PEUGEOT 107 2006 Owner's Manual

2AUDIO EQUIPMENT
23
GENERAL FUNCTIONSOn / off
With the ignition key in
the accessories posi-
tion or with the igni-
tion on, press this button to switch
the audio equipment on or off.
After the engine has been switched
off, the audio equipment can only
operate for approximately 30 min-
utes, to prevent discharging of the
battery. Press the upper part
of this button several
times in succession to
increase the volume
of the audio equip-
ment or the lower
part of this button to
decrease it.
VOLUME ADJUSTMENT
CLOCK ADJUSTMENT
Press this button sev-
eral times in succes-
sion to gain access
to the bass (BASS),
treble (TREB) , front / rear balance
(FAD) and left / right balance (BAL)
settings.
AUDIO SETTINGS
Press this button for
more than 2 seconds,
the clock display
flashes:
AUXILIARY SOCKET
An auxiliary socket
"AUX" is provided for
the connection of port-
able equipment (MP3
player, etc.).
When the parameter
is displayed, change
the setting using these
two buttons.
You exit from this mode automati-
cally after a few seconds without any
action. In order to listen to it,
connect your equip-
ment then press this
button.
The audio equipment controls ena-
ble you to adjust the volume and the
audio settings.
To exit from the AUX source, press
AM/FM .
- to adjust the hours, press this button,
- to adjust the min- utes, press this but-
ton. Note:
set the volume of the
portable equipment to half
volume to avoid saturating
the audio equipment sound.
Then use the audio equipment vol-
ume button.
You exit from this mode automati-
cally after a few seconds without any
action.

2AUDIO EQUIPMENT
24
Selection of the AM / FM
(FM1, FM2, FM3) wavebands Autostore: automatic storing of
6 stations on AM and FM3 TA function on/off: traffic
information priority
Automatic search for a higher frequency: double press / Successive tuning in to the stations Selection of the type of radio
programme: News, Sports, Talk, Pop, Classics AF function on/off:
alternative frequency
Manual search for
a higher frequency
Selection of the stored station / Storing of a station: press for more than 2 seconds Manual search for
a lower frequency
RADIO

2AUDIO EQUIPMENT
25
Stereo reception
When the audio equipment receives
a station broadcasting in stereo it
automatically transmits stereo sound
and the screen displays "ST". If the
reception conditions deteriorate, the
audio equipment returns to mono
transmission and "ST" is no longer
displayed. Press one of these
two buttons briefly to
increase or decrease
the frequency dis-
played respectively.
If you maintain the
pressure on the button
in the chosen direc-
tion, the frequency will be scanned
continuously.
The scan stops when you release the
button.
Manual station search
Automatic station search
Manual station storing
Selection of the radio source
Selection of a waveband
Press this button. Press this button twice
to select the next sta-
tion.
Press this button
briefly to listen to each station avail-
able on the FM waveband for three
seconds. To stop the station scan,
press this button again.
If the traffic information programme
TA is selected, only stations which
broadcast this type of programme
are selected.
Press the button
several times in suc-
cession to select the
wavebands FM1,
FM2, FM3 and AM. Select the required station.
Press one of the buttons "1" to "6"
for more than 2 seconds
An audible signal confirms that the
station has been stored.

2AUDIO EQUIPMENT
26
Notes on radio
reception
Your audio equipment will
be subjected to phenomena
which do not affect domestic radio
sets. Both MW/LW and FM reception
are subject to various forms of inter-
ference. This is no reflection on the
quality of the equipment but is due to
the nature of the signals and the way
in which they are transmitted.
On MW/LW, interference may be
noticed when passing under high
voltage power lines or bridges, or in
tunnels.
On FM, interference may be the
result of increasing distance from the
transmitter, deflection of the signal
by obstacles (mountains, hills, build-
ings, etc) or of being in an area which
is not covered by a transmitter.
Automatic storing of FM
stations (autostore)
Press this button.
Your audio equipment
automatically stores
the six best transmit-
ters received on AM and FM in your
current location. These stations are
stored on the AM and FM3 wave-
bands. The end of the search is sig-
nalled by two audible signals.
Recalling stored stations
On each waveband, a brief press on
one of the buttons "1" to "6" recalls
the corresponding stored station.
If it was not possible to find
six transmitters, the remain-
ing memories remain empty:
three dashes are displayed
on the audio equipment screen for
each empty memory.

2AUDIO EQUIPMENT
27
RDS
Using the AF (alternative
frequency) function on the FM
waveband
Regional following
mode (REG)
This enables you to listen to sta-
tions which broadcast a type of pro-
gramme which has a theme (NEWS,
SPORTS, TALK, POP, CLASSICS).
Search by type of
programme (PTY)EON system
This system links stations which
belong to the same network. It per-
mits the transmission of traffic infor-
mation broadcast by a station which
belongs to the same network as the
station to which you are listening.
In order to benefit from this, select the
traffic information programme
TA.
The
RDS (Radio Data System) ena-
bles you to continue listening to the
same station irrespective of the fre-
quency that it uses in your current
location. The audio equipment con-
tinuously searches for the transmitter
which provides the best reception.
Some stations, organised in a
network, broadcast regional pro-
grammes in the various regions
which they serve. The regional fol-
lowing mode enables you to contiue
listening to the same programme.
Press this button sev-
eral times in succes-
sion to activate or deac-
tivate the function.
On FM, the multifunction display will
indicate:
- "TP" or "TP EON" : the radio trans-
mits a programme while awaiting
the broadcasting of traffic informa-
tion.
- "TA" or "TA EON" : the programme
transmitted by the radio is put on
standby while awaiting the broad-
casting of traffic information.
If you wish to interrupt the transmis-
sion of a message, press this button
again.
Traffic information
programme (TA)
Press this button
several times in suc-
cession to activate or
deactivate the func-
tion.
The screen will indicate:
- "AF" if the function is activated,
- "AF REG" if the function is acti-
vated at regional level,
- "AF" flashing if the function is not
available. When
FM is selected,
press this button:
- "no pty" is displayed,
- then press the button briefly to select a programme.
After a few seconds without any
action, your selection is stored. Notes:
the volume of the traf-
fic information is independ-
ent of the volume of normal
radio listening.
You can adjust it using the
volume button, when the TA pro-
gramme is being transmitted.
The setting will be stored and will be
used during subsequent message
transmissions.

2AUDIO EQUIPMENT
28
CD ejectSelection of the source:
CD or CD changer or auxiliary Selection of the next track
Playing of the start of each
track on the CD: brief press 
: accelerated forwards play
 : accelerated backwards play Selection of the previous track
Random playing of the tracks on the CD currently being played
CD changer:
 : selection of the previous CD
 : selection of the next CD CD: repeating of the current track /
CD changer, press for more than 2 seconds: repeating of the current CD
CD PLAYER OR CD CHANGER

2AUDIO EQUIPMENT
29
Press this button to
select the next track.
Press this button to
return to the start of
the current track or
to select the previous
track.
CD PLAYER AND CD
CHANGER FUNCTIONS
Selection of a track on a CD
Introscan (SCAN)
Press this button to
listen to the start of
each track on the cur-
rent CD.
Accelerated play
Press and hold one
of these buttons for
accelerated forwards
or backwards play
respectively.
The accelerated play
stops when the button
is released.When a CD is inserted,
printed face upper-
most, play begins
automatically.
If there is a CD in the player already,
press this button.
CD PLAYER FUNCTIONS
Selection of the CD player Repeating of a track on the
CD (RPT)
Random playing of the CD
(RAND)
When the CD player
is selected, press this
button. If you wish to listen
to the current track
again, press this but-
ton. To cancel the rep-
etition, press the button again.
CD eject
Press this button to
eject the CD from the
player.
The tracks on the CD will be played
in a random order. Press the button
again to return to normal play.
The random play mode is deacti-
vated when the audio equipment is
switched off. The use of copied CDs may
cause faults.
Insert circular CDs only.

2AUDIO EQUIPMENT
28
CD ejectSelection of the source:
CD or CD changer or auxiliary Selection of the next track
Playing of the start of each
track on the CD: brief press 
: accelerated forwards play
 : accelerated backwards play Selection of the previous track
Random playing of the tracks on the CD currently being played
CD changer:
 : selection of the previous CD
 : selection of the next CD CD: repeating of the current track /
CD changer, press for more than 2 seconds: repeating of the current CD
CD PLAYER OR CD CHANGER

2AUDIO EQUIPMENT
29
Press this button to
select the next track.
Press this button to
return to the start of
the current track or
to select the previous
track.
CD PLAYER AND CD
CHANGER FUNCTIONS
Selection of a track on a CD
Introscan (SCAN)
Press this button to
listen to the start of
each track on the cur-
rent CD.
Accelerated play
Press and hold one
of these buttons for
accelerated forwards
or backwards play
respectively.
The accelerated play
stops when the button
is released.When a CD is inserted,
printed face upper-
most, play begins
automatically.
If there is a CD in the player already,
press this button.
CD PLAYER FUNCTIONS
Selection of the CD player Repeating of a track on the
CD (RPT)
Random playing of the CD
(RAND)
When the CD player
is selected, press this
button. If you wish to listen
to the current track
again, press this but-
ton. To cancel the rep-
etition, press the button again.
CD eject
Press this button to
eject the CD from the
player.
The tracks on the CD will be played
in a random order. Press the button
again to return to normal play.
The random play mode is deacti-
vated when the audio equipment is
switched off. The use of copied CDs may
cause faults.
Insert circular CDs only.

2AUDIO EQUIPMENT
30
Press this button.
CD CHANGER FUNCTIONS
Selection of the CD changerRandom playing of a CD
(RAND)
When the CD changer
is selected, press this
button for 2 seconds.
The tracks of the
current CD will be played in a random
order.
Press the button again for 2 seconds
to return to normal play.
Selection of a CD
Press one of these
buttons on the audio
equipment to select
the previous or next
CD respectively.
Repeating of a CD (RPT)
If you wish to listen to
the current CD again,
press and hold this
button.
The use of copied CDs may
cause faults.
Insert circular CDs only.
To cancel the repetition, press the
button again.