Peugeot 206 SW Dag 2006.5 Manual Online

Comfort82 -
AIR CONDITIONING
The air conditioning can only operate when the engine is running.
The air conditioning does not operate while the air flow adjustment control is in the "OFF" position.
To guarantee correct operation of your air conditioning system, we also recommend that you have it checked regularly.
1. Air conditioning On/Off
The air conditioning is designed to operate effectively in all seasons, with the windows closed. In summer, it permits lowering of the temperature and in winter, above 0 °C, it increases the effectiveness of the demisting.
2. Temperature adjustment
Turn the control from blue (cold) to red (hot) to adjust the temperature to suit your requirements.
Windscreen and side windows (de-icing/demisting).
Windscreen, side windows and footwells.
Press the switch, the indica-tor light comes on.
Footwells.
3. Air distribution adjustment
Centre and side vents.
These settings are recommended for cold climates.
This setting is recommended for hot climates.
The air distribution can be adjusted by placing the control in an interme-diate position, marked "-".

83Comfort-
4. Air flow adjustment
Turn the control from position 1to position 4 to obtain an air 44flow sufficient to ensure your comfort.
Intake of exterior air.
Air recirculation.
The recirculation of interior air prevents exterior odours and smoke entering the passenger compartment.
The intake of exterior air prevents and eliminates misting of the wind-screen and side windows.
Used simultaneously with the air con-ditioning, air recirculation improves air conditioning performance.
Used in a damp climate, air recirculation may result in misting of the windows.
Move the manual control 5 to the right to the "Interior air recirculation" position.
Move the manual control 5 to the left to the "Exterior air intake" position as soon as possible to prevent deterio-ration of the air quality.
5. Air intake/Air recirculation

Comfort84 -
AUTOMATIC AIR CONDITIONING
The air conditioning can only operate when the engine is running.
Automatic operation
2. Control by the AUTOprogramme
Press the "AUTO" button.
We recommend that you use this mode: it provides opti-mised automatic control of all of the functions, passenger com-partment temperature, air flow, air distribution and air recirculation, in accordance with the comfort value that you have chosen. This system is designed to operate effectively in all seasons, with the windows closed.
Note: for your comfort, the values set when the engine is switched off are retained on re-starting if the tempera-ture in the passenger compartment has not changed significantly; other-wise, operation resumes in automatic mode.
When the engine is cold, to prevent too great a distribution of cold air, the ventilation will only reach its optimum level gradually.
On entering the vehicle, if the interior temperature is much colder or warmer than is comfortable, there is no need to change the value displayed in order to reach the required level of comfort. The system eliminates the tempera-ture difference automatically and as quickly as possible.
Manual operation
If you wish, you can make a different choice from that offered by the sys-tem by changing a setting. The other functions will still be controlled auto-matically.
Pressing the AUTO button returns the system to completely automatic operation.
1. Temperature adjustment
The value indicated on the display corresponds to a level of comfort and not to a tem-perature in degrees Celsius or Fahrenheit.
Press the arrows 1 (up and down) to change this value. A setting around 21 enables a comfortable tempera-ture to be obtained.

85Comfort-
3. Air conditioning On/Off
Press this button to stop air cooling.
Thesymbol ECO is displayed.
Automatic operation of the air condi-tioning is resumed when the button is pressed again.
The symbol A/C is displayed.
4. Air distribution
Pressing this button several times in succession enables the air flow to be directed in turn towards:
- the windscreen (de-icing or demisting),- the windscreen and the footwells,- the footwells,- the centre and side vents and the foot-wells,- the centre and side vents.
5. Air flow
Press buttons "+" and "-" respectively to in-crease or decrease the air flow.
6. Air intake/Air recirculation
7. Switching the system off
The OFF button switches off all the functions of the system.
Temperature-related comfort and de-misting are no longer guaranteed but a slight flow of air is maintained.
Pressing the OFF, AUTO, or "visibility"button again reactivates the system with the values set before it was switched off.
Note: if you wish to cut off the flow of air completely, press the air intake button 7.
Press this button for recir-culation of the interior air. Recirculation, shown on the display, enables the passen-ger compartment to be insulated from exterior odours and smoke.
Avoid prolonged recirculation of inte-rior air (risk of condensation and de-terioration of the air quality).
Press the button again to resume auto-matic management of the intake of air.
Notes
To prevent condensation on the in-side of the vehicle in cold or wet weather, you are advised to avoid using the ECO mode.
To guarantee correct operation of your air conditioning system, we also recommend that you have it checked regularly.

Comfort86 -
Saloon and 206 SW

87Comfort-
206 GTi 180

Comfort88 -
FRONT SEATS
1 - Forwards-backwards adjustment
Lift the control and slide the seat towards the front or the rear.
2 - Head restraint height and angle adjustment (except 206 GTi 180)
To raise the restraint, pull it upwards.
The adjustment is correct when the upper edge of the head restraint is level with the top of the head.
The head restraint has a frame with notches, which prevent the head re-straint dropping down (this is a safety device in the event of an impact).
To lower the head restraint, it is necessary to push simultaneously:
- the button located on the left guide at the base of the head restraint, - the head restraint downwards.To remove the head restraint, press the lug.
The angle of the head restraint can also be adjusted.
4 - Seat height adjustment
Pull the handle upwards.
Remove your weight from the seat to raise, or press on the seat to lower.
5 - Seat back angle adjustment
Push one of the two handles towards the rear.
6 - Heated seats switch
Press the switch. The temperature is controlled automatically.
Press the switch again to stop operation.
Never drive with the head restraints removed; they must be in place and cor-rectly adjusted.
Rear head restraints
These have a high position for when they are in use and a low position for when they are stored. They are re-movable.
To lower the head restraints, press the lug.
To remove them, pull upwards as far as the stop, then press the release control.
3 - Access to rear seats(3 door), A or B accordingto version
A - Pull one of the two handles and push forwards to fold the seat back and move the seat forwards.
On repositioning, the seat returns to its initial position.
Noperson nor object must prevent the seat from returning to its initial position;returning to this positionis necessary for it to be locked.
It is impossible to access the rear seats if the front seat is in the reclining posi-tion.
B - Pull one of the two handles and push forwards to fold the seat back.
On repositioning, the seat back returns to its initial position.

Comfort88 -
FRONT SEATS
1 - Forwards-backwards adjustment
Lift the control and slide the seat towards the front or the rear.
2 - Head restraint height and angle adjustment (except 206 GTi 180)
To raise the restraint, pull it upwards.
The adjustment is correct when the upper edge of the head restraint is level with the top of the head.
The head restraint has a frame with notches, which prevent the head re-straint dropping down (this is a safety device in the event of an impact).
To lower the head restraint, it is necessary to push simultaneously:
- the button located on the left guide at the base of the head restraint, - the head restraint downwards.To remove the head restraint, press the lug.
The angle of the head restraint can also be adjusted.
4 - Seat height adjustment
Pull the handle upwards.
Remove your weight from the seat to raise, or press on the seat to lower.
5 - Seat back angle adjustment
Push one of the two handles towards the rear.
6 - Heated seats switch
Press the switch. The temperature is controlled automatically.
Press the switch again to stop operation.
Never drive with the head restraints removed; they must be in place and cor-rectly adjusted.
Rear head restraints
These have a high position for when they are in use and a low position for when they are stored. They are re-movable.
To lower the head restraints, press the lug.
To remove them, pull upwards as far as the stop, then press the release control.
3 - Access to rear seats(3 door), A or B accordingto version
A - Pull one of the two handles and push forwards to fold the seat back and move the seat forwards.
On repositioning, the seat returns to its initial position.
Noperson nor object must prevent the seat from returning to its initial position;returning to this positionis necessary for it to be locked.
It is impossible to access the rear seats if the front seat is in the reclining posi-tion.
B - Pull one of the two handles and push forwards to fold the seat back.
On repositioning, the seat back returns to its initial position.

89Comfort-
holder 2,- pull control 3 to unlock the seat back 4,- remove or lower the head restraint, - tilt the seat back 4.
Always start with the seat, never the seat back (risk of damage).
REAR SEATS
To fold the rear seats:
- lift the front of the seat cushion 1,- tilt the seat cushion 1 against the front seats,
When repositioning:
- return the seat back to the upright position,- fold back the seat cushion,- reposition the buckles before lock-ing the front of the seat cushion.
Take care not to trap the seat belts.

Comfort90 -
holder 2,- pull the controls 3 to unlock the seat back 4,- remove or lower the head restraints, - tilt the seat back 4.
Always start with the seat, never the seat back (risk of damage).
BENCH SEAT
To fold the bench seat:
- lift the front of the seat cushion 1,- tilt the seat cushion 1 against the front seats,
When repositioning:
- return the seat back to the upright position,- fold back the seat cushion,- reposition the buckles before lock-ing the front of the seat cushion.
Take care not to trap the seat belts.