Peugeot 206 SW Dag 2005.5 Owners Manual

Comfort88 -
01-10-2005
89Comfort-
01-10-2005
Saloon and 206 SW

Comfort88 -
01-10-2005
89Comfort-
01-10-2005
206 GTi 180

Comfort90 -
01-10-2005
91Comfort-
01-10-2005
FRONT SEATS
1 - Forwards-backwards adjustment
Lift the control and slide the seat
towards the front or the rear.
2. Head restraint height and angle adjustment
(except 206 GTi 180)
To raise the restraint, pull it upwards.
The adjustment is correct when the
upper edge of the head restraint is
level with the top of the head.
The head restraint has a frame with
notches, which prevent the head
restraint dropping down (this is a
safety device in the event of an
impact).
To lower the head restraint, it is
necessary to push simultaneously:
- the button located on the left guide at the base of the head restraint,
- the head restraint downwards.
To remove the head restraint, press
the lug.
The angle of the head restraint can
also be adjusted. 4. Seat height adjustment
Pull the handle upwards.
Remove your weight from the seat to
raise, or press on the seat to lower.
5. Seat back angle adjustment
Push one of the two handles towards
the rear.
6. Heated seats switch
Press the switch. The temperature is
controlled automatically.
Press the switch again to stop
operation.
Never drive with the head
restraints removed; they
must be in place and
correctly adjusted. Rear head restraints
These have a high position for when
they are in use and a low position
for when they are stored. They are
removable.
To lower the head restraints, press
the lug.
To remove them, pull upwards as far
as the stop, then press the release
control.
3. Access to rear seats
(3 door), A or B according to
version
A - Pull one of the two handles and
push forwards to fold the seat back
and move the seat forwards.
On repositioning, the seat returns to
its initial position.
No person nor object must prevent
the seat from returning to its initial
position; returning to this position is
necessary for it to be locked.
It is impossible to access the rear
seats if the front seat is in the reclining
position.
B - Pull one of the two handles and
push forwards to fold the seat back.
On repositioning, the seat back
returns to its initial position.

Comfort90 -
01-10-2005
91Comfort-
01-10-2005
FRONT SEATS
1 - Forwards-backwards adjustment
Lift the control and slide the seat
towards the front or the rear.
2. Head restraint height and angle adjustment
(except 206 GTi 180)
To raise the restraint, pull it upwards.
The adjustment is correct when the
upper edge of the head restraint is
level with the top of the head.
The head restraint has a frame with
notches, which prevent the head
restraint dropping down (this is a
safety device in the event of an
impact).
To lower the head restraint, it is
necessary to push simultaneously:
- the button located on the left guide at the base of the head restraint,
- the head restraint downwards.
To remove the head restraint, press
the lug.
The angle of the head restraint can
also be adjusted. 4. Seat height adjustment
Pull the handle upwards.
Remove your weight from the seat to
raise, or press on the seat to lower.
5. Seat back angle adjustment
Push one of the two handles towards
the rear.
6. Heated seats switch
Press the switch. The temperature is
controlled automatically.
Press the switch again to stop
operation.
Never drive with the head
restraints removed; they
must be in place and
correctly adjusted. Rear head restraints
These have a high position for when
they are in use and a low position
for when they are stored. They are
removable.
To lower the head restraints, press
the lug.
To remove them, pull upwards as far
as the stop, then press the release
control.
3. Access to rear seats
(3 door), A or B according to
version
A - Pull one of the two handles and
push forwards to fold the seat back
and move the seat forwards.
On repositioning, the seat returns to
its initial position.
No person nor object must prevent
the seat from returning to its initial
position; returning to this position is
necessary for it to be locked.
It is impossible to access the rear
seats if the front seat is in the reclining
position.
B - Pull one of the two handles and
push forwards to fold the seat back.
On repositioning, the seat back
returns to its initial position.

Comfort90 -
01-10-2005
91Comfort-
01-10-2005
- position the seat belt under the belt holder 2,
- pull control 3 to unlock the seat
back 4,
- remove or lower the head restraint,
- tilt the seat back 4.
Always start with the seat, never
the seat back (risk of damage).
REAR SEATS
To fold the rear seats:
- lift the front of the seat cushion 1,
- tilt the seat cushion 1 against the
front seats, When repositioning:
- return the seat back to the upright
position,
- fold back the seat cushion,
- reposition the buckles before locking the front of the seat
cushion.
Take care not to trap the seat
belts.

Comfort92 -
01-10-2005
93Comfort-
01-10-2005
- position the seat belt under the belt holder 2,
- pull the controls 3 to unlock the
seat back 4,
- remove or lower the head restraints,
- tilt the seat back 4.
Always start with the seat, never
the seat back (risk of damage).
BENCH SEAT
To fold the bench seat:
- lift the front of the seat cushion 1,
- tilt the seat cushion 1 against the
front seats, When repositioning:
- return the seat back to the upright
position,
- fold back the seat cushion,
- reposition the buckles before locking the front of the seat
cushion.
Take care not to trap the seat
belts.

Comfort92 -
01-10-2005
93Comfort-
01-10-2005
TRANSPORTING LONG
OBJECTS
Front seat:
- Tilt the seat back towards the front using the control 5 (see corres-
ponding paragraph).
Removing the rear seat
- Tilt the seat cushion against the front seats.
- Squeeze the seat fasteners to re- lease them from their attachments.
- Remove the seat cushion.
Folding seat back
- Remove the head restraint for complete folding of the seat back.
- Push handle 5 towards the rear to
tilt the seat back.
Rear seat:
- Remove the seat cushion,
- Tilt the seat back.

Comfort92 -
01-10-2005
93Comfort-
01-10-2005
- position the seat belt under the belt holder 2,
- pull the controls 3 to unlock the
seat back 4,
- remove or lower the head restraints,
- tilt the seat back 4.
Always start with the seat, never
the seat back (risk of damage).
BENCH SEAT
To fold the bench seat:
- lift the front of the seat cushion 1,
- tilt the seat cushion 1 against the
front seats, When repositioning:
- return the seat back to the upright
position,
- fold back the seat cushion,
- reposition the buckles before locking the front of the seat
cushion.
Take care not to trap the seat
belts.

Comfort94 -
01-10-2005
95Comfort-
01-10-2005
"Forwards-facing"
When a "forwards-facing" child seat
is installed on the front passenger
seat , adjust the vehicle's seat to the
intermediate longitudinal position
with the seat back upright and leave
the passenger air bag armed**.
INSTALLING A CHILD SEAT
USING A THREE POINT SEAT
BELT
"Rearwards-facing"
When a "rearwards-facing" child seat
is installed on the front passenger
seat , it is essential that the passenger
air bag** is disarmed. Otherwise, the
child would risk being seriously
injured or killed if the air bag were
to inlate .
GENERAL POINTS RELATING
TO CHILD SEATS
Although one of PEUGEOT's main
criteria when designing your vehicle,
the safety of your children also
depends on you.
For maximum safety, please follow
these precautions:
- since 1992, and in accordance
with Directive 2000/3, all children
under the age of 12 must travel
in approved child seats* suited
to their weight , on seats itted with
a seat belt or ISOFIX mountings**.
- statistically, the safest seats in
your vehicle for the transpor-
tation of children are the rear
seats,
- a child weighing less than 9 kg must travel in the "rearwards-
facing" position both in the front
and in the rear.
PEUGEOT recommends that
children should travel in the rear
seats of your vehicle:
- "rearwards-facing" up to the age
of 2,
- "forwards-facing" over the age
of 2.
* According to current legislation in the country.
** According to model. Intermediate longitudinal
position

Comfort98 -
01-10-2005
99Comfort-
01-10-2005
These are two rings located between
the seat back and the seat cushion.
The ISOFIX child seats are itted
with two locks which are secured
easily on these rings."ISOFIX" MOUNTINGS
These seats* are itted with ISOFIX
mountings.
This ISOFIX mounting system
guarantees reliable, safe and fast
itting of the child seat in your
vehicle.
* According to version.
Saloon
206 SW 206 GTi 180