Peugeot 307 2007.5 Owner's Guide

Page 31 of 212

INSTRUMENTS and CONTROLS
30
Distance remaining to be
travelled
(km or miles)
This is the distance remain-
ing to be travelled to the i nal destina-
tion. It is either calculated instantly by
the navigation system if guidance is
activated, or entered by the user.
If the distance is not entered, dashes
are displayed in place of the digits.
Average speed
(km/h or mph)
This is the average speed cal-
culated since the last trip com-
puter zero reset (ignition on).
Range
(km or miles)
This indicates the number
of miles (or kilometres)
which can still be travelled with the
fuel remaining in the tank in relation
to the average consumption over the
last few miles (kilometres) travelled. Current consumption
(l/100 km or km/l or mpg)
This is the average quantity
of fuel consumed over the
last few seconds.
Average consumption
(l/100 km or km/l or mpg)
This is the average quan-
tity of fuel consumed since
the last trip computer zero reset.
Distance travelled
(km or miles)
This indicates the dis-
tance travelled since the
last trip computer zero
reset.
A few definitions…
When the range falls below 20 miles
(30 km), dashes are displayed. After
i lling with at least 5 litres of fuel, the
range is recalculated and is displayed
when it exceeds 60 miles (100 km). If dashes are displayed con-
tinuously while driving in
place of the digits, contact a
PEUGEOT dealer. This function is only displayed
from 20 mph (30 km/h).
This i gure may increase fol-
lowing a change of driving
style or relief, resulting in a
signii cant change in the cur-
rent consumption.

Page 32 of 212

INSTRUMENTS and CONTROLS
31
Display C

 Press the "MENU" button to gain
access to the general menu.

 Press the arrows, then the "OK"
button to select the "Trip compu-
ter" menu.

 On the "Trip computer" menu,
select one of the following appli-
cations:
Warnings log
This summarises the active warning
messages, displaying them in suc-
cession on the multifunction display.
Status of the functions
This summarises the active or inac-
tive status of the functions present on
the vehicle.
Enter the distance to the
destination
This enables you to enter an approxi-
mate value for the distance to the i -
nal destination.
"TRIP COMPUTER" MENU
System which provides general infor-
mation concerning the status of certain
equipment with which your vehicle is
equipped, such as the warnings log,
the status of the functions...
"DIAGNOSTICS" MENU

 On the "Diagnostics" menu, se-
lect one of the following applica-
tions:
Colour display

 Press the "MENU" button to gain
access to the general menu.

 Turn the dial and press it to select
the "Diagnostics" menu.

Page 33 of 212

MULTIFUNCTION DISPLAYS
32
Presentation
This displays the following information:
- the time,
- the date,
- the outside temperature * (this l ashes if there is a risk of ice),
- the status of the accesses (doors, boot, ...),
- the warning messages (e.g.: "Emis- sion control system faulty") or infor-
mation messages (e.g.: "Auto lights
on"), displayed temporarily, can
be cleared by pressing the "ESC"
button,
- the trip computer (see corre- sponding section).
* With air conditioning only.
Parameter configuration
There are three display control buttons:
- "ESC" to abandon the operation
in progress,
- "MENU" to scroll through the
menus or sub-menus,
- "OK" to select the menu or sub-
menu required.
General menu
Press the "MENU" button to scroll
through the various menus of the
general menu:
- vehicle coni guration,
- options,
- display settings,
- languages,
- units.
Press the "OK" button to select the
menu required.
(RD4 AUDIO EQUIPMENT)

Page 34 of 212

MULTIFUNCTION DISPLAYS
33
Vehicle coni guration
Once the "Vehicle coni guration"
menu has been selected, you can
activate or deactivate the following
equipment:
- wiper linked with reverse gear (refer to the "Visibility" section),
- "follow-me-home" lighting (refer to the "Visibility" section),
- parking assistance (refer to the "Driving" section).
Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active,
not active, faulty). Languages
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).
Display settings
Once the "Display settings" menu
has been selected, you can gain ac-
cess to the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.
Units
Once the "Units" menu has been se-
lected, you can change the units of
the following parameters:
- temperature (°C or °F),
-
fuel consumption (l/100, mpg or km/l).
Once you have selected a setting,
press the "OK" button to change its
value.
Wait for approximately ten sec-
onds without any action to allow the
changed data to be recorded or press
the "ESC" button to cancel.
The display then returns to the nor-
mal display.
For safety reasons, coni gu-
ration of the multifunction
displays by the driver must
take place when stationary.

Page 35 of 212

MULTIFUNCTION DISPLAYS
34
* With air conditioning only.
General menu
Press the "MENU" button to gain ac-
cess to the general menu, then press
the "

" or "

" buttons to scroll
through the following items:
- radio-CD,
- vehicle coni guration,
- options,
- display settings,
- languages,
- units.
Press the "OK" button to select the
menu required.
Presentation
This displays the following informa-
tion, via the RD4 audio equipment
control keypad:
- the time,
- the date,
- the outside temperature * (this l ashes if there is a risk of ice),
- the audio source displays (radio, CD, ...),
- the status of the accesses (doors, boot, ...),
- the warning messages (e.g.: "Emission control system faulty")
or information messages (e.g.:
"Auto lights on"), displayed tem-
porarily, can be cleared by press-
ing the "ESC" button,
- the trip computer (see corre- sponding section). Radio-CD
With the RD4 audio equipment
switched on, once the "Radio-CD"
menu has been selected, you can
activate or deactivate the functions
linked with the use of the radio (RDS
following, REG mode), the CD or the
CD changer (introscan, random play,
CD repeat).
For further details concerning the
"Radio-CD" application, refer to the
RD4 part of the "Audio and Telemat-
ics" section. Vehicle coni guration
Once the "Vehicle coni guration"
menu has been selected, you can
activate or deactivate the following
equipment:
- rear wiper linked with reverse gear
(refer to the "Visibility" section),
- "follow-me-home" lighting (refer to the "Visibility" section),
- parking assistance (refer to the "Driving" section).
Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active,
not active, faulty).
MONOCHROME DISPLAY A

Page 36 of 212

MULTIFUNCTION DISPLAYS
35
Display settings
Once the "Display settings" menu
has been selected, you can gain ac-
cess to the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.
Languages
Once the "Languages" menu has
been selected, you can change
the language used by the display
(Français, Italiano, Nederlands, Por-
tugues, Portugues-Brasil, Deutsch,
English, Espanol).
Units
Once the "Units" menu has been se-
lected, you can change the units of
the following parameters:
- temperature (°C or °F),
-
fuel consumption (l/100, mpg or km/l).
Once you have selected a setting,
press the " 
" or " 
" buttons to
change its value.
Press the "
" or "" buttons to
move to the previous or next setting
respectively.
Press the "OK" button to record the
change and return to the normal dis-
play or press the
"ESC" button to
cancel.
For safety reasons, coni gu-
ration of the multifunction
displays by the driver must
take place when stationary.

Page 37 of 212

MULTIFUNCTION DISPLAYS
36
MONOCHROME DISPLAY C
(WITHOUT RD4 AUDIO EQUIPMENT)
Parameter configuration
There are three buttons and a navi-
gator to enable you to control the
screen:
- "MENU" to display the general
menu ,
- "MODE" to change the perma-
nent application (trip computer,
date, ...),
- "ESC" to abandon the operation
in progress,
- Rotation of the navigator: move-
ment on the display or changing
of a setting,
- Press on the navigator: coni r-
mation of the selection. Presentation
It displays the following information:
- the time,
- the date,
- the exterior temperature (this l ashes if there is a risk of ice),
- the accesses check (doors, boot, ...),
- the warning messages (e.g.: "Depol- lution system faulty") or information
messages (e.g.: "Automatic head-
lamp lighting activated"), displayed
temporarily, can be cleared by press-
ing the "ESC" button,
- the trip computer (see corre- sponding section),
General menu
Press the "MENU" button to access
the general menu:
- trip computer (see corresponding section),
- personalisation-coni guration.
Turn the navigator to select the menu
required, then coni rm by pressing
the navigator.
"Personalisation-
Configuration" menu
Once this menu has been selected, you
can access the following functions:
- dei ne the vehicle parameters,
- display coni guration,
- selection of the language.

Page 38 of 212

MULTIFUNCTION DISPLAYS
37
Dei ne the vehicle parameters
Once this menu has been selected,
you can activate or deactivate the fol-
lowing equipment:
- wiper linked with reverse gear (refer to the "Visibility" section),
- "follow-me-home" lighting and duration (refer to the "Visibility"
section),
- parking assistance (refer to the "Driving" section). Selection of the language
Once this menu has been selected,
you can change the language
used on the display (Deutsch,
English, Espanol, Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil).
Display coni guration
Once this menu has been selected,
you can access the following settings:
- brightness-video setting,
- date and time setting,
- selection of the units.
Once you have selected a setting,
press the navigator.
Turn the navigator to change its value.
Press the navigator to record the
change and move on to the next set-
ting or press the
"ESC" button to
cancel.
Example : "Duration of the "follow-
me-home" lighting"
For safety reasons, coni gu-
ration of the multifunction
displays by the driver must
take place when stationary.

Page 39 of 212

MULTIFUNCTION DISPLAYS
38
* With air conditioning only.
Controls
From the RD4 audio equipment con-
trol panel, you can:

 press the "MENU" button to gain
access to the general menu ,

 press the "
" or
"" buttons to
scroll through the items on the
screen,

 press the "MODE" button to
change the permanent application
(trip computer, audio source, ...),

 press the "
" or
"" buttons to
change a setting value,

 press the "OK" button to con-
i rm,
or

 press the "ESC" button to aban-
don the operation in progress.
Displays on the screen
This displays the following information:
- the time,
- the date,
- the outside temperature * (this l ashes if there is a risk of ice),
- the status of the accesses (doors, boot, ...),
- the audio sources (radio, CD, ...),
- the trip computer (refer to the cor- responding section).
Warning messages (e.g.: "Emission
control system faulty") or information
messages (e.g.: "Automatic switching
on of the headlamps activated") may
appear temporarily. These can be
cleared by pressing the "ESC" button.
General menu

 Press the "MENU" button to gain
access to the
general menu :
- audio functions,
- trip computer (refer to the cor- responding section),
- personalisation-coni guration,
- telephone (hands-free kit).

 Press the " " or " " buttons to
select the menu required, then
coni rm by pressing the "OK"
button.
MONOCHROME SCREEN C
"Audio functions" menu
With the RD4 audio equipment
switched on, once this menu has
been selected you can activate or de-
activate the functions linked with use
of the radio (RDS, REG, RadioText),
the CD or the CD changer (introscan,
shufl e, CD repeat).
For further details concerning the
"Audio functions" application, refer
to the RD4 part of the "Audio and
Telematics" section.
"Trip computer" menu
Once this menu has been selected,
you can consult information concern-
ing the status of the vehicle (warnings
log, status of the functions, ...).

Page 40 of 212

MULTIFUNCTION DISPLAYS
39
"Personalisation-
Configuration" menu
Once this menu has been selected,
you can gain access to the following
functions:
- dei ne the vehicle parameters,
- display coni guration,
- selection of the language.
Display configuration
Once this menu has been selected,
you can gain access to the following
settings:
- brightness-video setting,
- date and time setting,
- selection of the units.

Example: setting of the duration of
the "follow-me-home" lighting

 Press the " " or
"  "
buttons,
then the "OK" button to select the
menu required.

 Press the " "
or
"  " buttons,
then the
"OK" button to select
the "Lighting and signalling" line.

 Press the " " or
"  "
buttons
to set the value required (15, 30
or 60 seconds), then press the

"OK" button to coni rm.
For safety reasons, it is im-
perative that coni guration of
the multifunction displays by
the driver takes place when
stationary.
Define the vehicle parameters
Once this menu has been selected,
you can activate or deactivate the fol-
lowing equipment:
- wiper linked with reverse gear (refer to the "Visibility" section),
- "follow-me-home" lighting (refer to the "Visibility" section),
- parking assistance (refer to the "Driving" section).

 Press the " " or "  "
buttons,
then the
"OK" button to select the

"OK" box and coni rm or press
the "ESC" button to cancel.
Selection of the language
Once this menu has been selected,
you can change the language used
by the display (Deutsch, English,
Espanol, Français, Italiano, Nederlands,
Portugues, Portugues-Brasil).
"Telephone" menu
With the RD4 audio equipment
switched on, once this menu has been
selected you can coni gure your Blue-
tooth hands-free kit (matching), con-
sult the various telephone directories
(calls log, services, ...) and manage
your communications (pick up, hang
up, call waiting, secret mode, ...).
For further details concerning the
"Telephone" application, refer to the
RD4 part of the "Audio and Telemat-
ics" section.

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 61-70 71-80 ... 220 next >