bulb PEUGEOT 107 2008 Owners Manual

9
71
PRACTICAL INFORMATION
CHANGING A BULB
1. Side lights (W 5 W)

 Turn the bulb holder A one quarter
of a turn and remove it.

 Remove the bulb and change it.
2. Direction indicators (PY 21 W amber)

 Turn the bulb holder B one quarter
of a turn and remove it.

 Turn the bulb one quarter of a turn.

 Remove the bulb and change it.
If you encounter any diffi culties,
contact a PEUGEOT dealer.

Note: in certain climatic con-
ditions (low temperatures,
humidity), the presence of
condensation on the in-
ternal face of the headlamps is
normal ; it disappears a few minutes
after the lights are switched on.
Never go underneath a vehi-
cle supported only by a jack
(use an axle stand).

4. Fold the jack 2 and detach it.

5. Tighten the wheel bolts using the
wheelbrace 1 .

6. Refi t the trim.

7. Store the tools and the wheel in
the boot.
The jack and the tool kit are specifi c
to your vehicle. Do not use them for
other purposes.
After changing a wheel:
- have the tightening of the bolts and the pressure of the spare wheel
checked as soon as possible,
- have the punctured wheel re-paired and refi t it on the vehicle
as soon as possible.
Consult a PEUGEOT dealer. Front lights

1. Side lights

2. Direction indicators

3. Dipped headlamps/Main beam
headlamps

9
71
PRACTICAL INFORMATION
CHANGING A BULB
1. Side lights (W 5 W)

 Turn the bulb holder A one quarter
of a turn and remove it.

 Remove the bulb and change it.
2. Direction indicators (PY 21 W amber)

 Turn the bulb holder B one quarter
of a turn and remove it.

 Turn the bulb one quarter of a turn.

 Remove the bulb and change it.
If you encounter any diffi culties,
contact a PEUGEOT dealer.

Note: in certain climatic con-
ditions (low temperatures,
humidity), the presence of
condensation on the in-
ternal face of the headlamps is
normal ; it disappears a few minutes
after the lights are switched on.
Never go underneath a vehi-
cle supported only by a jack
(use an axle stand).

4. Fold the jack 2 and detach it.

5. Tighten the wheel bolts using the
wheelbrace 1 .

6. Refi t the trim.

7. Store the tools and the wheel in
the boot.
The jack and the tool kit are specifi c
to your vehicle. Do not use them for
other purposes.
After changing a wheel:
- have the tightening of the bolts and the pressure of the spare wheel
checked as soon as possible,
- have the punctured wheel re-paired and refi t it on the vehicle
as soon as possible.
Consult a PEUGEOT dealer. Front lights

1. Side lights

2. Direction indicators

3. Dipped headlamps/Main beam
headlamps

9
73
PRACTICAL INFORMATION Third brake light
(Four W 5 W bulbs)

 Unscrew the 2 fi xing bolts A .

 Release the lamp unit by pushing
the two tabs B inwards.

 Disconnect the connector and the
rear wash-wipe pipe.

 Remove the bulb holder.

 Remove the bulb and change it.
When refi tting, proceed in the reverse
order and ensure that the lamp unit
seal and the rear wash-wipe pipe have
been put back in place correctly.
Do not tighten the bolts more
than is necessary at the risk
of breaking the light.
Number plate lights (W 5 W)

 Pass your hand under the bumper.

 Remove the bulb holder turning it
one quarter of a turn.

 Remove the bulb and change it.

 unclip the harness,

 remove the bulb holder moving
aside the four tabs B ,

 remove the bulb and change it.

Note: when refi tting, proceed in the
reverse order and take care to posi-
tion the bulb holder, the tabs and the
light correctly.