PEUGEOT 107 2008 Owner's Manual

2
23
AUDIO EQUIPMENT
GENERAL FUNCTIONS
On/off
With the ignition key
in the accessories po-
sition or with the ignition on, press
this button to switch the audio equi-
pment on or off.

After the engine has been swit-
ched off, the audio equipment can
only operate for approximately
30 minutes, to prevent dischar-
ging of the battery. Press the upper part
of this button several
times in succession to
increase the volume
of the audio equip-
ment or the lower part
of this button to de-
crease it.
VOLUME ADJUSTMENT
CLOCK ADJUSTMENT
Press this button seve-
ral times in succession
to gain access to the
bass (BASS) , treble

(TREB) , front/rear balance (FAD) and
left/right balance (BAL) settings.
AUDIO SETTINGS
Press this button for
more than 2 seconds,
the clock display
fl ashes:
AUXILIARY SOCKET
An auxiliary socket

"AUX" is provided for
the connection of por-
table equipment (MP3
player, etc.).
When the parameter
is displayed, change
the setting using the-
se two buttons.
You exit from this mode automati-
cally after a few seconds without any
action. In order to listen to it,
connect your equip-
ment then press this
button.
The audio equipment controls ena-
ble you to adjust the volume and the
audio settings.
To exit from the AUX source, press

AM/FM .

When using an MP3 player: increase
the volume of the radio signifi cantly
(between 30 and 60) to obtain a satis-
factory playing volume.
- to adjust the hours, press this button,
-
to adjust the minutes,
press this button.
You exit from this mode automati-
cally after a few seconds without any
action.

2
24
AUDIO EQUIPMENT Selection of the AM/FM
(FM1, FM2, FM3) wavebands Autostore: automatic storing of
6 stations on AM and FM3 TA function on/off: traffi c
information priority
Automatic search for a higher frequency: double press/
Successive tuning in to the stations Selection of the type of radio
programme: News, Sports, Talk, Pop, Classics AF function on/off: alternative
frequency
Manual search for a higher frequency
Selection of the stored station/ Storing of a station: press for more than 2 seconds Manual search for a lower
frequency
RADIO

2
25
AUDIO EQUIPMENT
Stereo reception
When the audio equipment receives
a station broadcasting in stereo it
automatically transmits stereo sound
and the screen displays "ST" . If the
reception conditions deteriorate, the
audio equipment returns to mono
transmission and "ST" is no longer
displayed. Press one of these
two buttons briefl y to
increase or decrease
the frequency dis-
played respectively.
If you maintain the
pressure on the button
in the chosen direc-
tion, the frequency will be scanned
continuously.
The scan stops when you release the
button.
Manual station search
Automatic station search
Manual station storing
Selection of the radio source
Selection of a waveband
Press this button. Press this button twi-
ce to select the next
station.
Press this button brie-
fl y to listen to each station availa-
ble on the FM waveband for three
seconds. To stop the station scan,
press this button again.
If the traffi c information programme

TA is selected, only stations which
broadcast this type of programme
are selected.
Press the button seve-
ral times in succession
to select the wave-
bands FM1, FM2, FM3
and AM. Select the required station.
Press one of the buttons "1" to "6"
for more than 2 seconds
An audible signal confi rms that the
station has been stored.

2
26
AUDIO EQUIPMENT Notes on radio
reception
Your audio equipment will be
subjected to phenomena which do
not affect domestic radio sets. Both
MW/LW and FM reception are sub-
ject to various forms of interference.
This is no refl ection on the quality of
the equipment but is due to the natu-
re of the signals and the way in which
they are transmitted.
On MW/LW, interference may be noti-
ced when passing under high voltage
power lines or bridges, or in tunnels.
On FM, interference may be the re-
sult of increasing distance from the
transmitter, defl ection of the signal by
obstacles (mountains, hills, buildings,
etc) or of being in an area which is
not covered by a transmitter.
Automatic storing of FM
stations (autostore)
Press this button.
Your audio equipment
automatically stores
the six best transmit-
ters received on AM and FM in your
current location. These stations are
stored on the AM and FM3 wave-
bands. The end of the search is si-
gnalled by two audible signals. Recalling stored stations
On each waveband, a brief press on
one of the buttons
"1" to "6" recalls
the corresponding stored station.
If it was not possible to fi nd
six transmitters, the re-
maining memories remain
empty: three dashes are
displayed on the audio equipment
screen for each empty memory.

2
27
AUDIO EQUIPMENT
Regional following mode
(REG)
Some stations, organised in a
network, broadcast regional pro-
grammes in the various regions
which they serve. The regional fol-
lowing mode enables you to continue
listening to the same programme. Search by type of programme
(PTY)
This enables you to listen to sta-
tions which broadcast a type of pro-
gramme which has a theme (NEWS,
SPORTS, TALK, POP, CLASSICS).
EON system
This system links stations which be-
long to the same network. It permits
the transmission of traffi c information
broadcast by a station which belongs
to the same network as the station to
which you are listening.
In order to benefi t from this, select the
traffi c information programme
TA .
Using the AF (alternative
frequency) function on the FM
waveband
The
RDS (Radio Data System) ena-
bles you to continue listening to the
same station irrespective of the fre-
quency that it uses in your current
location. The audio equipment conti-
nuously searches for the transmitter
which provides the best reception.
Press this button seve-
ral times in succession
to activate or deacti-
vate the function.
On FM, the multifunction display will
indicate:
- "TP" or "TP EON" : the radio
transmits a programme while
awaiting the broadcasting of
traffi c information.
-
"TA" or "TA EON" : the programme
transmitted by the radio is put
on standby while awaiting the
broadcasting of traffi c information.

If you wish to interrupt the transmis-
sion of a message, press this button
again.
Traffic information
programme (TA)
Press this button seve-
ral times in succession
to activate or deacti-
vate the function.
The screen will indicate:
- "AF" if the function is activated,
- "AF REG" if the function is
activated at regional level,
- "AF" fl ashing if the function is not
available. When
FM is selected,
press this button:

Notes: the volume of the
traffi c information is indepen-
dent of the volume of normal
radio listening.
You can adjust it using the volume
button, when the TA programme is
being transmitted.
The setting will be stored and will be
used during subsequent message
transmissions.
RDS
- "no pty" is displayed,
- then press the button briefl y to select a programme.
After a few seconds without any action,
your selection is stored.

2
28
AUDIO EQUIPMENT CD eject Selection of the source: CD or CD
changer or auxiliary Selection of the next track
Playing of the start of each track on the CD: brief press
 : accelerated forwards play

 : accelerated backwards play Selection of the previous track
Random playing of the tracks on the CD currently being played
CD changer:

 : selection of the previous CD

 : selection of the next CD CD: repeating of the current track/CD changer, press
for more than 2 seconds: repeating of the current CD
CD PLAYER OR CD CHANGER

2
29
AUDIO EQUIPMENT
Press this button to
select the next track.
CD PLAYER AND CD
CHANGER FUNCTIONS
Introscan (SCAN) Press this button to
listen to the start of
each track on the cur-
rent CD.
Accelerated play
Press and hold one of
these buttons for ac-
celerated forwards or
backwards play res-
pectively.
The accelerated play
stops when the button
is released. When a CD is inser-
ted, printed face up-
permost, play begins
automatically.
If there is a CD in the player already,
press this button.
CD PLAYER FUNCTIONS Repeating of a track on the
CD (RPT)
Random playing of the CD
(RAND) When the CD player
is selected, press this
button. If you wish to listen to
the current track again,
press this button. To
cancel the repetition,
press the button again.
CD eject Press this button to
eject the CD from the
player.
The tracks on the CD will be played
in a random order. Press the button
again to return to normal play.
The random play mode is deacti-
vated when the audio equipment is
switched off. The use of copied CDs may
cause faults.
Insert circular CDs only.
Selection of a track on a CD
Press this button to re-
turn to the start of the
current track or to se-
lect the previous track. Selection of the CD player

2
28
AUDIO EQUIPMENT CD eject Selection of the source: CD or CD
changer or auxiliary Selection of the next track
Playing of the start of each track on the CD: brief press
 : accelerated forwards play

 : accelerated backwards play Selection of the previous track
Random playing of the tracks on the CD currently being played
CD changer:

 : selection of the previous CD

 : selection of the next CD CD: repeating of the current track/CD changer, press
for more than 2 seconds: repeating of the current CD
CD PLAYER OR CD CHANGER

2
29
AUDIO EQUIPMENT
Press this button to
select the next track.
CD PLAYER AND CD
CHANGER FUNCTIONS
Introscan (SCAN) Press this button to
listen to the start of
each track on the cur-
rent CD.
Accelerated play
Press and hold one of
these buttons for ac-
celerated forwards or
backwards play res-
pectively.
The accelerated play
stops when the button
is released. When a CD is inser-
ted, printed face up-
permost, play begins
automatically.
If there is a CD in the player already,
press this button.
CD PLAYER FUNCTIONS Repeating of a track on the
CD (RPT)
Random playing of the CD
(RAND) When the CD player
is selected, press this
button. If you wish to listen to
the current track again,
press this button. To
cancel the repetition,
press the button again.
CD eject Press this button to
eject the CD from the
player.
The tracks on the CD will be played
in a random order. Press the button
again to return to normal play.
The random play mode is deacti-
vated when the audio equipment is
switched off. The use of copied CDs may
cause faults.
Insert circular CDs only.
Selection of a track on a CD
Press this button to re-
turn to the start of the
current track or to se-
lect the previous track. Selection of the CD player

2
30
AUDIO EQUIPMENT Press this button.
CD CHANGER FUNCTIONS Random playing of a CD
(RAND) When the CD changer
is selected, press this
button for 2 seconds.
The tracks of the current CD will be
played in a random order.
Press the button again for 2 seconds
to return to normal play.
Selection of a CD Press one of these
buttons on the audio
equipment to select
the previous or next
CD respectively. Repeating of a CD (RPT)
If you wish to listen to
the current CD again,
press and hold this
button.
The use of copied CDs may
cause faults.
Insert circular CDs only.
To cancel the repetition, press the
button again.
Selection of the CD changer