high beam Peugeot 3008 Hybrid 4 2013 Owner's Manual

18
FA
M
SEEING CLEARLY

Li
ghting


Ring A
Lighting off.

Ring B Sidelamps.
Dipped / main beam headlamps.
Rear foglamp.
or
Front and rear foglamps. Automatic illumination of head-
lamps.
100, 101

Direction indicators

Raise or lower the lighting stalk passing
the point of resistance; the correspond-
ing direction indicators will fl ash for as
long as the stalk remains in this posi-
tion.

"Motorway" function
Press the lighting stalk up or down once,
without passing the point of resistance;
the corresponding direction indicators
will fl ash three times.
This function can be used at any speed,
but it is particularly useful when chang-
ing lane on high-speed roads.
134


Wipers


Stalk A: windscreen wipers

Switching on "AUTO"


)
Press the stalk down and release it.


Switching off "AUTO"


)
Push the stalk up and return it to po-
sition "0"
.
105

Ring B: rear wiper
Park.
Intermittent wipe.
Wash-wipe.
106

50
IN
S

Operation indicator lamps
If one of the following indicator lamps comes on, this confi rms that the corresponding system has come into operation.



Warning lamp



is on



Cause



Action / Observations






Left-hand
direction
indicato

r


fl ashing
with buzzer. The lighting stalk is pushed
down.




Right-hand
direction
indicator


fl ashing
with buzzer. The lighting stalk is pushed up.




Sidelamps


fi xed. The lighting stalk is in the
"Sidelamps" position.




Dipped beam
headlamps


fi xed. The lighting stalk is in the
"Dipped beam headlamps"
position.




Main beam
headlamps


fi xed.
The lighting stalk is pulled towards
you. Pull the stalk to return to dipped beam headlamps.
Ready


fi xed. The vehicle is ready to move off;
you can press the accelerator. It comes on once high voltage is established in
the vehicle.




Front
foglamps


fi xed. The front foglamps are switched
on. Turn the ring on the stalk rearwards twice to
switch off the front foglamps.




Rear
foglamps


fi xed. The rear foglamps are switched
on. Turn the ring on the stalk rearwards to switch off
the rear foglamps.

PRACTICAL INFORMATION
181







Changing dipped / main beam
headlamp bulbs


)
Remove the protective plastic cover
by pulling on the tab.

)
Disconnect the bulb connector.

)
Turn the bulb holder.

)
Pull out the bulb and change it.
To r efi t, carry out these operations in re-
verse order.
CHANGING A BULB










1.
Direction indicators
(PY21W-21W).


2.
Dipped / main beam headlamps
(H9-12V-65W).


3.
Sidelamps / daytime running
lamps (light emitting diodes -
LEDs).


4.
Foglamps (PS24-24W).



The headlamps are fi tted with
polycarbonate glass with a
protective coating:


)
do not clean them using a dry
or abrasive cloth, nor with a
detergent or solvent product,


)
use a sponge and soapy water or
a pH neutral product,

)
when using a high pressure wash-
er on persistent marks, do not
keep the lance directed towards
the lamps or their edges for too
long, so as not to damage their
protective coating and seals,

)
do not touch the bulb directly with
your fi ngers, use lint-free cloths.


Front lamps


Changing a bulb should only be
done after the headlamp has been
switched off for a few minutes (risk of
serious burns).
It is imperative to use only anti-ultra-
violet (UV) type bulbs in order not to
damage the headlamp.
Always replace a failed bulb with a
new bulb with the same type and
specifi cation.


Changing the light emitting
diode-LED lamps
For replacement, contact a PEUGEOT
dealer or qualifi ed workshop.

Before doing any work on your
vehicle, switch off the ignition
( Ready
lamp off) to avoid any
risk of injury resulting from automatic
operation of the engine.