PEUGEOT 206 2006 Owners Manual

147Practical information-
WHEELS
Bolt covers
Alloy wheel bolts are covered by chrome trims.
Use the yellow tool 4 to remove the trims before slackening the bolts.
Tool 4 is located:
- on the saloon, on the rear right inner panel of the boot,- on the 206 SW, in the jack storage compartment,- on the 206 GTi 180, in the box lo-cated on the left-hand side of the boot.
Fitting the spare wheel
If your vehicle is equipped with a steel spare wheel, when fitting it, it is normal to notice that the bolt washers do not come into contact with the rim. The spare wheel is secured by the cone shape of each bolt.
Wheel anti-theft bolts
If your wheels are fitted with anti-theft bolts (one per wheel), the chrome-plated trim cap and then the plastic cover on the wheel must be removed, using the yellow tool (located in the box fixed to the left-hand side of the boot), before slackening the bolt using the anti-theft socket (located in the glove box) and the wheelbrace, located in the boot rear right inner panel.
Note: take a careful note of the code number engraved on the head of the anti-theft socket. This will enable you to obtain a duplicate anti-theft socket from a PEUGEOT dealer.
Fitting snow tyres
If you fit snow tyres that are mounted on steel rims onto your vehicle, it is essential that you use special bolts available from your PEUGEOT dealer.

Practical information146 -
PUNCTURES (206 )
Because this version does not pos-sess a spare wheel, you will find a repair kit (two tyre repair aerosols) stored in a box 1 secured by a strap on the left-hand side of the boot.
 Turn the wheel so that the valve is at ground level.
 Shake the aerosol vigorously be-fore use. In very cold weather, warm the aerosol for a few min-utes in your hands.
 Fix the aerosol connector onto the valve, keeping it centralised.
 Hold the valve against the hole in the wheel rim and at the same time empty the aerosol, keeping it upright.
 Maintain the pressure firmly for one minute.
 Remove the connector and im-mediately drive at least 3 miles (5 km).
 If possible, check the pressure of the tyre.
 Then immediately drive at moder-ate speed to the nearest garage.
The aerosol cans enable you to carry out a tem-porary repair (maximum speed 50 mph (80 km/h)).
After use, the tyre must be re-placed. As the aerosol cans are pressurised, they must not be exposed to a temperature above 50 °C.
Store them away from heat in their insulated storage box.
CHANGING A WHEEL
Tools
- The jack, the chock and the bolt cover tool are located in a box 1secured by a strap on the left-hand side of the boot.- The wheelbrace is secured on the boot rear right inner panel.
Using the repair aerosols
(Read the instructions for use on the aerosols also).
 If possible remove the object which caused the puncture and deflate the tyre.
Wheel changing procedure
The wheels of your 206 GTi 180 are fitted with anti-theft bolts.
The wheels are changed in the same way as on the saloon.
Refer to the corresponding sections.

147Practical information-
WHEELS
Bolt covers
Alloy wheel bolts are covered by chrome trims.
Use the yellow tool 4 to remove the trims before slackening the bolts.
Tool 4 is located:
- on the saloon, on the rear right inner panel of the boot,- on the 206 SW, in the jack storage compartment,- on the 206 GTi 180, in the box lo-cated on the left-hand side of the boot.
Fitting the spare wheel
If your vehicle is equipped with a steel spare wheel, when fitting it, it is normal to notice that the bolt washers do not come into contact with the rim. The spare wheel is secured by the cone shape of each bolt.
Wheel anti-theft bolts
If your wheels are fitted with anti-theft bolts (one per wheel), the chrome-plated trim cap and then the plastic cover on the wheel must be removed, using the yellow tool (located in the box fixed to the left-hand side of the boot), before slackening the bolt using the anti-theft socket (located in the glove box) and the wheelbrace, located in the boot rear right inner panel.
Note: take a careful note of the code number engraved on the head of the anti-theft socket. This will enable you to obtain a duplicate anti-theft socket from a PEUGEOT dealer.
Fitting snow tyres
If you fit snow tyres that are mounted on steel rims onto your vehicle, it is essential that you use special bolts available from your PEUGEOT dealer.

Practical information148 -
Dipped headlamps H7 55 W/main beam headlamps H1 55 W
 Remove the protective cover Afor the H7 55 W bulb or B for the H1 55 W bulb.
 Disconnect the connector(s) C.
 Press the end of the secur-ing clip(s) D to remove it(them). Change the faulty bulb.
CHANGING A BULB
To make access easier, on the right-hand side, first remove the screen wash reservoir filler pipe:
 align the notches by turning,
 pull upwards.
1. Dipped beam headlamps/main beam headlamps
2. Side lights
3. Direction indicators
 On fitting, ensure that the direc-tion notches are in the correct po-sition and that the securing clip(s) is(are) secured correctly.
 Reconnect the connector.
 Replace the protective cover(s), then the screen wash reservoir filler pipe (right-hand side).

149Practical information-
Amber direction indicators PY 21 W
 Turn the pin connector 3 a quarter turn (towards the front of the vehicle) and remove it.
 Change the bulb.
Saloon
Amber direction indicator
side repeater WY 5 W
 Push the repeater forwards and release it.
 Remove the repeater and change it.
It can be obtained from a PEUGEOT dealer.
206 SW
1. Direction indicators P 21 W.
2. Reversing lights P 21 W.
3. Brake lights/side lights P 21/5 W.
Side lights W 5 W
 Turn the pin connector 2 a quarter turn and remove it.
 Change the bulb.
Handle the bulbs with a dry cloth.
The headlamps are fit-ted with polycarbon glass with a protective coating. Do not clean them using a dry or abra-sive cloth, or using detergents or solvents.
Use a sponge and soapy water.

151Practical information-
Press under the access flap to release it.
Open the flap.
Turn the cover to remove it.
Disconnect the bulb.
Press the two ends of the securing clip to release the bulb.
Rear fog lamp P 21 W
Unclip the lamp and release the assembly.
Turn the pin connector a quarter turn and remove it.
Change the bulb.
Number plate lights W 5 W
Insert a thin screwdriver into one of the outer holes of the transparent cover.
Push it outwards to unclip it.
Remove the transparent cover.
Change the faulty bulb.

149Practical information-
Amber direction indicators PY 21 W
 Turn the pin connector 3 a quarter turn (towards the front of the vehicle) and remove it.
 Change the bulb.
Saloon
Amber direction indicator
side repeater WY 5 W
 Push the repeater forwards and release it.
 Remove the repeater and change it.
It can be obtained from a PEUGEOT dealer.
206 SW
1. Direction indicators P 21 W.
2. Reversing lights P 21 W.
3. Brake lights/side lights P 21/5 W.
Side lights W 5 W
 Turn the pin connector 2 a quarter turn and remove it.
 Change the bulb.
Handle the bulbs with a dry cloth.
The headlamps are fit-ted with polycarbon glass with a protective coating. Do not clean them using a dry or abra-sive cloth, or using detergents or solvents.
Use a sponge and soapy water.

Practical information150 -
Unclip the top of the boot trim using a coin.
Unscrew the two wing bolts using the wheelbrace if necessary.
Release the light unit.
Disconnect the connector. Move aside the tabs 1 and remove the bulb holder 2.
Change the faulty bulb.
When refitting, refit the boot trim by engaging it from the bottom then clipping the top.
Rear lights (saloon)
Unclip the boot side trim.
Unclip the foam cover and reach behind the cover to locate the wing nut.
Remove the wing nut.
Release the light unit.
Press the lug A and disconnect the connector.
Remove the foam.
Move aside the tabs B and remove the bulb holder.
Change the faulty bulb.
When refitting, ensure that the bulb holder, the light and the foam cover are repositioned correctly.
Third brake light 5 bulbs W 5 W (saloon)
Using a 10 mm spanner, unscrew the 2 nuts A.
Release the light unit.
Squeeze the two tabs B to release the bulb holder.
Change the faulty bulb.
Third brake light (206 SW)
This is fitted with diodes.
In the event of a fault, consult a PEUGEOT dealer.

151Practical information-
Press under the access flap to release it.
Open the flap.
Turn the cover to remove it.
Disconnect the bulb.
Press the two ends of the securing clip to release the bulb.
Rear fog lamp P 21 W
Unclip the lamp and release the assembly.
Turn the pin connector a quarter turn and remove it.
Change the bulb.
Number plate lights W 5 W
Insert a thin screwdriver into one of the outer holes of the transparent cover.
Push it outwards to unclip it.
Remove the transparent cover.
Change the faulty bulb.

Practical information152 -
CHANGING A FUSE
The fuse boxes are located under the fascia and in the engine compart-ment.
CorrectIncorrect
Pliers A
Fascia fuse box
Unscrew the catch a quarter turnusing a coin then remove the cover to gain access to the fuses.
The spare fuses and the pliers A are fitted inside of the fascia fuse box lid.
Removing and fitting a fuse
Before changing a fuse, the cause of the fault must be found and remedied. The fuse numbers are indicated on the fuse box.
Use the pliers A.
Always replace a faulty fuse with a fuse of the same rating .