bulb Peugeot 301 2015 Owner's Manual

.
.
Direction indicators 90
Hazard warning lamps
9
0
Horn
90
Under-inflation detection
9

1
Braking assistance systems

9
4
Trajectory control systems

9
5
Front seat belts

9
6
Airbags
9

9
Safety
Child seats 103
Deactivating the passenger's front airbag
1
06
ISOFIX mountings
1

12
Child lock

1
17
Child safety
Fuel tank 118
Misfuel prevention (Diesel)
1
19
Running out of fuel (Diesel)

1
21
Temporary puncture repair kit
1

22
Changing a wheel
1

28
Snow chains

1
35
Changing a bulb
1

36
Changing a fuse
1

42
Battery
1

47
Electrical energy economy mode
1

50
Changing a wiper blade
1

51
Towing the vehicle

1
52
Towing a trailer

1
54
Very cold climate screen(s)

1
56
Advice on care and maintenance
1

57
Accessories


157
Mats


159
Roof bars

1
60
Practical information
Petrol engines 1 71
Petrol weights
1
72
Diesel engine
1

73
Diesel weights

1
74
Dimensions


175
Identification markings
1

76
Technical data
Audio system / Bluetooth 177
Audio system
2
09
Audio equipment and telematics
Visual search
Alphabetical index
Checks
Bonnet
162
Petrol engines
1
63
Diesel engine
1

64
Checking levels

1
65
Checks
16

9
Contents

59
301_en_Chap04_amenagements_ed01-2014
Storage box
F Raise the boot carpet for access to the storage box.
This has areas for the storage of a box of spare
bulbs, a first aid kit, two warning triangles...
It also contains the vehicle tools, the temporary
puncture repair kit...
4
Fittings

136
301_en_Chap09_info-pratiques_ed01-2014
Changing a bulb
Front lamps
In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal sur face of the
glass of the headlamps and rear lamps
is normal; it disappears after the lamps
have been on for a few minutes.
The headlamps are fitted with
polycarbonate glass with a protective
coating:
F

d

o not clean them using a dr y
or abrasive cloth, nor with a
detergent or solvent product,
F

u

se a sponge and soapy water or a
pH neutral product,
F

w

hen using a high pressure washer
on persistent marks, do not keep
the lance directed towards the
lamps or their edges for too long,
so as not to damage their protective
coating and seals.
Changing a bulb should only be done
after the headlamp has been switched
off for several minutes (risk of serious
burns).
F

D

o not touch the bulb directly with
your fingers, use a lint-free cloth.
It is imperative to use only anti-
ultraviolet (UV) type bulbs to avoid
damaging the headlamp.
Always replace a failed bulb with a
new bulb with the same type and
specification. 1.
D

irection indicators (PY21W amber).
2.
M

ain beam headlamps (H1-55W).
3.
D

ipped beam headlamps (H7-55W).
4.
D

aytime running lamps

/ sidelamps
(W21/5W).


or
S

idelamps (W5W).
5.
F

ront foglamps (H11-55W).
Practical information

137
301_en_Chap09_info-pratiques_ed01-2014
Amber coloured bulbs, such as the
direction indicators, must be replaced
with bulbs of identical specifications
and colour.
When refitting, close the protective
cover carefully to preserve the sealing
of the headlamp.
Rapid flashing of the direction indicator
warning lamp (right or left) indicates the
failure of a bulb on that side.
Changing direction indicator
bulbs
F Turn the bulb holder an eighth of a turn
anti-clockwise and extract it.
F

R
emove the bulb and change it.
To reassemble, carry out these operations in
reverse order.
Changing main beam headlamp bulbs
F Remove the protective cover by pulling on the tab.
F

D
isconnect the bulb connector.
F

P
ush the spring to one side to release the
bulb.
F

R
emove the bulb and change it.
To refit, carry out these operations in reverse
o r d e r.
9
Practical information

138
301_en_Chap09_info-pratiques_ed01-2014
Changing dipped beam headlamp
bulbs
F Remove the protective cover by pulling the tab.
F

D
isconnect the bulb connector by lifting it
of f.
F

P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
Changing daytime running lamp /
s idelamp bulbs
F Pull the bulb holder pressing on the tabs on
both sides.
F

R
emove the bulb and change it.
To refit, carry out these operations in reverse
o r d e r.
Practical information

139
301_en_Chap09_info-pratiques_ed01-2014
Changing front foglamp bulbs
F Access to the front foglamp is through the aperture below the bumper.
I

f necessary, unscrew and completely
remove the cover.
F

T
urn the bulb holder a quarter turn anti-
clockwise and pull it out.
F

D
isconnect the bulb connector.
F

R
emove the bulb and change it.
To refit, carry out these operations in reverse
o r d e r. If you experience any difficulty
in replacing bulbs, contact your
PEUGEOT dealer or a qualified
workshop.
Changing direction indicator side
repeaters
F Insert a screwdriver towards the centre of
the repeater between the repeater and the
base on the body.
F

T
ilt the screwdriver to extract the repeater
and remove it.
F

D
isconnect the repeater connector.
F

R
eplace the module.
To refit, carry out these operations in reverse
o r d e r.
Contact a PEUGEOT dealer or
a qualified workshop to obtain a
replacement side repeater module.
9
Practical information

140
301_en_Chap09_info-pratiques_ed01-2014
Changing bulbs
These bulbs are changed from inside the boot:
F
o
pen the boot,
F

r
emove the access grille from the
corresponding side trim panel,
F

s
lacken and remove the nut,
F

d
isconnect the lamp unit connector,
F

u
nclip the lamp unit by lowering the tongue
and carefully extract it pulling in line
towards the outside, F

r
emove the four screws and lift off the bulb
h o l d e r,
F

t
urn the failed bulb a quarter of a turn and
change it.
To refit, carry out these operations in reverse
o r d e r.
Take care to engage the lamp unit in its guides,
while keeping it in line with the vehicle.
Tighten sufficiently to ensure sealing, but
without damaging the lamp.
1.
B

rake lamps

/ sidelamps (P21/5W).
2. D
irection indicators (PY21W amber).
3. R
eversing lamps (R10W).
4.
F

oglamp (P21W).
Rear lamps
Practical information

141
301_en_Chap09_info-pratiques_ed01-2014
Third brake lamp (5 W5W bulbs)Number plate lamps (W5W)
F Insert a thin screwdriver into one of the
transparent lens.
F

P
ush it outwards to unclip it and remove it.
F

R
emove the failed bulb and change it.
To reassemble, carry out these operations in
reverse order.
Ensure that the housing cover is
correctly positioned on its support
before clipping it into place.
To change these bulbs, it is necessary to
remove the housing from the rear shelf,
working from the rear seats:
F

p

ull the housing cover towards you and up
to disengage it, F
d
isconnect the lamp connector,
F
u
nclip the bulb holder by lifting the two lugs
and remove it,
F

r

eplace the failed bulb.
To reassemble, carry out these operations in
reverse order.
9
Practical information

158
301_en_Chap09_info-pratiques_ed01-2014
* To avoid any risk of jamming of the pedals:
-

e
nsure that the mat is positioned and
secured correctly,
-

n
ever fit one mat on top of another.
"Protection":
mats*, seat covers, alarm, front and rear mud
flaps, boot liner, boot carpet, side rubbing
strips, bumper protective strips, transparent
boot sill protector, shield under engine...
The fitting of electrical equipment or
accessories which are not recommended
by PEUGEOT may result in a failure of
your vehicle's electronic system and
excessive electrical consumption.
Contact a PEUGEOT dealer
for information on the range of
recommended equipment and
accessories.
Installation of radio
communication transmitters
Before installing any after-market radio
communication transmitter, you can
contact a PEUGEOT dealer for the
specification of transmitters which can
be fitted (frequency, maximum power,
aerial position, specific installation
requirements), in line with the Vehicle
Electromagnetic Compatibility
Directive (2004/104/EC).Depending on the legislation in force in
the country, certain safety equipment
may be compulsory: high visibility
safety vests, warning triangles,
breathalyzers, spare bulbs, spare fuses,
fire extinguisher, first aid kit, mud flaps
at the rear of the vehicle.
By visiting a PEUGEOT dealer, you can also
obtain products for cleaning and maintenance
(exterior and interior) - including ecological
products in the "TECHNATURE" range, topping
up products (screenwash...), touch-up pens
and paint aerosols for the exact colour of your
vehicle, refills (cartridge for the temporary
puncture repair kit...), ...
"Multimedia":
audio systems, portable satellite and semi-
integral navigation systems, fixed and
Bluetooth hands-free kit, universal solar
charger, speakers and wiring, 230 V socket,
rear multimedia bracket, telephone bracket...
Practical information

224
301_en_Chap13_recherche-visuelle_ed01-2014
Exterior
Remote control key 30 -33
- ope ning / closing
-
a

nti-theft protection
-


starting
-


battery
Boot
3

7-38
-
ope

ning / closing
-
em

ergency release
Temporary puncture repair kit
1

22-127
Wipers
87- 88
Changing a wiper blade
1

51
Changing bulbs
1

40-141
-
r

ear lamps
-
3
rd brake lamp
-
n
umber plate lamps
-


foglamp
Fuel tank, misfuel prevention
1

18-120
Running out of fuel (Diesel)

1
21
Accessories


157-158
ESP/ASR

95
Tyre pressures
1

76
Changing a wheel
1

28-134
-

tools
-

r

emoving / refitting
Snow chains

1

35
Under-inflation detection
9

1-93
Lighting controls
8

1-85
Daytime running lamps
8

5
Headlamp beam adjustment
8

6
Changing bulbs
1

36-139
-

f

ront lamps
-


foglamps
-
d

irection indicator repeaters
Towing


152-153
Very cold climate screen(s)

1

56
Door mirrors

4

3 - 44
Doors
3
0 -33, 36
-
ope

ning / closing
-

c

entral locking
-
s

econdary control
Alarm


34-35
Electric windows

3

9 Rear parking sensors
7

9-80
To w b a r

15 4
Visual search