Peugeot 206 CC Dag 2004 Owner's Manual

96
21-06-2004
97
21-06-2004
PRACTICAL INFORMATION
CHANGING A BULB
Dipped/main headlamps
H7 55W
- Pull the tab A upwards and remove
the protective cover.
- Disconnect the connector.
- Press the end of the securing clip to remove it. Change the faulty
bulb.
- On itting, ensure that the direction notches are in the correct position
and that the clip is secured
correctly.
- Reconnect the connector.
- Replace the protective cover. Side lights W5W
Turn the pin connector
B a quarter
turn and remove it.
Change the bulb. PEUGEOT recommends
the use of H7 bulbs of
brands:
- GE/TUNGSRAM,
- PHILIPS,
- OSRAM,
to avoid damaging the
headlamps.
These comply with the anti-
UV (ultraviolet) speciications
necessary for the correct operation
and reliability of the headlamps.
The headlamps are itted with
polycarbon glass with a protective
coating. We strongly advise
against cleaning them using a
dry or abrasive cloth or using
detergents or solvents.
Use a soft, damp cloth.
Amber bulbs must be replaced
with bulbs of identical speciication
and colour.
Remarks
- Only touch the bulbs with a dry cloth.
- To replace the bulbs on the right side, remove the wash-wipe reservoir iller pipe
irst.
- Condensation may form inside the headlamps. It will disappe ar when the lights
are used.

98
21-06-2004
99
21-06-2004
PRACTICAL INFORMATION
Amber direction indicators
PY21W
Turn the pin connector C a quarter
turn and remove it.
Change the bulb. Amber direction indicator side
repeater WY5W
Push the repeater forwards
or backwards and release the
assembly.
Hold the connector and turn the
transparent cover a quarter turn.
Change the bulb.

98
21-06-2004
99
21-06-2004
PRACTICAL INFORMATION
1. Direction indicators P21W.
2. Reversing lights P21W.
3. Brake lights/side lights P21/5W.Rear lights
Unclip the luggage compartment
side trim.
Remove the wing bolt.
Release the light unit.
Press the lug
A and disconnect the
connector.
Remove the foam.
Move aside the tabs B and remove
the bulb holder.
Change the faulty bulb.
When reitting, ensure that the bulb
holder and the light are repositioned
correctly. Front fog lamps H1 55W
Press underneath the access lap to
release it.
Open the lap.
Turn the cover to remove it.
Disconnect the bulb.
Pinch both ends of the securing clip
to release the bulb.

100
21-06-2004
101
21-06-2004
Rear fog lamp P21W
Unclip the light and release the
assembly.
Turn the pin connector a quarter turn
and remove it.
Change the bulb.
PRACTICAL INFORMATION
Number plate lights W5W
Insert a thin screwdriver into one of
the exterior holes of the transparent
cover.
Push it outwards to unclip it.
Remove the transparent cover.
Change the faulty bulb.

102
21-06-2004
103
21-06-2004
PRACTICAL INFORMATION
Removing and reitting a fuse
Before changing a fuse, the cause
of the fault must be found and
remedied. The fuse numbers are
indicated on the fuse box.
Use the pliers A.CHANGING A FUSE
The fuse boxes are located under the instrument panel and in the
engine compartment.
Fascia fuse box
Unscrew the catch a quarter turn
using a coin, then remove the cover
to gain access to the fuses.
The spare fuses and the pliers A are
secured on the inside of the fascia
fuse box cover. Correct Incorrect
Pliers A Always replace a faulty fuse (fault
registered depending on fuse) with a fuse of the same rating.

102
21-06-2004
103
21-06-2004
PRACTICAL INFORMATION
Removing and reitting a fuse
Before changing a fuse, the cause
of the fault must be found and
remedied. The fuse numbers are
indicated on the fuse box.
Use the pliers A.CHANGING A FUSE
The fuse boxes are located under the instrument panel and in the
engine compartment.
Fascia fuse box
Unscrew the catch a quarter turn
using a coin, then remove the cover
to gain access to the fuses.
The spare fuses and the pliers A are
secured on the inside of the fascia
fuse box cover. Correct Incorrect
Pliers A Always replace a faulty fuse (fault
registered depending on fuse) with a fuse of the same rating.

102
21-06-2004
103
21-06-2004
PRACTICAL INFORMATION
Fuse RatingFunctions
1
15AHeated seat - Alarm
4 20A Mulltifunction screen - Navigation control unit - Boot lightin
g - Audio system - Retractable roof
control unit - Steering wheel controls - Trailer
5 15A Automatic gearbox diagnostics
6 10A Coolant level - Automatic gearbox - Audio system - Steering whe el angle sensor (ESP)
7
15AAlarm itted as an accessory
9
30AHydraulic pump
10
40ADriving mirror demisting
11
15AWindscreen wiper
12
30AFront windows
14
10AEngine module - Air bags - Steering wheel stalk - Rain sensor
15
15AInstrument panel - Multifunction screen - Navigation control unit - Air conditionin g - Audio system
1630ALocking/unlocking of doors
20
10ARight-hand brake light
21
15ALeft-hand brake light - 3rd brake light
22
20AFront courtesy light - Glove box lighting - Lighter
S1* Shunt PARC shunt

104
21-06-2004
105
21-06-2004
PRACTICAL INFORMATION
or
Your vehicle's electrical
circuit is designed to
operate with standard or
optional equipment.
Before installing additional
electrical equipment or
accessories, consult a PEUGEOT
dealer.
Some electrical accessories, or the
way in which they are itted, may
adversely affect the operation of
your vehicle (the electronic control
circuits, the radio circuit and the
electrical charging circuit ).
PEUGEOT does not accept
any responsibility for expenses
incurred by repairs or for any faults
resulting from the installation of
additional accessories which are
not supplied or recommended
by PEUGEOT and which were
not installed in accordance with
the manufacturer's instructions,
in particular equipment with
a consumption greater than
10 milliamps.
Engine compartment fuse box
To access the fuse box located in
the engine compartment (next to the
battery), unclip the cover.
Fuse no. Rating Functions
1* 20A Fan unit
2* 60A ABS/ESP
3*
30AABS/ESP
4*
70ASupply to built-in systems interface
5*
70ASupply to built-in systems interface
6*
-Not used
7* 30A Ignition lock supply
8* - Not used
* The maxi fuses provide additional protection for the electrica l systems. Any
work must be carried out by a PEUGEOT dealer. After changing the fuse, close the
cover very carefully.

104
21-06-2004
105
21-06-2004
PRACTICAL INFORMATION
Fuse RatingFunctions
1
10AReversing lights switch - Speed sensor
2 15A Canister solenoid valve- Fuel pump
3 10A ABS/ESP engine control unit - ESP stop switch
4 10A Automatic gearbox control unit - Engine control unit
5
-Not used
6
15AFront fog lamps
7
20AWindscreen wash pump
8
20AFan unit relay - Engine control unit - Engine management sole noid valve
9
15ALeft-hand dipped beam
10
15ARight-hand dipped beam
11
10ALeft-hand main beam
12
15ARight-hand main beam
13
15AHorn
14
10AFront windscreen wash pump
15
30AThrottle unit heater - Oxygen sensor - Engine control unit - Ig nition coil - Engine management
solenoid valve - Injectors
16 30A Air pump relay
17 30A High and low speed windscreen wiper
18 40A Air conditioning fan

106
21-06-2004
107
21-06-2004
PRACTICAL INFORMATIONECONOMY MODE FUNCTION
After the engine has stopped, with
the key in the accessories position,
certain functions (windscreen wiper,
electric windows, courtesy lights,
audio equipment etc.) can only be
used for thirty minutes, to prevent
discharging the battery.
Once the thirty minutes are over, the
message "Economy mode active"
appears on the multifunction display
and the active functions are put on
standby.
A lat battery will prevent the engine
from starting.
BATTERY
To charge the battery using a
battery charger:
- Disconnect the battery,
- Follow the instructions for use given by the battery charger
manufacturer,
- Reconnect starting with the negative (-) terminal,
- Check that the terminals and connectors are clean. If they are
covered with sulphate (white or
greenish deposit), disconnect them
and clean them.
To start the vehicle from another
battery:
- Connect the red cable to the positive (+) terminals of the two
batteries,
- Connect one end of the green or black cable to the negative (-)
terminal of the slave battery,
- Connect the other end of the green or black cable to an earth point on
the broken down vehicle, as far as
possible from the battery,
Operate the starter, let the engine
run.
Wait for the engine to return to idle,
then disconnect the cables.
It is advisable to disconnect the
battery if the vehicle is not to be
used for a period of more than
one month.- Wait for 2 minutes after switching off the ignition
before disconnecting
the battery.
- Never disconnect a terminal when the engine is running.
- Never charge a battery without irst disconnecting the
terminals.
- Close the windows and the roof before disconnecting the
battery.
- After every reconnection of the battery, switch on the ignition
and wait 1 minute before
starting to allow the electronic
systems to be initialised. If slight
dificulties are experienced after
this, please consult a PEUGEOT
dealer.