used.
1510 ARight main beam headlamp.
1610 ALeft main beam headlamp.
1715 ALeft dipped headlamp.
1815 ARight dipped headlamp.

9
127
CHANGING A WINDSCREEN WIPER BLADE
Changing a front wiper blade

 Lift the wiper arm.

 Unclip the blade and remove it.

 Fit the new blade.

 Push back the wiper arm.

Note: the shortest blade is fi tted on
the right-hand wiper arm.
Changing the rear wiper blade

 Lift the wiper arm.

 Unclip the blade and remove it.

 Fit the new blade.

 Push back the wiper arm.
ECONOMY MODE FUNCTION
After the engine has stopped, certain
functions (doors, windscreen wipers,
electric windows, courtesy light, audio
equipment, dipped headlamps, etc.)

can only be used for a cumulative
duration of thirty minutes, to prevent
discharging of the battery.
Once the thirty minutes are over, a
message informing you of the switch
to economy mode appears on the
multifunction display and the active
functions are put on standby.
These functions are reactivated
automatically next time the vehicle is
driven.
To resume the use of these functions
immediately, start the engine and let
it run for a few minutes.
The time available to you will then be
double the duration for which the en-
gine is left running. However, this pe-
riod will always be between fi ve and
thirty minutes.

Note: if the telephone is being used
when economy mode starts, it will
still be possible to fi nish the call.
A fl at battery will prevent the
engine from starting.
FITTING/REMOVING THE MAT
When removing the mat on the dri-
ver's side, push the seat as far back
as possible and remove the fi xings.
When refi tting, position the mat
correctly on the pins and clip the
fi xings. Check that the mat is secured
correctly.
To prevent the mat from becoming
caught under the pedals:
- only use mats suited to the fi xings already present in the
vehicle. It is imperative that these
fi xings are used.
- never fi t one mat on top of another.
Placing the wiper blades in the
special position


Less than a minute after switching
off the ignition, operate the wip-
ers stalk to position the wiper
blades in the centre of the wind-
screen.

To return the windscreen wipers
to their normal position, switch on
the ignition and operate the wipers
stalk.

9
128
BATTERY
The batteries contain harmful
substances such as sulphuric
acid and lead. They must be
disposed of in accordance
with regulations and must never be
discarded with household waste.
Take used remote control and vehi-
cle batteries to a special collection
point.
To start the vehicle from
another battery:
-
Connect the red cable to the positive
(+) terminals of the two batteries,
- Connect the green or black ca- ble to the negative (-) terminals
of the two batteries,
- Operate the starter, let the en- gine run,
- Wait for the engine to return to idle, then disconnect the cables.
Before disconnecting the
battery, you must wait for
2 minutes after switching off
the ignition.
Never disconnect a terminal when
the engine is running.
Never charge a battery without fi rst
disconnecting the terminals.
Close the windows, the sunroof and
the doors before disconnecting the
battery. If they do not operate nor-
mally following reconnection of the
battery, they must be reinitialised
(see sections "Sesame doors" and
"Sunroof"). After every reconnection of the bat-
tery:
- switch on the ignition and wait
1 minute before starting to al-
low the electronic systems to be
initialised. If slight diffi culties are
experienced after this, please
contact a PEUGEOT dealer.
-
reinitialise the "2 Tronic" gearbox
(refer to the corresponding section).

A. Flat battery

B. Slave battery
It is advisable to disconnect
the battery if the vehicle is
not to be used for a period
of more than one month.
To charge the battery using a
battery charger:
- Disconnect the battery,
- Follow the instructions for use
given by the battery charger
manufacturer,
- Reconnect starting with the nega- tive (-) terminal,
- Check that the terminals and connectors are clean. If they are
covered with sulphate (white or
greenish deposit), disconnect
them and clean them.