PEUGEOT 206 SW 2005 Owners Manual

Practical information146 -
01-10-2005
147Practical information-
01-10-2005
SPECIAL FEATURES OF
ALLOY WHEELS
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool 4 to remove the
trims before slackening the bolts.
Tool 4 is located:
- on the saloon, on the rear right inner panel of the boot,
- on the 206 SW, in the jack storage compartment,
- on the 206 GTi 180, in the box located on the left-hand side of the
boot.
Fitting the spare wheel
If your vehicle is equipped with a
steel spare wheel, when itting it,
it is normal to notice that the bolt
washers do not come into contact
with the rim. The spare wheel is
secured by the cone shape of each
bolt.
Wheel anti-theft bolts
If your wheels are itted with anti-theft
bolts (one per wheel), the chrome-
plated trim cap and then the plastic
cover on the wheel must be removed,
using the yellow tool (located in the
box ixed to the left-hand side of the
boot), before slackening the bolt
using the anti-theft socket (located in
the glove box) and the wheelbrace,
located in the boot rear right inner
panel.
Note: take a careful note of the code
number engraved on the head of the
anti-theft socket. This will enable you
to obtain a duplicate anti-theft socket
from a PEUGEOT dealer.
Fitting snow tyres
If you it snow tyres that are mounted
on steel rims onto your vehicle, it
is essential that you use special
bolts available from your PEUGEOT
dealer.

Practical information148 -
01-10-2005
149Practical information-
01-10-2005
1a. Dipped headlamps H7 55W / main beam
headlamps H7 55W
F Pull the tab A upwards then
rearwards and remove the
protective cover.
F Disconnect the connector(s) B.
F Press the end of the securing
clip C to remove it. Change the
faulty bulb.
F On itting, ensure that the direction
notches are in the correct position
and that the clip is secured
correctly.
F Reconnect the connector.
F Replace the protective cover, then
the screen wash reservoir iller
pipe (right-hand side).
CHANGING A BULB
To make access easier, on the right-
hand side , irst remove the screen
wash reservoir iller pipe:
F align the notches by turning,
F pull upwards.
Depending on the version of your
vehicle, refer to the corresponding
dipped headlamps / main beam
headlamps combination.
1b. Dipped headlamps H7 55W / main beam
headlamps H1 55W
F Remove the protective cover D for
the H7 55W bulb or E for the H1
55W bulb.
F Disconnect the connector(s) F.
F Press the end of the securing
clip(s) G to remove it(them).
Change the faulty bulb.
F On itting, ensure that the direction
notches are in the correct position
and that the securing clip(s)
is(are) secured correctly.
F Reconnect the connector.
F Replace the protective cover(s),
then the screen wash reservoir
iller pipe (right-hand side).

Practical information
148 -
01-10-2005
149
Practical information
-
01-10-2005
3. Amber direction indicators
PY21W
F Turn the pin connector 3 a quarter
turn (towards the front of the
vehicle) and remove it.
F Change the bulb.
Saloon
Amber direction indicator side
repeater WY5W F
Push the repeater forwards and
release it.
F Remove the repeater and change
it.
It can be obtained from a PEUGEOT
dealer. 206 SW
1. Direction indicators P 21 W.
2. Reversing lights P 21 W.
3. Brake lights/side lights P 21/5 W.
2. Side lights W5W
F
Turn the pin connector 2 a quarter
turn and remove it.
F Change the bulb.
Handle the bulbs with a
dry cloth.
The headlamps are itted
with polycarbon glass with
a protective coating. Do not clean
them using a dry or abrasive
cloth, or using detergents or
solvents.
Use a sponge and soapy water.

Practical information150 -
01-10-2005
151Practical information-
01-10-2005
Front fog lamps H1 55 W
Press under the access lap to
release it.
Open the lap.
Turn the cover to remove it.
Disconnect the bulb.
Press the two ends of the securing
clip to release the bulb.
Rear fog lamp P 21 W
Unclip the lamp and release the
assembly.
Turn the pin connector a quarter turn
and remove it.
Change the bulb.
Number plate lights W 5 W
Insert a thin screwdriver into one of
the outer holes of the transparent
cover.
Push it outwards to unclip it.
Remove the transparent cover.
Change the faulty bulb.

Practical information
148 -
01-10-2005
149
Practical information
-
01-10-2005
3. Amber direction indicators
PY21W
F Turn the pin connector 3 a quarter
turn (towards the front of the
vehicle) and remove it.
F Change the bulb.
Saloon
Amber direction indicator side
repeater WY5W F
Push the repeater forwards and
release it.
F Remove the repeater and change
it.
It can be obtained from a PEUGEOT
dealer. 206 SW
1. Direction indicators P 21 W.
2. Reversing lights P 21 W.
3. Brake lights/side lights P 21/5 W.
2. Side lights W5W
F
Turn the pin connector 2 a quarter
turn and remove it.
F Change the bulb.
Handle the bulbs with a
dry cloth.
The headlamps are itted
with polycarbon glass with
a protective coating. Do not clean
them using a dry or abrasive
cloth, or using detergents or
solvents.
Use a sponge and soapy water.

Practical information150 -
01-10-2005
151Practical information-
01-10-2005
Rear lights (206 SW)
Unclip the top of the boot trim using
a coin.
Unscrew the two wing bolts using the
wheelbrace if necessary.
Release the light unit.
Disconnect the connector. Move
aside the tabs 1 and remove the bulb
holder 2.
Change the faulty bulb.
When reitting, reit the boot trim
by engaging it from the bottom then
clipping the top.
Rear lights (saloon)
Unclip the boot side trim.
Unclip the foam cover and reach
behind the cover to locate the wing
nut.
Remove the wing nut.
Release the light unit.
Press the lug A and disconnect the
connector.
Remove the foam.
Move aside the tabs B and remove
the bulb holder.
Change the faulty bulb.
When reitting, ensure that the bulb
holder, the light and the foam cover
are repositioned correctly.
Third brake light 5 bulbs
W 5 W (saloon)
Using a 10 mm spanner, unscrew the
2 nuts A.
Release the light unit.
Squeeze the two tabs B to release
the bulb holder.
Change the faulty bulb.
Third brake light (206 SW)
This is itted with diodes.
In the event of a fault, consult a
PEUGEOT dealer.

Practical information150 -
01-10-2005
151Practical information-
01-10-2005
Front fog lamps H1 55 W
Press under the access lap to
release it.
Open the lap.
Turn the cover to remove it.
Disconnect the bulb.
Press the two ends of the securing
clip to release the bulb.
Rear fog lamp P 21 W
Unclip the lamp and release the
assembly.
Turn the pin connector a quarter turn
and remove it.
Change the bulb.
Number plate lights W 5 W
Insert a thin screwdriver into one of
the outer holes of the transparent
cover.
Push it outwards to unclip it.
Remove the transparent cover.
Change the faulty bulb.

Practical information152 -
01-10-2005
153Practical information-
01-10-2005
CHANGING A FUSE
The fuse boxes are located under
the fascia and in the engine
compartment.Correct Incorrect
Pliers A
Fascia fuse box
Unscrew the catch a quarter turn
using a coin then remove the cover
to gain access to the fuses.
The spare fuses and the pliers A
are itted inside of the fascia fuse
box lid. Removing and itting a fuse
Before changing a fuse, the cause of the fault must be foun
d and remedied. The
fuse numbers are indicated on the fuse box.
Use the pliers A.
Always replace a faulty fuse with a fuse of the same rating .

Practical information154 -
01-10-2005
155Practical information-
01-10-2005
or
The electrical circuit of your
vehicle is designed to oper-
ate with standard or optional
equipment. Before installing
other electrical equipment
or accessories in your vehicle, con-
sult a PEUGEOT dealer.
Some electrical accessories or the
way in which they are itted may
have an adverse effect on the op-
eration of your vehicle (its electronic
control circuits, the audio circuit and
the electrical charging circuit).
PEUGEOT declines any responsi-
bility for expenses incurred by the
repair of your vehicle or for any
malfunctions resulting from the in-
stallation of auxiliary accessories,
not supplied and not recommend-
ed by PEUGEOT and not installed
in accordance with PEUGEOT’s
instructions, in particular for any
equipment the power consumption
of which exceeds 10 milliamps.
Fuse N° Rating Functions
1* 20 A Fan unit
2* 60 A ABS/ESP
3* 30 A ABS/ESP
4* 70 A Built-in systems interface supply
5* 70 A Built-in systems interface supply
6* - Not used
7* 30 A Ignition switch supply
8* 20 A Audio ampliier
Engine compartment fuse box
To gain access to the box in the engine compartment (next to t he battery), unclip
the cover.
After carrying out work, close the cover very carefully.
* The maxi fuses provide additional protection for the electrica l systems. Any
work on these must be carried out by a PEUGEOT dealer.

Practical information154 -
01-10-2005
155Practical information-
01-10-2005
Fuse N° RatingFunctions
1 10 A Pre-heat unit (diesel) - Water in diesel sensor - Reversing lights sw
itch -
Speed sensor - Air low sensor (diesel)
2 15 A Canister solenoid valve - Fuel pump
3 10 A ABS/ESP engine control unit - ESP brake switch
4 10 A Automatic gearbox control unit - Engine control unit
5 - Not used
6 15 A Front fog lamps
7 20 A Not used
8 20 A Fan assembly relay - Engine control unit - Diesel injection pump
-
Diesel high pressure regulator - Engine management solenoid valve
9 15 A Left dipped beam
10 15 A Right dipped beam 11 10 A Left main beam
12 15 A Right main beam
13 15 A Horn
14 10 A Front and rear windscreen wash pumps
15 30 A Throttle housing heater - Diesel injection pump - Oxygen sensor
-
Engine control unit - Air low sensor - Ignition coil - Engine mana gement solenoid valve -
Diesel heater - Injectors - Variable engine timing solenoid va lve (206 GTi 180) -
Engine variable air intake solenoid valve (206 GTi 180)
16 30 A Air pump relay
17 30 A High and low speed windscreen wiper
18 40 A Air conditioning fan