light PEUGEOT 206 2008 Owner's Manual

Page 70 of 127

VISIBILITY
64 -
"Follow me home" lighting
When you leave your vehicle, the
side lights and dipped headlamps
can be left on for approximately
30 seconds.
To do this:
- place the key in the STOP
position,
- place the lights stalk in the 0 position,
- lash the headlamps,
- get out of the vehicle and lock it.AUTOMATIC SWITCHING ON
OF LIGHTS
The side lights and dipped beam
headlamps switch on automatical -
ly if the light is poor and when the
windscreen wipers operate continu -
ously and switch off when the light
becomes bright enough or the wind -
screen wipers are switched off.
In foggy weather or in snow, the
brightness sensor can detect suf-
icient light, the lights will not
come on automatically. If neces-
sary, the dipped headlamps must
be switched on manually.
This function is active when the ve -
hicle is supplied to the customer.
To disarm or activate the function:
- Place the key in the accessories position (1st notch),
- Place the lights stalk in the AUTO/0 position,
- Press the end of the lights stalk for more than four seconds.
Do not cover the brightness sen-
sor, coupled with the rain sensor,
located in the centre of the wind-
screen, behind the interior mirror.
It is used for automatic switching
on of the lights. Operating check
In good or rainy weather,
both day and night, the
front fog lamps and the
rear fog lamp are dazzling
and are prohibited.
Do not forget to switch them off
when they are no longer needed.
Direction indicators
(lashers) Left: downwards.
Right: upwards. Disarming
The disarmed function is accompa-
nied by an audible signal.
When the driver uses the manual
lighting controls, the function is tem
-
porarily disarmed.
If the brightness sensor does not
function correctly, the lights come
on accompanied by an audible signal
and a message on the multifunction
display.
Consult a PEUGEOT dealer.
Activation
The activated function is accompa-
nied by an audible signal and a mes-
sage on the multifunction display.

Page 71 of 127

VISIBILITY
64 -
"Follow me home" lighting
When you leave your vehicle, the
side lights and dipped headlamps
can be left on for approximately
30 seconds.
To do this:
- place the key in the STOP
position,
- place the lights stalk in the 0 position,
- lash the headlamps,
- get out of the vehicle and lock it.AUTOMATIC SWITCHING ON
OF LIGHTS
The side lights and dipped beam
headlamps switch on automatical -
ly if the light is poor and when the
windscreen wipers operate continu -
ously and switch off when the light
becomes bright enough or the wind -
screen wipers are switched off.
In foggy weather or in snow, the
brightness sensor can detect suf-
icient light, the lights will not
come on automatically. If neces-
sary, the dipped headlamps must
be switched on manually.
This function is active when the ve -
hicle is supplied to the customer.
To disarm or activate the function:
- Place the key in the accessories position (1st notch),
- Place the lights stalk in the AUTO/0 position,
- Press the end of the lights stalk for more than four seconds.
Do not cover the brightness sen-
sor, coupled with the rain sensor,
located in the centre of the wind-
screen, behind the interior mirror.
It is used for automatic switching
on of the lights. Operating check
In good or rainy weather,
both day and night, the
front fog lamps and the
rear fog lamp are dazzling
and are prohibited.
Do not forget to switch them off
when they are no longer needed.
Direction indicators
(lashers) Left: downwards.
Right: upwards. Disarming
The disarmed function is accompa-
nied by an audible signal.
When the driver uses the manual
lighting controls, the function is tem
-
porarily disarmed.
If the brightness sensor does not
function correctly, the lights come
on accompanied by an audible signal
and a message on the multifunction
display.
Consult a PEUGEOT dealer.
Activation
The activated function is accompa-
nied by an audible signal and a mes-
sage on the multifunction display.

Page 75 of 127

VISIBILITY
68 -
ELECTRIC WINDOWS
2. Passenger's electric window
switch.
REAR QUARTER LIGHTS
(3 DOOR)
To partially open the rear windows,
tilt lever then push the window. Always remove the key
from the ignition when
leaving the vehicle, even
for a short time.
If an obstacle is detected when
operating the electric windows,
you must reverse the movement
of the window. To do this, press
the control concerned.
When the driver operates the pas-
senger electric window controls,
he must ensure that no one is pre-
venting correct closing of the win -
dows.
The driver must ensure that pas-
sengers use the electric windows
correctly.
Be aware of children when operat -
ing the windows.
This switch enables the rear windows
to be locked whatever their position.
A 1st press activates the control (the
indicator light on the button comes
on) and a 2nd press deactivates it
(the indicator light on the button goes
out).
Temporary disarming of the
rear windows (child safety)
1. Driver's electric window switch
- Manual operation:
Press or pull switch 1 gently. The
window stops as soon as the
switch is released.
- Automatic operation:
Press or pull switch 1 irmly.
One touch completely opens or
closes the window.
Automatic closing only operates
when the engine is running and only
on the driver's electric window. 3. Rear left electric window
switch.
4. Rear right electric window switch.

Page 78 of 127

71
LAYOUT
-
COURTESY LIGHTS
Map-reading light (button B)
With the key in the accessories or
ignition on position, turn button B to
the left or to the right.
AREAS FOR TOLL CARDS/
CAR PARK TICKETS
The athermic windscreen has two
non-relective zones located either
side of the base of the interior mirror.
They are intended for afixing toll
cards and/or car park tickets.
SUN VISOR
The sun visors are itted with a vanity
mirror, with a concealing lap on the
driver’s side.
Permanently off
Permanently on when the
key is in the accessories po-
sition or with the ignition on.
Front courtesy light (button A)
In this position, it comes on
for about 30 seconds:
- on unlocking the vehicle,
- when opening a door,
- when opening the tailgate and the rear screen (206 SW),
- on switching off the ignition.
It switches off on locking the vehicle.The courtesy light lashes while driving if
a door or the boot is not closed correctly.

Page 79 of 127

LAYOUT
72 -
GLOVE BOX
To open the glove box, lift the handle.
The light comes on when the cover
is opened.
1. Handbook pack storage.
2. Can holder.
3. Pen holder.
4. Spectacles storage.
5. Map storage.
6. Coin storage.
FRONT ASHTRAY
To empty, close the cover.
Pull the lug and release the ashtray
upwards.
LIGHTER
Press and wait a few moments until it
springs out automatically.
It is supplied with power with the igni -
tion key in the accessories position
(1st notch).

Page 81 of 127

DRIVING
74 -
'PORSCHE TIPTRONIC
SYSTEM' AUTOMATIC
GEARBOX
The four speed automatic gearbox
offers a choice between the comfort
of integral automatic operation ,
enhanced by a sport and a snow pro-
gramme, or manual gear changing .
Gear selection gate
F Move the lever in the gate to
select a position.
The indicator light corresponding to the position selected appears
on the instrument panel screen.
P ark: to immobilise the vehicle and
to start the engine , with the hand-
brake on or off.
R everse: to reverse (select this
position with the vehicle stationary,
engine at idle).
N eutral: to start the engine and to
park , with the handbrake on.
If position N is inadvertently engaged
while driving, allow the engine to re -
turn to idle before engaging position D
to accelerate.
D rive: for driving in automatic mode.
Manual: for selection of gears.
S : sport programme.
T : snow programme. Moving Off
With the engine running, to move off
from position
P:
F it is essential to press the
brake pedal to exit position P ,
F select position R, D or M, then
gradually release the pressure
on the brake pedal; the vehicle
moves off immediately.
You can also move off from position N:
F release the handbrake, with your
foot on the brake,
F select position R, D or M, then
gradually release the pressure
on the brake pedal; the vehicle
moves off immediately.
Starting the engine
F with the handbrake on, select
position P or N in the gate,
F turn the ignition key to the Start
position. WARNING
When the engine is at idle, brakes not
applied, if position
R, D or M is se-
lected, the vehicle moves even with -
out the accelerator being pressed.
For this reason, do not leave children
unsupervised inside the vehicle,
with the engine running .
When maintenance operations need
to be carried out with the engine run -
ning, apply the handbrake and select
position P.

Page 85 of 127

77
DRIVING
-
SPEED LIMITER
This speed limiter, of the new gener -
ation, has a display on the instrument
panel to indicate the programmed
speed.
It prevents exceeding of the vehicle
speed programmed by the driver.
When the programmed speed is
reached, pressing the accelerator
pedal no longer has any effect.
The limiter operates with a pro -
grammed speed of at least 18 mph
approx. (30 km/h); it remains active
regardless of any action on the brake
and clutch pedals.
The operating actions must be
carried out:
- when stationary, with the
engine running,
or
- with the vehicle moving. The indicator light on the in-
strument panel comes on at
the same time.
Instrument panel display
When the speed limiter function is
active, pressing this button displays
the distance recorders.
After a few seconds or when this but
-
ton is pressed again, the display re -
turns to the speed limiter function.
Selecting the function
F Place the dial 1 in the LIMIT
position. The limiter is not yet
active. By default, the display
indicates: Storing a speed
A speed can be stored without acti
-
vating the limiter.
Press buttons 2 and 3 briely to de -
crease or increase by 1 mph (1 km/h).
An extended press decreases or
increases by 5 mph (5 km/h).
A maintained press decreases or
increases the programmed speed in
steps of 5 mph (5 km/h).
Activating/deactivating the limiter
Pressing button 4 once activates the
limiter, pressing the button again de -
activates it.
When the limiter is active, the display
indicates (e.g. at 70 mph (110 km/h)):

Page 87 of 127

79
DRIVING
-
CRUISE CONTROL
This cruise control, of the new gener -
ation, has a display on the instrument
panel to indicate the memorised ref-
erence speed.
It enables the vehicle to maintain a
steady speed programmed by the
driver.
In order for it to be memorised or ac-
tivated, the vehicle speed must be
greater than 24 mph approx. (40 km/h)
with at least fourth gear engaged for
vehicles itted with a manual gearbox.
On vehicles itted with an automatic
gearbox, the lever must be in position D
at a speed greater than 24 mph approx.
(40 km/h), or in at least second gear in
sequential mode.
The indicator light on the in-
strument panel comes on at
the same time.
Instrument panel display
When the cruise control function is ac-
tivated, pressing this button enables
you to display the distance recorders.
After a few seconds or when this but
-
ton is pressed again, the display re -
turns to the cruise control function.
Selecting the function
F Place switch 1 in the CRUISE
position. The cruise control is
not yet active and no speed has
been memorised. The display
indicates in succession: First activation/memorising a
reference speed
As soon as you reach the chosen
speed, press button
2 or 3. This
memorises the speed and the display
indicates (e.g. at 70 mph (110 km/h)):
Note: It is possible to accelerate and
drive momentarily at a speed greater
than the memorised speed. The value
memorised lashes. When the accel -
erator pedal is released, the vehicle
returns to the memorised speed.
Cancelling the cruise control
If you wish to cancel the cruise control:
F Press button 4 or the brake or
clutch pedal.
The display indicates (e.g. at 70 mph
(110 km/h)):
The indicator light on the instrument
panel switches off.

Page 89 of 127

81
SAFETY
-
ANTI-LOCK BRAKING
SYSTEM (ABS) AND
ELECTRONIC BRAKE FORCE
DISTRIBUTION (EBFD)
The ABS, in conjunction with the
electronic brake force distribution,
increases the stability and manoeu-
vrability of your vehicle on braking,
in particular on poor or slippery road
surfaces.
When changing wheels (tyres and
rims), make sure that these are ap -
proved.
The anti-lock braking system comes
into operation automatically when
there is a risk of wheel lock.
EMERGENCY BRAKING
ASSISTANCE SYSTEM
In an emergency, this system ena -
bles the optimum braking pressure to
be reached more quickly, thus reduc -
ing the stopping distance.
It is triggered by the speed at which the
brake pedal is activated. The effect of
this is a reduction in the resistance of
the pedal and an increase in braking
eficiency.
When braking in an emergency,
press irmly without releasing the
pressure.
Depending on the force of the decel-
eration, the hazard warning lights are
switched on automatically. They are
switched off automatically on accel -
eration.
When this warning light
comes on, accompanied by
a buzzer and a message, it
indicates that there is a mal-
function of the ABS, which can cause
a loss of control of the vehicle when
braking. When this warning light
comes on, connected to the
STOP
warning light, accom -
panied by a buzzer and a
message, it indicates that there is a
malfunction of the electronic brake
force distribution, which can cause
a loss of control of the vehicle when
braking.
Stop immediately.
In both cases, consult a PEUGEOT
dealer.
Normal operation of the ABS may
make itself felt by slight vibrations
of the brake pedal.
In emergency braking, press
very irmly without releasing the
pressure.

Page 90 of 127

SAFETY
82 -
TRACTION CONTROL (ASR)
AND DYNAMIC STABILITY
CONTROL (ESP)Disarming the ASR/ESP systems
In exceptional conditions (starting a
vehicle which is bogged down, stuck
in snow, on soft ground), it may be
advisable to disarm the ASR and
ESP systems, so that the wheels can
move freely and regain grip.
F Press the "ESP OFF" switch,
located under the steering wheel
to the right. Operating check
The ASR/ESP systems
offer exceptional safety
in normal driving, but this
should not encourage the
driver to take extra risks or drive at
high speed.
The correct functioning of these
systems depends on observation
of the manufacturer's recommen-
dations regarding wheels (tyres
and rims), the braking compo -
nents, the electronic components
and the PEUGEOT assembly and
operation procedures.
After an impact, have the system
checked by a PEUGEOT dealer.
Operation of the ASR and ESP
systems The switch lights up and the
warning light comes on, ac
-
companied by a message
on the multifunction display:
the ASR and ESP systems are dis-
armed.
These are triggered again :
F automatically if the ignition is
switched off,
F manually by pressing the switch
again. When a malfunction of the
systems occurs, the switch
light lashes and the warning
light comes on.
Contact a PEUGEOT dealer to have
the systems checked.
The warning light lashes if
the ASR or ESP is activated.
Activation of the ASR and ESP
systems
When the ignition is on, the ASR and
ESP systems are always active.
These systems are linked and com-
plement the ABS.
The ASR system optimises drive to
prevent the wheels skidding, by act
-
ing on the brakes of the drive wheels
and on the engine. It also allows the
directional stability of the vehicle to
be improved on acceleration.
If there is a variation between the tra -
jectory followed by the vehicle and
that required by the driver, the ESP
system automatically acts on the en-
gine and the brake of one or more
wheels, in order to put the vehicle
back on course, within the limits of
the laws of physics.

Page:   < prev 1-10 11-20 21-30 31-40 next >