display Peugeot 206 SW Dag 2008 Owner's Guide

Page 82 of 123

77
DRIVING
-
SPEED LIMITER
This speed limiter, of the new gener-
ation, has a display on the instrument
panel to indicate the programmed
speed.
It prevents exceeding of the vehicle
speed programmed by the driver.
When the programmed speed is
reached, pressing the accelerator
pedal no longer has any effect.
The limiter operates with a pro-
grammed speed of at least 18 mph
approx. (30 km/h); it remains active
regardless of any action on the brake
and clutch pedals.
The operating actions must be
carried out: - when stationary, with the
engine running,
or - with the vehicle moving. The indicator light on the in-
strument panel comes on at
the same time.
Instrument panel display
When the speed limiter function is
active, pressing this button displays
the distance recorders.
After a few seconds or when this but-
ton is pressed again, the display re-
turns to the speed limiter function.
Selecting the function
F
Place the dial 1 in the LIMIT
position. The limiter is not yet
active. By default, the display
indicates: Storing a speed
A speed can be stored without acti-
vating the limiter.
Press buttons
2 and 3 briely to de -
crease or increase by 1 mph (1 km/h).
An extended press decreases or in-
creases by 5 mph (5 km/h).
A maintained press decreases or in-
creases the programmed speed in
steps of 5 mph (5 km/h).
Activating / deactivating the
limiter
Pressing button 4 once activates the
limiter, pressing the button again de-
activates it.
When the limiter is active, the display
indicates (e.g. at 70 mph (110 km/h)):

Page 84 of 123

79
DRIVING
-
CRUISE CONTROL
This cruise control, of the new gene-
ration, has a display on the instru-
ment panel to indicate the memorised
reference speed.
It enables the vehicle to maintain a
steady speed programmed by the
driver.
In order for it to be memorised or ac-
tivated, the vehicle speed must be
greater than 24 mph approx. (40 km/h)
with at least fourth gear engaged for
vehicles itted with a manual gearbox.
On vehicles itted with an automatic
gearbox, the lever must be in po-
sition D at a speed greater than
24 mph approx. (40 km/h), or in
at least second gear in sequential
mode. The indicator light on the in-
strument panel comes on at
the same time.
Instrument panel display
When the cruise control function is
activated, pressing this button ena-
bles you to display the distance re-
corders.
After a few seconds or when this but-
ton is pressed again, the display re-
turns to the cruise control function.
Selecting the function
F
Place switch 1 in the CRUISE
position. The cruise control is
not yet active and no speed has
been memorised. The display
indicates in succession: First activation / memorising a
reference speed
As soon as you reach the chosen
speed, press button
2 or 3. This
memorises the speed and the display
indicates (e.g. at 70 mph (110 km/h)):
Note : It is possible to accelerate and
drive momentarily at a speed greater
than the memorised speed. The value
memorised lashes. When the accele-
rator pedal is released, the vehicle
returns to the memorised speed.
Cancelling the cruise control
If you wish to cancel the cruise control:
F Press button 4 or the brake or
clutch pedal.
The display indicates (e.g. at 70 mph
(110 km/h)):
The indicator light on the instrument
panel switches off.

Page 85 of 123

DRIVING
80 -
Reactivating the cruise control
After cancellation of the cruise con-
trol, press button 4. Your vehicle will
return to the last memorised speed.
The display indicates (e.g. at 70 mph
(110 km/h)):
It is also possible to reactivate the cruise
control by pressing button 2 or 3. The
memorised speed will then be the speed
at which the vehicle was travelling when
the cruise control was reactivated.
Changing the memorised
reference speed
To memorise a speed higher than the
previous one, there are two options:
Without using the accelerator:
F press button 3.
A brief press increases by 1 mph
(1 km/h).
An extended press increases by
5 mph (5 km/h).
A maintained press increases in
steps of 5 mph (5 km/h).
Using the accelerator:
F exceed the memorised speed
until the required speed is
reached,
F press button 2 or 3. To memorise a speed lower than the
previous one:
F
press button 2.
A brief press decreases by 1 mph
(1 km/h).
An extended press decreases by
5 mph (5 km/h).
A maintained press decreases in
steps of 5 mph (5 km/h).
Cancelling the memorised
reference speed
F When the vehicle becomes
stationary, after switching off the
ignition, the system no longer
memorisesw a speed.
Switching the function off
F Place dial 1 in position 0 to
switch the system off. Operating fault
In the event of a cruise control mal-
function, the memorised speed is
erased, the dashes lash for a few
seconds:
Contact a PEUGEOT dealer to have
the system checked.
When changing the memo-
rised reference speed by
means of a maintained press,
pay attention as the speed
can increase or decrease rapidly.
Do not use the cruise control on
slippery roads or in heavy trafic.
In the event of a steep slope, the
cruise control cannot prevent the
vehicle from exceeding the pro-
grammed speed.
In any event, the cruise control can-
not replace the need to observe the
speed limits, nor can it replace the
need for vigilance and responsibil-
ity on the part of the driver.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat and its ixings are positioned
correctly.
- never it one mat on top of another.
You are advised to keep your feet
near the pedals.

Page 87 of 123

SAFETY
82 -
TRACTION CONTROL (ASR)
AND DYNAMIC STABILITY
CONTROL (ESP)Disarming the ASR/ESP
systems
In exceptional conditions (starting a
vehicle which is bogged down, stuck
in snow, on soft ground), it may be
advisable to disarm the ASR and
ESP systems, so that the wheels can
move freely and regain grip.
F Press the "ESP OFF" switch,
located under the steering wheel
to the left. Operating check
The ASR/ESP systems
offer exceptional safety
in normal driving, but this
should not encourage the
driver to take extra risks or drive at
high speed.
The correct functioning of these
systems depends on observation
of the manufacturer's recommen-
dations regarding wheels (tyres
and rims), the braking components
and the electronic components
and the PEUGEOT assembly and
operation procedures.
After an impact, have these sys-
tems checked by a PEUGEOT
dealer.
Operation of the ASR and ESP
systems The switch lights up and the
warning light comes on, ac-
companied by a message
on the multifunction display :
the ASR and ESP systems are dis-
armed.
These are triggered again:
F automatically if the ignition is
switched off,
F manually by pressing the switch
again. When a malfunction of the
systems occurs, the switch
light lashes and the warning
light comes on.
Contact a PEUGEOT dealer to have
the systems checked.
The warning light lashes if
the ASR or ESP is activated.
Activation of the ASR and ESP
systems
When the ignition is on, the ASR and
ESP systems are always active.
These systems are linked and com-
plement the ABS.
The ASR system optimises drive to
prevent the wheels skidding, by act-
ing on the brakes of the drive wheels
and on the engine. It also allows the
directional stability of the vehicle to
be improved on acceleration.
If there is a variation between the tra-
jectory followed by the vehicle and
that required by the driver, the ESP
system automatically acts on the en-
gine and the brake of one or more
wheels, in order to put the vehicle
back on course, within the limits of
the laws of physics.

Page 88 of 123

83
SAFETY
-
AIR BAGS
The air bags have been designed to
maximise the safety of the occupants
in the event of serious collisions. They
work in conjunction with the force-lim-
iting seat belts. The electronic detec-
tors register and analyse any abrupt
deceleration of the vehicle in the im-
pact detection zones (see diagram):
if the triggering threshold is reached,
the air bags inlate instantly and pro -
tect the occupants of the vehicle. Immediately after the impact, the air
bags delate rapidly so that they do
not hinder the visibility of the occu-
pants nor their exit if necessary from
the vehicle.
The air bags are not deployed in the
case of minor impacts, rear impacts
or in certain roll-over conditions. The
seat belt is suficient to ensure maxi
-
mum protection in these situations.
The seriousness of a collision de-
pends on the nature of the obstacle
and the speed of the vehicle at the
moment of the collision.
Air bags only operate when the ig -
nition is switched on.
Note: the gas escaping from
the air bags can be a minor
irritant.
Impact detection zones
A. Front impact zone.
B. Side impact zone. If this warning light comes
on, accompanied by an au-
dible signal and a message
on the multifunction display,
contact a PEUGEOT dealer to have
the system checked. The air bags
may no longer be triggered in the
event of a serious impact Front air bag malfunction
FRONT AIR BAGS
These are folded in the centre of the
steering wheel for the driver and in
the fascia for the front passenger.
They are deployed simultaneously,
except in cases where the passen-
ger air bag is disarmed, in the event
of a serious front impact applied in
the impact zone
A in the longitudinal
centreline of the vehicle, on a hori-
zontal plane and from the front of the
vehicle towards the rear. The air bag
inlates between the front occupant of
the vehicle and the fascia to cushion
his forward movement. The air bags
therefore limit the risk of injury to the
head and chest.

Page 89 of 123

SAFETY
84 -
SIDE AIR BAGS AND
CURTAIN AIR BAGS
The side air bags are incorporated
into the front seat backs on the door
side.
The triggering of these air bags re-
quires a serious side impact applied
in the side impact zone B, perpen-
dicular to the longitudinal centreline
of the vehicle, on a horizontal plane
and from the outside of the vehicle
towards the inside. The side air bag
inlates between the front occupant
of the vehicle and the door trim pad.
It therefore limits the risk of injury to
the chest.
The rear side air bags afford the rear
passengers the same protection
which the front side air bags offer the
front passengers. If the passenger air bag is
disarmed, the warning light
on the instrument panel re-
mains on until the passenger
air bag is reactivated.
If this warning light comes
on, accompanied by an au-
dible signal and a message
on the multifunction display,
contact a PEUGEOT dealer to have
the system checked. The air bags
may no longer be triggered in the
event of a serious impact.
Disarming (check)
The curtain air bags are incorporated
in the headlining.
The curtain air bag inlates between
the front or rear occupant and the
windows. It therefore limits the risk of
head injuries. In the event of a minor
impact or bump on the side of the ve-
hicle or if the vehicle rolls over, the
air bag may not be triggered. The air
bag is not triggered in the event of a
front or rear collision.
Disarming the passenger
air bag
To ensure the safety of your child,
it is essential to disarm the pas -
senger air bag when you install
a "rear-facing" child seat on the
front passenger seat. Otherwise,
the child would risk being seri -
ously injured or killed if the air bag
were to inlate.
F With the ignition switched off ,
insert the key into the passenger
air bag disarming switch 1, turn
it to the "OFF" position, then
remove the key keeping the
switch in this position.
In the "OFF" position, the passen-
ger air bag will not be triggered in the
event of an impact.
As soon as the child seat is removed,
turn the air bag switch to the "ON"
position to re-activate the air bag and
thus ensure the safety of your pas-
senger in the event of an impact. Air bags malfunction

Page 91 of 123

SAFETY
84 -
SIDE AIR BAGS AND
CURTAIN AIR BAGS
The side air bags are incorporated
into the front seat backs on the door
side.
The triggering of these air bags re-
quires a serious side impact applied
in the side impact zone B, perpen-
dicular to the longitudinal centreline
of the vehicle, on a horizontal plane
and from the outside of the vehicle
towards the inside. The side air bag
inlates between the front occupant
of the vehicle and the door trim pad.
It therefore limits the risk of injury to
the chest.
The rear side air bags afford the rear
passengers the same protection
which the front side air bags offer the
front passengers. If the passenger air bag is
disarmed, the warning light
on the instrument panel re-
mains on until the passenger
air bag is reactivated.
If this warning light comes
on, accompanied by an au-
dible signal and a message
on the multifunction display,
contact a PEUGEOT dealer to have
the system checked. The air bags
may no longer be triggered in the
event of a serious impact.
Disarming (check)
The curtain air bags are incorporated
in the headlining.
The curtain air bag inlates between
the front or rear occupant and the
windows. It therefore limits the risk of
head injuries. In the event of a minor
impact or bump on the side of the ve-
hicle or if the vehicle rolls over, the
air bag may not be triggered. The air
bag is not triggered in the event of a
front or rear collision.
Disarming the passenger
air bag
To ensure the safety of your child,
it is essential to disarm the pas -
senger air bag when you install
a "rear-facing" child seat on the
front passenger seat. Otherwise,
the child would risk being seri -
ously injured or killed if the air bag
were to inlate.
F With the ignition switched off ,
insert the key into the passenger
air bag disarming switch 1, turn
it to the "OFF" position, then
remove the key keeping the
switch in this position.
In the "OFF" position, the passen-
ger air bag will not be triggered in the
event of an impact.
As soon as the child seat is removed,
turn the air bag switch to the "ON"
position to re-activate the air bag and
thus ensure the safety of your pas-
senger in the event of an impact. Air bags malfunction

Page 93 of 123

SAFETY
86 -
SEAT BELTS
Seat belt height adjustment:
- to lower: pull the control towards
you and slide it downwards,
- to raise: slide the control upwards. To fasten the seat belts
F
Pull the strap, then insert the
tongue into the buckle.
F Check that the seat belt is
fastened correctly by pulling the
strap.
To unfasten the seat belts
F Press the button on the buckle. Driver's seat belt not
fastened/unfastened warning

light
The warning light comes
on each time the ignition is
switched on.
It remains on until the driver fastens
his seat belt.
Above 12 mph (20 km/h), the warning
light lashes for two minutes accompa -
nied by an increasingly audible signal
and a message on the multifunction
display. Once these two minutes have
elapsed, the warning light remains lit
until the driver's seat belt is fastened.
Front seat belts with
pre-tensioner and force
limiter
Safety in the event of front impacts
has been improved by the introduc-
tion of seat belts with pre-tensioner
and force limiter for the front seats.
Depending on the seriousness of the
impact, the pre-tensioning system
instantly tightens the seat belts and
pulls them against the bodies of the
occupants. The pre-tensioning seat belts are ac-
tive when the ignition is on.
The force limiter eases the pressure
of the seat belt on the body of the oc-
cupant in the event of an accident.
Rear seat belts
The rear seats are itted with three
three-point inertia reel seat belts.

Page 108 of 123

101
PRACTICAL INFORMATION
-
Fuse N° Rating Functions
1 15A Heated seat - Alarm
4 20AMultifunction display - Boot lighting - Audio equipment - Stee ring wheel controls - Trailer
5 15A Automatic gearbox diagnostics
6 10A Coolant level - Automatic gearbox - Audio equipment - Stee ring wheel angle sensor (ESP)
7 15A Driving school accessory - Alarm itted as an accessory
9 30A Rear electric windows
10 40A Rear screen and mirror demisting
11 15A Rear windscreen wiper
12 30A Front electric windows - Sunroof
14 10AEngine fuse box - Air bags - Steering wheel controls - Rain sensor
15 15A Instrument panel - Multifunction display - Air condition ing - Audio equipment
16 30A Locking/unlocking controls for doors, bonnet and boot
20 10A Right-hand brake light
21 15A Left-hand brake light - 3rd brake light
22 20A Front courtesy light - Map reading light - Glove box lighting - Lighter
S1 Shunt PARC shunt

Page 111 of 123

PRACTICAL INFORMATION
104 -
BATTERY
To charge the battery using a bat-
tery charger:
- Disconnect the battery,
- Follow the instructions for use
given by the battery charger
manufacturer,
- Reconnect starting with the negative (-) terminal,
- Check that the terminals and connectors are clean. If they are
covered with sulphate (white or
greenish deposit), disconnect
them and clean them. - Wait for 2 minutes
after switching off
the ignition before
disconnecting the
battery.
- Never disconnect a terminal when the engine is running.
- Never charge a battery without irst disconnecting the
terminals.
- Close the windows and the roof before disconnecting the
battery.
- After every reconnection of the battery, switch on the
ignition and wait 1 minute
before starting to allow the
electronic systems to be
initialised. If slight dificulties
are experienced after this,
please consult a PEUGEOT
dealer.
It is advisable to disconnect the
battery if the vehicle is not to be
used for a period of more than
one month.
ECONOMY MODE
FUNCTION
After the engine has stopped, certain
functions (windscreen wiper, elec
-
tric windows, courtesy lights, audio
equipment, etc.) can only be used for
a combined duration of approximately
thirty minutes, to prevent discharging
the battery.
Once the thirty minutes are over, a
switching to economy mode mes-
sage appears on the multi-function
display and the active functions are
put on standby.
These functions are reactivated au-
tomatically next time the vehicle is
driven.
In order to resume the use of these
functions immediately, the engine
must be started and left to run for a
few minutes.
The time available to you will then
be double the duration for which the
engine is left running. However,
this period will always be between
ive and thirty minutes.
To start the vehicle from another
battery:
- Connect the red cable to the
positive (+) terminals of the
two batteries,
- Connect one end of the green or black cable to the negative (-)
terminal of the slave battery,
- Connect the other end of the green or black cable to an
earth point on the broken down
vehicle, as far as possible from
the battery (for example, right-
hand engine mounting),
- Operate the starter, let the engine run,
- Wait for the engine to return to idle, then disconnect the cables.
A lat battery prevents the
engine from starting.

Page:   < prev 1-10 11-20 21-30 31-40