PEUGEOT 107 2009 Owner's Manual

2
23
AUDIO EQUIPMENT
GENERAL FUNCTIONS
On/off
With the ignition key
in the accessories po-
sition or with the ignition on, press
this button to switch the audio equip-
ment on or off.

After the engine has been switched
off, the audio equipment can
only operate for approximately
30 minutes, to prevent discharging
of the battery. Press the upper part
of this button several
times in succession to
increase the volume
of the audio equip-
ment or the lower part
of this button to de-
crease it.
VOLUME ADJUSTMENT
CLOCK ADJUSTMENT
Press this button sever-
al times in succession to
gain access to the bass

(BASS) , treble (TREB) ,
front/rear balance (FAD) and left/right
balance (BAL) settings.
AUDIO SETTINGS
Press this button for more
than 2 seconds, the clock
display fl ashes:
AUXILIARY SOCKET
An auxiliary socket

"AUX" is provided
for the connection of
portable equipment
(MP3 player, etc.).
When the parameter
is displayed, change
the setting using these
two buttons.
You exit from this mode automati-
cally after a few seconds without any
action. In order to listen to it,
connect your equip-
ment then press this
button.
The audio equipment controls enable
you to adjust the volume and the audio
settings.
To exit from the AUX source, press

AM/FM .

When using an MP3 player: in-
crease the volume of the radio signifi -
cantly (between 30 and 60) to obtain
a satisfactory playing volume.
- to adjust the hours, press this button,
- to adjust the minutes, press this button.
You exit from this mode automati-
cally after a few seconds without any
action.

2
24
AUDIO EQUIPMENT Selection of the AM/FM
(FM1, FM2, FM3) wavebands Autostore: automatic storing of
6 stations on AM and FM3 TA function on/off: traffi c
information priority
Automatic search for a higher frequency: double press/Successive tuning in to the stations Selection of the type of radio
programme: News, Sports, Talk, Pop, Classics AF function on/off:
alternative frequency
Manual search for a higher frequency
Selection of the stored station/ Storing of a station: press for more than 2 seconds Manual search for a lower
frequency
RADIO

2
25
AUDIO EQUIPMENT
Stereo reception
When the audio equipment receives
a station broadcasting in stereo it au-
tomatically transmits stereo sound
and the screen displays "ST" . If the
reception conditions deteriorate, the
audio equipment returns to mono
transmission and "ST" is no longer
displayed. Press one of these
two buttons briefl y to
increase or decrease
the frequency dis-
played respectively.
If you maintain the
pressure on the button
in the chosen direction,
the frequency will be
scanned continuously.
The scan stops when you release the
button.
Manual station search
Automatic station search
Manual station storing
Selection of the radio source
Selection of a waveband
Press this button. Press this button twice
to select the next
station.
Press this button briefl y to listen to
each station available on the FM
waveband for three seconds. To stop
the station scan, press this button
again.
If the traffi c information programme

TA is selected, only stations which
broadcast this type of programme
are selected.
Press the button suc-
cessively to select
the wavebands FM1,
FM2, FM3 and AM. Select the required station.
Press one of the buttons "1" to "6"
for more than 2 seconds
An audible signal confi rms that the
station has been stored.

2
26
AUDIO EQUIPMENT Notes on radio reception
Your audio equipment will
be subjected to phenomena
which do not affect domestic radio
sets. Both MW/LW and FM reception
are subject to various forms of inter-
ference. This is no refl ection on the
quality of the equipment but is due to
the nature of the signals and the way
in which they are transmitted.
On MW/LW, interference may be no-
ticed when passing under high voltage
power lines or bridges, or in tunnels.
On FM, interference may be the re-
sult of increasing distance from the
transmitter, defl ection of the signal by
obstacles (mountains, hills, buildings,
etc) or of being in an area which is not
covered by a transmitter.
Automatic storing of FM
stations (autostore)
Press this button.
Your audio equipment
automatically stores
the six best transmit-
ters received on AM and FM in your
current location. These stations are
stored on the AM and FM3 wave-
bands. The end of the search is sign-
alled by two audible signals. Recalling stored stations
On each waveband, a brief press on
one of the buttons
"1" to "6" recalls
the corresponding stored station.
If it was not possible to fi nd
six transmitters, the remain-
ing memories remain empty:
three dashes are displayed
on the audio equipment screen for
each empty memory.

2
27
AUDIO EQUIPMENT
Regional mode (REG)
Some stations, organised in a net-
work, broadcast regional programmes
in the various regions which they
serve. The regional mode enables
you to continue listening to the same
programme. Search by type of programme
(PTY)
This enables you to listen to stations
which broadcast a type of programme
which has a theme (NEWS, SPORTS,
TALK, POP, CLASSICS).
EON system
This system links stations which be-
long to the same network. It permits
the transmission of traffi c information
broadcast by a station which belongs
to the same network as the station to
which you are listening.
In order to benefi t from this, select the
traffi c information programme
TA .
Using the AF
(alternative frequency)
function on the FM waveband
The
RDS (Radio Data System) ena-
bles you to continue listening to the
same station irrespective of the fre-
quency that it uses in your current
location. The audio equipment con-
tinuously searches for the transmitter
which provides the best reception.
Press this button suc-
cessively to activate or
deactivate the function.
On FM, the multifunction display will
indicate:
- "TP" or "TP EON" : the radio
transmits a programme while
awaiting the broadcasting of
traffi c information.
- "TA" or "TA EON" : the
programme transmitted by the
radio is put on standby while
awaiting the broadcasting of
traffi c information.
If you wish to interrupt the transmission
of a message, press this button again.
Traffic information
programme (TA)
Press this button suc-
cessively to activate
or deactivate the func-
tion.
The screen will indicate:
- "AF" if the function is activated,
- "AF REG" if the function is
activated at regional level,
- "AF" fl ashing if the function is not
available. When
FM is selected,
press this button:

Notes: the volume of the traf-
fi c information is independent
of the volume of normal radio
listening.
You can adjust it using the volume
button, when the TA programme is
being transmitted.
The setting will be stored and will be
used during subsequent message
transmissions.
RDS
- "no pty" is displayed,
- then press the button briefl y to select a programme.
After a few seconds without any
action, your selection is stored.

2
28
AUDIO EQUIPMENT CD eject Selection of the source: CD or
CD changer or auxiliary Selection of the next track
Playing of the start of each track on the CD: brief press
 : fast forwards play

 : fast backwards play Selection of the previous track
Random playing of the tracks on the CD currently being played
CD changer:

 : selection of the previous CD

 : selection of the next CD CD: repeating of the current track/CD changer, press
for more than 2 seconds: repeating of the current CD
CD PLAYER OR CD CHANGER

2
29
AUDIO EQUIPMENT
Press this button to
select the next track.
CD PLAYER AND CD CHANGER FUNCTIONS
Introscan (SCAN) Press this button to
listen to the start of
each track on the cur-
rent CD.
Fast play
Press and hold one of
these buttons for fast
forwards or backwards
play respectively.
The fast play stops
when the button is re-
leased. When a CD is inserted,
printed face upper-
most, play begins au-
tomatically.
If there is a CD in the player already,
press this button.
CD PLAYER FUNCTIONS Repeating of a track on the
CD (RPT)
Random playing of the CD
(RAND) When the CD player
is selected, press this
button. If you wish to listen to
the current track again,
press this button. To
cancel the repetition,
press the button again.
CD eject Press this button to
eject the CD from the
player.
The tracks on the CD will be played
in a random order. Press the button
again to return to normal play.
The random play mode is deacti-
vated when the audio equipment is
switched off. The use of copied CDs may
cause faults.
Insert circular CDs only.
Selection of a track on a CD
Press this button to
return to the start of
the current track or
to select the previous
track. Selection of the CD player

2
28
AUDIO EQUIPMENT CD eject Selection of the source: CD or
CD changer or auxiliary Selection of the next track
Playing of the start of each track on the CD: brief press
 : fast forwards play

 : fast backwards play Selection of the previous track
Random playing of the tracks on the CD currently being played
CD changer:

 : selection of the previous CD

 : selection of the next CD CD: repeating of the current track/CD changer, press
for more than 2 seconds: repeating of the current CD
CD PLAYER OR CD CHANGER

2
29
AUDIO EQUIPMENT
Press this button to
select the next track.
CD PLAYER AND CD CHANGER FUNCTIONS
Introscan (SCAN) Press this button to
listen to the start of
each track on the cur-
rent CD.
Fast play
Press and hold one of
these buttons for fast
forwards or backwards
play respectively.
The fast play stops
when the button is re-
leased. When a CD is inserted,
printed face upper-
most, play begins au-
tomatically.
If there is a CD in the player already,
press this button.
CD PLAYER FUNCTIONS Repeating of a track on the
CD (RPT)
Random playing of the CD
(RAND) When the CD player
is selected, press this
button. If you wish to listen to
the current track again,
press this button. To
cancel the repetition,
press the button again.
CD eject Press this button to
eject the CD from the
player.
The tracks on the CD will be played
in a random order. Press the button
again to return to normal play.
The random play mode is deacti-
vated when the audio equipment is
switched off. The use of copied CDs may
cause faults.
Insert circular CDs only.
Selection of a track on a CD
Press this button to
return to the start of
the current track or
to select the previous
track. Selection of the CD player

2
30
AUDIO EQUIPMENT Press this button.
CD CHANGER FUNCTIONS Random playing of a CD
(RAND) When the CD changer
is selected, press this
button for 2 seconds.
The tracks of the current CD will be
played in a random order.
Press the button again for 2 seconds
to return to normal play.
Selection of a CD Press one of these
buttons on the audio
equipment to select
the previous or next
CD respectively. Repeating of a CD (RPT)
If you wish to listen to
the current CD again,
press and hold this
button.
The use of copied CDs may
cause faults.
Insert circular CDs only.
To cancel the repetition, press the
button again.
Selection of the CD changer