warning PEUGEOT 1007 DAG 2008 User Guide

Page 32 of 194

2
35
MONOCHROME DISPLAY C (without WIP Sound)
General menu
Press the "MENU" button to access
the general menu:
- trip computer (see corresponding section),
- personalisation-confi guration.
Turn the navigator to select the menu
required, then confi rm by pressing
the navigator.
Presentation
It displays the following information:
- the time,
- the date,
- the exterior temperature (this fl ashes if there is a risk of ice),
- the accesses check (doors, boot, ...),
- the warning messages (e.g.: "Antipollution system
faulty") or information messages
(e.g.: "Automatic headlamp
lighting activated"), displayed
temporarily, can be cleared by
pressing the "ESC" button,
- the trip computer (see corresponding section), Parameter configuration
There are three buttons and a navi-
gator to enable you to control the
screen:
-
"MENU" to display the general
menu,
- "MODE" to change the
permanent application (trip
computer, date,...),
- "ESC" to abandon the operation
in progress,
- Rotation of the navigator:
movement on the display or
changing of a setting,
- Press on the navigator:
confi rmation of the selection. "Personalisation-
Configuration" menu
Once this menu has been selected,
you can access the following func-
tions:
- defi ne the vehicle parameters,
- display confi guration,
- selection of the language.

Page 34 of 194

2
37
MONOCHROME SCREEN C
"Audio functions" menu
With the WIP Sound switched on,
once this menu has been selected,
you can activate or deactivate the
functions linked with the use of the
radio (RDS, REG, RadioText), the
CD or the CD changer (introscan,
random play, CD repeat).
Presentation
This displays the following infor-
mation, via the WIP Sound control
keypad:
- the time,
- the date,
- the outside temperature (this fl ashes if there is a risk of ice),
- the audio source displays (radio, CD, ...),
- the status of the accesses (doors, boot, ...),
- the warning messages (e.g.: "Antipollution system
faulty") or information messages
(e.g.: "Automatic headlamp
lighting activated"), displayed
temporarily, can be cleared by
pressing the "ESC" button,
- the trip computer (see corresponding section). General menu
Press the
"MENU" button to gain ac-
cess to the general menu:
- audio functions,
- trip computer (see corresponding section),
- personalisation-confi guration,
- telephone (hands-free kit).
Press the
"" or "" buttons to se-
lect the menu required, then confi rm
by pressing the "OK" button.
"Personalisation-
Configuration" menu
Once this menu has been selected,
you can gain access to the following
functions:
- defi ne the vehicle parameters,
- display confi guration,
- selection of the language.

Page 36 of 194

2
39
COLOUR SCREEN
Displays on the screen
When the ignition is switched on, this
displays the following information au-
tomatically and directly:
- the time,
- the date,
- the outside temperature (if there is a risk of ice, you are warned
by a message).
Warning messages (e.g.: "Fuel lev-
el low") and vehicle function status
messages (e.g.: "Automatic switch-
ing on of the headlamps activated")
may appear temporarily. These can
be cleared by pressing the "ESC"
button. General menu
When the WIP Com is switched on,
select the menu which corresponds
to the following applications:
- the satellite navigation system,
- the guidance on the map,
- the traffi c information,
- the audio sources (radio, CD,
Jukebox, ...),
- the telephone directories and functions,
- the confi guration of the screen and the setting of the
parameters of the vehicle's
equipment,
- the displaying of a video.
- the vehicle diagnostics (warnings log and status of the
functions). Controls
From the WIP Com control panel, to
select one of the applications:

 press the "MENU" button to
gain access to the general
menu ,

 turn the dial to move the
selection,

 press the dial to confi rm the
selection,
or

 press the "ESC" button to
abandon the operation in
progress and return to the
previous display.
For further details concerning these
applications, refer to the WIP Com
part of the "Audio and Telematics"
section.

Page 68 of 194

3
71
REAR INTERIOR LAYOUT
5. Retaining straps
These secure the warning triangle,
the tool kit, oil cans...
1. Rear parcel shelf
To remove the shelf:
- tilt and slightly raise the shelf,
- pull upwards on each side to de-
tach it from its fasteners.
There are several options for storing
the shelf:
- either behind the rear seats,
- or fl at in the boot.
2. Retaining hooks
3. Stowing rings
4. Luggage retaining net
Hooked onto the stowing rings, this
enables your luggage to be secured. 6. Storage trays in the fl oor
The right storage tray houses the
subwoofer of the JBL audio system.
7. Armrests/Side storage trays
These have recesses for storing a
can and a bottle.
8. Grab handles with coat hook

Page 71 of 194

4
74
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the
ignition is switched on, the code is
recognised and starting is possible.

If the system does not function
correctly, the service warning light
comes on, accompanied by an au-
dible signal and a message on the
multifunction display.
In this case, your vehicle will not
start. Contact a PEUGEOT dealer as
soon as possible.

Lost keys
Visit a PEUGEOT dealer with the ve-
hicle's V5 registration certifi cate and
your personal identifi cation docu-
ments.
A PEUGEOT dealer will be able to
retrieve the key code and the tran-
sponder code required to order a
replacement key.
Programming the remote
control
Following changing of the remote
control battery or disconnection of
the vehicle battery, the remote con-
trol must be reprogrammed.

 Wait at least one minute before
using the remote control.

 Switch on the ignition.

 Press button B or C for at least
fi ve seconds within the next ten
seconds.

 Switch off the ignition.

 Wait at least one minute before
using the remote control.
The remote control is now working
again.
Changing the remote control
battery
Battery ref.: CR1620/3 volts.
The information "battery fl at" is given
by displaying of the service warning
light, accompanied by an audible
signal and a message on the multi-
function display.
To replace the battery, unclip the casing
using a coin at the notch.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.

Page 73 of 194

4
74
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the
ignition is switched on, the code is
recognised and starting is possible.

If the system does not function
correctly, the service warning light
comes on, accompanied by an au-
dible signal and a message on the
multifunction display.
In this case, your vehicle will not
start. Contact a PEUGEOT dealer as
soon as possible.

Lost keys
Visit a PEUGEOT dealer with the ve-
hicle's V5 registration certifi cate and
your personal identifi cation docu-
ments.
A PEUGEOT dealer will be able to
retrieve the key code and the tran-
sponder code required to order a
replacement key.
Programming the remote
control
Following changing of the remote
control battery or disconnection of
the vehicle battery, the remote con-
trol must be reprogrammed.

 Wait at least one minute before
using the remote control.

 Switch on the ignition.

 Press button B or C for at least
fi ve seconds within the next ten
seconds.

 Switch off the ignition.

 Wait at least one minute before
using the remote control.
The remote control is now working
again.
Changing the remote control
battery
Battery ref.: CR1620/3 volts.
The information "battery fl at" is given
by displaying of the service warning
light, accompanied by an audible
signal and a message on the multi-
function display.
To replace the battery, unclip the casing
using a coin at the notch.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.

Page 76 of 194

4
77
Selection of the type
of protection Remote control failure
Unlock the doors using the key.
Open the door.
The alarm is triggered.
Switch on the ignition.
The electronic engine immobiliser
system recognises the key.
The siren stops and the alarm is
disarmed.
Do not make any modifi ca-
tions to the alarm system, this
could result in malfunctions.
To de-activate external protection
only
Press the unlocking button on the
remote control.
The direction indicators fl ash for
two seconds.
The red indicator light on the switch
1
goes out. Work on the battery
The alarm must not be set when the
battery is disconnected. Otherwise,
the siren will sound.
After reconnecting the battery:
- lock or deadlock, then unlock the
vehicle using the remote control,
- the alarm will be operational again the next time the vehicle is
locked or deadlocked.
To set the alarm to external
protection only
If you want to leave a window par-
tially open, or a pet inside the vehicle,
you need to select external protection
only:
- switch off the ignition,
- within the next ten seconds,
press the control button 1 until
the warning light comes on
continuously,
- get out of the vehicle,
- lock or deadlock the vehicle,
- the direction indicators light for two seconds,
- the red indicator light on the switch 1 fl ashes once a second.

Page 78 of 194

4
79
"SESAME" DOORS
The exterior and interior handles
only permit triggering of the electric
movement of the door when it is fully
closed or fully open.
Opening and closing of the doors is
accompanied by an audible signal.
Closing from outside
Give a fi rm, fast push forwards on the
handle, without guiding the door, to
trigger the electric movement of the
door.
Opening from outside
Using your hand, tilt the handle to-
wards the rear of the vehicle and
remove your hand from the handle
when the electric movement of the
door begins.
Locking/Unlocking from inside
Press button
A , the red warning light
comes on when the vehicle is locked
and switches off when it is unlocked.
This locks/unlocks the doors and the
tailgate.
If the vehicle is locked or deadlocked
from outside, the red warning light
fl ashes and button A does not func-
tion. In this case, use the key or the
remote control for unlocking.
Opening/Closing from inside
The opening and closing operates in
the same way as from outside.
None of the door opening switches
function when the vehicle is dead-
locked.
To open using the interior
handle: tilt the handle, with
the palm of your hand to-
wards the door.

Page 79 of 194

4
80
Automatic central locking
The doors can lock automatically
when you are driving (at a speed of
more than 6 mph (10 km/h).
You can activate or deactivate this
function. Driving with the doors locked
may make access to the pas-
senger compartment by the
emergency services more
diffi cult in an emergency.
Activation
With the ignition on, press and hold
button A .
Activation of the function is accompa-
nied by an audible signal and a mes-
sage on the multifunction display.
Deactivation
With the ignition on, press and hold
button A .
Deactivation of the function is
accompanied by an audible signal
and a message on the multifunction
display.
"Door open" alert -
when the vehicle is moving,
by lighting of the "door open"
warning light, accompanied by
an audible signal and a message
on the multifunction display for a
few seconds.
Opening/Closing using the
remote control
Press button C or D to open or close
the left or right door.
The opening and closing of the door is
accompanied by an audible signal.
2nd press on button C or D during
opening/closing  interruption of the
movement.
3rd press on button C or D  move-
ment of the door in the opposite
direction.
You are advised to use the
remote control or the controls
as much as possible.
Opening/Closing from the front
Press switch
B to open or close the
corresponding door.
Choosing the movement of the door
using the controls:
- pull  opens the door,
- push  closes,
- second press  stops the
movement,
- the controls do not function above 3 mph (5 km/h).
If a door or the boot is not
closed properly, you are
warned:
- when the engine is running,
by lighting of the "door open"
warning light, accompanied by
a message on the multifunction
display for a few seconds.

Page 80 of 194

4
81
General
recommendations
Always check that it is safe to operate
the door and be sure, in particular, not
to leave children or animals near the
door controls without supervision.
When opening the door, with the win-
dow open, ensure that no person,
animal or object is hanging through
the window.
Before any opening or closing and
during any movement of the doors,
ensure that no person, animal or ob-
ject is preventing the required ma-
noeuvre, either inside or outside the
vehicle.
It is imperative that the doors are
operated only when the vehicle is
stationary.
For your safety and for that of your pas-
sengers, as well as for correct operation
of the doors, you are strongly advised
not to drive with a door open. The au-
dible warning, the lighting of the "door
open" warning light and the message
on the multifunction display are there to
remind you.
Lock your vehicle when using an au-
tomatic carwash. The doors and the overall
dimensions of the vehicle
Safety/Obstacle detection
The obstacle detection system is
triggered when an obstacle of a cer-
tain physical resistance hinders the
movement of the door.


Page:   < prev 1-10 11-20 21-30 31-40 41-50 50 next >