Peugeot 307 2004.5 Workshop Manual

48
30-08-2004
49
30-08-2004
YOUR 307 IN DETAIL
Selecting the radio Automatic station searchRADIO
Notes on radio reception
Car radio/telephone receivers are
subject to phenomena which do not
affect domestic radio sets. Both MW/
LW and FM are subject to various
forms of interference. This is not a
relection on the quality of the equip-
ment, but is due to the nature of the
signals and the way in which they are
transmitted.
On MW/LW interference may be
noticed when passing under high
voltage power lines or bridges, or in
tunnels.
On FM, interference may be the re-
sult of the increasing distance from
the transmitter, delection of the sig-
nals by obstacles (mountains, hills,
buildings etc.) or of being in an area
which is not covered by a transmitter.Selecting a waveband
Briely press button
M or N to search
for the station immediately above or
below.
The search stops at the irst station
found.
If the TA trafic program is selected,
only the most powerful stations
broadcasting this type of program
are selected.
Searching for a station occurs irst
in "LO" sensitivity (selection of the
most powerful transmitters) for scan-
ning of the waveband, then in "DX"
sensitivity (selection of the weaker
and more distant transmitters).
To make a direct search in "DX"
sensitivity, briely press button M or
N twice.
Press
"SOURCE" several times.
Briely pressing but-
ton "BAND/AST" to
select the FM1, FM2,
FMast and AM wave-
bands.

48
30-08-2004
49
30-08-2004
Briely press button H or I
to increase or decrease the
frequency displayed.
By continuing to press
the button in the direction
selected, you will obtain
continuous scrolling of the
frequency.
Scrolling stops as soon as
the button is released.
Manual station search
Manual station storing
Select the station required.
Press one of the buttons
"1" to "6"
for more than two seconds.
Cutting off of the sound conirms that
the station has been stored in the
memory.
YOUR 307 IN DETAIL
Automatic storing of FM stations
in the memory (autostore)
Your audio/telephone automatically
stores the 6 stations with the strong-
est signal in FM. These stations are
stored in the FMast waveband.
If it is not possible to ind 6 stations,
the remaining memories are empty. Press the
"BAND/
AST" button for more
than two seconds.
Recalling stations stored in the
memory
For each waveband, briely press the
buttons "1" to "6" to recall the cor-
responding stored station.

50
30-08-2004
51
30-08-2004
YOUR 307 IN DETAIL
Regional following mode (REG)
When they are part of a network,
certain stations broadcast regional
programs in the various areas they
serve. With regional following mode
you can keep listening to the same
program.
To do this, press the "RDS" button
for more than two seconds to switch
the function on or off.
The multi-function screen will show:
- REG if the function is active,
- REG crossed out or greyed out
if the function is active but not
available.RDS
Using the RDS (Radio Data
System) function on FM
Radio Data System allows you to
continue listening to the same sta-
tion, whatever frequency it is using
for the region you are going through. Trafic information program
Briely press the "RDS"
button to switch the
function on or off.
T h e m u l t i - f u n c t i o n
screen will show:
- RDS if the function is active
- RDS crossed out or greyed out
if the function is active but not
available. Press the
"TA/PTY"
button to switch the
function on or off.
T h e m u l t i - f u n c t i o n
screen will show:
- TA if the function is selected
- TA crossed out or greyed out
if the function is selected but not
available.
Any trafic information lash will be
given priority, whatever source you
are listening to (radio, CD or CD
changer).
If you wish to interrupt the broadcast-
ing of a message, press the "TA/
PTY" button.
Note: the volume of the trafic
information is independent of the
volume of normal radio/telephone
listening.
You can adjust it by using the volume
button. The setting will be stored and
will be used when the next messages
are broadcast.
RDS station following
This display indicates the name of the
station selected. The audio/telephone
continuously searches for the trans-
mitter which transmits the same
program with the best reception. This
search may cause slight interference
with the transmission.

50
30-08-2004
51
30-08-2004
YOUR 307 IN DETAIL
PTY function
This allows you to listen to stations
broadcasting a speciic type of pro-
gram (news, culture, sport, rock
,
etc.)
When FM is selected, press button
"TA/PTY" for more than two seconds
to switch the function on or off.
To ind a PTY program:
Audio functions menu
Select the "Audio functions" menu
from the general menu to:
- "Activate/Deactivate RDS frequency following",
- "Activate/Deactivate REG regional mode",
- "Trafic information TMC". Contextual menu
- select the PTY button,
- turn button G to scroll down the dif-
ferent types of programs offered,
then conirm your choice,
- when the program of your choice is displayed press button M or N
to carry out an automatic search
(after an automatic search the PTY
function is switched off if no station
has been found).
In PTY mode, the different types of
program can be stored in the memory.
To do this, press the preselection
buttons "1" to "6" for more than
two seconds. To recall the type of
program stored in the memory, briely
press the corresponding button. EON system
This system connects stations which
are part of the same network. It ena-
bles the broadcast of trafic informa-
tion or a
PTY program, by a station
that is part of the same network as
the station to which you are listening.
The service is available when you
have selected the TA trafic informa-
tion program or the PTY function. By pressing knob
G, the contextual
menu allows you to access the fol-
lowing functions:
- "Enter a frequency",
- "List of stations" to access directly the 30 stations picked up locally,
- "Refresh list" to update this list,
- "Display Radio Text" to display information connected with the
station being listened to, if "RT" is
displayed permanently.

52
30-08-2004
53
30-08-2004
YOUR 307 IN DETAIL
Ejecting a discSelecting a track
By pressing knob G, the contextual
menu permits you to switch on or
switch off the shufle, play the start
of a track, track program and display
tracks played functions.
After inserting a disc, printed face
upwards, the CD drive starts auto-
matically.
If a disc has already been inserted,
press the
"SOURCE" button to se-
lect CD mode.
COMPACT DISC
Selecting CD mode
Press button M to select the follow-
ing track.
Press button N to return to the start
of the current track or to select the
previous track.
Do not use copied CDs as
these could damage your
player.
Insert circular compact
discs only.
Press button
B to
eject the disc from the
drive. Accelerated play
Press and hold button
M or N for
forwards or backwards accelerated
play.
Accelerated play stops as soon as
the button is released. Contextual menu

52
30-08-2004
53
30-08-2004
YOUR 307 IN DETAIL
Press button M to select the following
track.
Press button N to return to the start
of the current track or to select the
previous track. By pressing knob
G, the contextual
menu permits you to switch on or
switch off the shufle, playing the
start of a track or repeat a track and
display tracks played functions.
COMPACT DISC CHANGER
Selecting CD changer mode
Press the "SOURCE" button several
times.
Selecting a disc
Press one of the buttons "1" to "5"
on the audio/telephone to select the
appropriate disc.
Buttons H and I allow you to select
respectively the previous or following
disc in the changer. Selecting a track Contextual menu
Accelerated play
Press and hold button
M or N for
forwards or backwards accelerated
play.
Accelerated play stops as soon as
the button is released.

54
30-08-2004
55
30-08-2004
YOUR 307 IN DETAIL
TELEPHONE
This function is a GSM dual-band
telephone (900 and 1 800 MHz)
incorporated in the RT3 GPS audio/
telephone system.
It is a "hands free" telephone. This
function is provided by a microphone
located next to the front courtesy light,
the speakers, a steering column con-
trol and voice commands which allow
access to most of the functions (the
audio/telephone control panel buttons
allow access to all the functions).
Display of the principal "mobile"
type functions, as well as consulta-
tion of the directories, is provided by
the multi-function display.
This function is active , whatever
position the ignition key is in even af-
ter thirty minutes, when the message
"Economy mode active" appears
on the multi-function display. Using the menus
Press the
"MENU" button to dis-
play the general menu . Select the
telematics application, validate "Tele-
phone functions" to access the prin-
cipal telephone functions, then the
various menus, in order to reach the
one required.
This menu allows you to access the
following functions: Within each menu:
- Network: allows you to select the
network search mode and to see
the networks available.
- Duration of calls: allows you to
consult the duration recorder of
calls made and zero re-set.
- Security: allows you to use or
modify the PIN code and to erase
the list of calls and text messages
(SMS).
- Telephone options: allows you to
conigure the calls with entering of
my number, automatic answering
after X rings, speciication of ring
options and allows you to conigure
the call diversion number. Move around and se-
lect a function by turn-
ing the
G button then
validate by pressing
the button.
Cancel an operation us-
ing the "ESC" button.
Using the alphanumeric keypad
For a given button, to input a charac-
ter in the second or subsequent rows
press until you obtain the character
required.
Buttons Associated characters
[1] 1 or space
[2] 2 or A B C 2 or a b c 2
[3] 3 or D E F 3 or d e f 3
[4] 4 or G H I 4 or g h i 4
[5] 5 or J K L 5 or j k l 5
[6] 6 or M N O 6 or m n o 6
[7] 7 or P Q R S 7 or p q r s 7
[8] 8 or T U V 8 or t u v 8
[9] 9 or W X Y Z 9 or w x y z 9
[0] 0 or + (long press)
[#] # or validation
[*] * or erasing of last charac-
ter input (long press)

54
30-08-2004
55
30-08-2004
YOUR 307 IN DETAIL
Open lap L by pressing the
point of a pencil on the circu-
lar opening above the lap.
Insert your Micro-SIM card,
available from a mobile
telephone operator, as indicated in
the graphics, then close the lap.
Note: removal or insertion of the SIM
card must only be carried out after
the RT3 audio/telephone has been
switched off.
Installing the SIM card Inputting the PIN code
Input your PIN code using the al-
phanumeric keypad and validate by
pressing button G or button # to ac-
cess the network. Connection to the
network is validated by the appear-
ance of a symbol on the screen.
Warning: if you make three errors in
succession when inputting your PIN
code, your SIM card will be blocked.
To unblock it, you will need to input
the PUK code. The PUK code will be
supplied to you by the person sell-
ing your SIM card (input of the PUK
code allows for 10 errors in succes-
sion; after this the SIM card becomes
permanently unusable).
Note: the PIN code is required each
time the ignition is switched on, un-
less the PIN code has been stored
in the memory or protection by PIN
code is not activated on the SIM
card. Cancelling of PIN code request
In the menu
"Telephone functions"
select "Security" , then "Process
the PIN code" , then validate the
"Cancel" function.
Warning: in this case, do not lose
your SIM card. Losing it would mean
anyone who inds it would be able to
make unlimited calls.

56
30-08-2004
57
30-08-2004
Telephone function screens
Not in use
In use
YOUR 307 IN DETAIL
This screen indicates the presence
of voice messages or text mes-
sages (SMS) not listened to/read,
the cumulative time in use since the
last zero reset and the status of your
telephone.
This screen indicates the time
elapsed since the start of the con-
versation, as well as the number* or
name of the person to whom you are
speaking (if recorded in the directory)
and the status of your telephone.
*
If this option and service are available.
Making a call
Press button D to display the contex-
tual menu of the telephone.
Note: pressing the end 5 of the
steering column control for more
than 2 seconds calls up a contex-
tual menu limited to the "Directory",
"Calls list" and "Voice mail" func-
tions.
Entering a number
Select the function
"Enter number" then
enter the number of
the person you wish
to speak to using the
alphanumeric keypad.
Press button D to make
the call.
Making a call from a directory
Select the "Directory" function
to access all the iles containing a
telephone number or the "List of
calls" function to access the list
of the last twenty incoming (if the
number display option is active) or
outgoing calls.
Note: there are two directories, the
RT3 GPS audio/telephone directory
and the SIM card directory. To con-
sult the SIM directory, insert your
SIM card and enter your PIN code.
Receiving a call
When a ringing sounds
to let you know that
a call is waiting, you
can choose either to
accept it by pressing
button D or the end of
the steering wheel re-
mote control or not to
accept it by pressing the button Q or
by selecting and validating the "NO"
button on the "Answer?" screen.
If you accept the call, to end your
communication, press button Q.
If you do not accept the call, it is
transferred to your voice mail or to a
call diversion number.
You can activate or deactivate this
transfer by pressing button Q for
more than two seconds.

56
30-08-2004
57
30-08-2004
Text messages (SMS)
Accessing text messagesSending a text message "Duration of calls" menu
Select the "Duration of calls" func-
tion from the "Telephone functions" menu to consult the duration counters
for the calls made. The partial counter
totals the duration of the calls since
the last zero reset carried out using
the "Zero reset" button.
YOUR 307 IN DETAIL
When the buzzer sounds (if the SMS
text messages buzzer option is ac-
tive) and a superimposed screen
announces "Do you wish to read
the new text message (SMS)?" ,
you can choose to read the text mes-
sage received by selecting and vali-
dating "YES" or postpone reading
it by selecting and validating "NO",
by pressing the "ESC" button or by
waiting until the announcement dis-
appears. The message is read by the
voice synthesiser, if it is active.
Note: the old text messages stored
and the new text messages, the
reading of which you wished to
postpone, can be consulted. Press
the "MENU" button then validate
the telematic icon, select "Text
messages (SMS)" and validate the
function "Received text messages
reading" by pressing button G. Then
scroll through the list by turning the
button and press the button to select
the text message to be read. Note:
Before typing your irst text
message, check that your text mes-
sages (SMS) centre number is stored
correctly in the sub-menu "Server
centre N°" . If it is not, any text mes-
sages typed before this number is
entered will not be sent.
In the menu "Text messages
(SMS)" validate the function "Text
message writing" . Type your text
message using the alphanumeric
keypad and validate it using the
"OK" button to store it or validate the
"Send" button to send it. Validation
of the "Send" button enables you to
enter the number of your recipient or
select it from the directory or from the
list of calls and send the message. "Telephone options" menu
Select the
"Telephone options"
function from the "Telephone func-
tions" menu to access the functions:
•
"Conigure the calls" which permits
activation and deactivation of the
"show my number" and "automatic
answering after X rings" functions
฀•฀฀ "Ringing options" which permits
adjustment of the ringing volume
for voice calls, activation of the text
messages (SMS) receipt buzzer
and selection of a ring tone from
the ive offered
฀•฀฀ "Diversion number/voice mail"
which permits recording of the call
diversion number chosen by the
customer, otherwise the call will be
transferred to the voice mail.