language Peugeot 307 2007.5 Owner's Manual

Page 33 of 212

MULTIFUNCTION DISPLAYS
32
Presentation
This displays the following information:
- the time,
- the date,
- the outside temperature * (this l ashes if there is a risk of ice),
- the status of the accesses (doors, boot, ...),
- the warning messages (e.g.: "Emis- sion control system faulty") or infor-
mation messages (e.g.: "Auto lights
on"), displayed temporarily, can
be cleared by pressing the "ESC"
button,
- the trip computer (see corre- sponding section).
* With air conditioning only.
Parameter configuration
There are three display control buttons:
- "ESC" to abandon the operation
in progress,
- "MENU" to scroll through the
menus or sub-menus,
- "OK" to select the menu or sub-
menu required.
General menu
Press the "MENU" button to scroll
through the various menus of the
general menu:
- vehicle coni guration,
- options,
- display settings,
- languages,
- units.
Press the "OK" button to select the
menu required.
(RD4 AUDIO EQUIPMENT)

Page 34 of 212

MULTIFUNCTION DISPLAYS
33
Vehicle coni guration
Once the "Vehicle coni guration"
menu has been selected, you can
activate or deactivate the following
equipment:
- wiper linked with reverse gear (refer to the "Visibility" section),
- "follow-me-home" lighting (refer to the "Visibility" section),
- parking assistance (refer to the "Driving" section).
Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active,
not active, faulty). Languages
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).
Display settings
Once the "Display settings" menu
has been selected, you can gain ac-
cess to the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.
Units
Once the "Units" menu has been se-
lected, you can change the units of
the following parameters:
- temperature (°C or °F),
-
fuel consumption (l/100, mpg or km/l).
Once you have selected a setting,
press the "OK" button to change its
value.
Wait for approximately ten sec-
onds without any action to allow the
changed data to be recorded or press
the "ESC" button to cancel.
The display then returns to the nor-
mal display.
For safety reasons, coni gu-
ration of the multifunction
displays by the driver must
take place when stationary.

Page 35 of 212

MULTIFUNCTION DISPLAYS
34
* With air conditioning only.
General menu
Press the "MENU" button to gain ac-
cess to the general menu, then press
the "

" or "

" buttons to scroll
through the following items:
- radio-CD,
- vehicle coni guration,
- options,
- display settings,
- languages,
- units.
Press the "OK" button to select the
menu required.
Presentation
This displays the following informa-
tion, via the RD4 audio equipment
control keypad:
- the time,
- the date,
- the outside temperature * (this l ashes if there is a risk of ice),
- the audio source displays (radio, CD, ...),
- the status of the accesses (doors, boot, ...),
- the warning messages (e.g.: "Emission control system faulty")
or information messages (e.g.:
"Auto lights on"), displayed tem-
porarily, can be cleared by press-
ing the "ESC" button,
- the trip computer (see corre- sponding section). Radio-CD
With the RD4 audio equipment
switched on, once the "Radio-CD"
menu has been selected, you can
activate or deactivate the functions
linked with the use of the radio (RDS
following, REG mode), the CD or the
CD changer (introscan, random play,
CD repeat).
For further details concerning the
"Radio-CD" application, refer to the
RD4 part of the "Audio and Telemat-
ics" section. Vehicle coni guration
Once the "Vehicle coni guration"
menu has been selected, you can
activate or deactivate the following
equipment:
- rear wiper linked with reverse gear
(refer to the "Visibility" section),
- "follow-me-home" lighting (refer to the "Visibility" section),
- parking assistance (refer to the "Driving" section).
Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active,
not active, faulty).
MONOCHROME DISPLAY A

Page 36 of 212

MULTIFUNCTION DISPLAYS
35
Display settings
Once the "Display settings" menu
has been selected, you can gain ac-
cess to the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.
Languages
Once the "Languages" menu has
been selected, you can change
the language used by the display
(Français, Italiano, Nederlands, Por-
tugues, Portugues-Brasil, Deutsch,
English, Espanol).
Units
Once the "Units" menu has been se-
lected, you can change the units of
the following parameters:
- temperature (°C or °F),
-
fuel consumption (l/100, mpg or km/l).
Once you have selected a setting,
press the " 
" or " 
" buttons to
change its value.
Press the "
" or "" buttons to
move to the previous or next setting
respectively.
Press the "OK" button to record the
change and return to the normal dis-
play or press the
"ESC" button to
cancel.
For safety reasons, coni gu-
ration of the multifunction
displays by the driver must
take place when stationary.

Page 38 of 212

MULTIFUNCTION DISPLAYS
37
Dei ne the vehicle parameters
Once this menu has been selected,
you can activate or deactivate the fol-
lowing equipment:
- wiper linked with reverse gear (refer to the "Visibility" section),
- "follow-me-home" lighting and duration (refer to the "Visibility"
section),
- parking assistance (refer to the "Driving" section). Selection of the language
Once this menu has been selected,
you can change the language
used on the display (Deutsch,
English, Espanol, Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil).
Display coni guration
Once this menu has been selected,
you can access the following settings:
- brightness-video setting,
- date and time setting,
- selection of the units.
Once you have selected a setting,
press the navigator.
Turn the navigator to change its value.
Press the navigator to record the
change and move on to the next set-
ting or press the
"ESC" button to
cancel.
Example : "Duration of the "follow-
me-home" lighting"
For safety reasons, coni gu-
ration of the multifunction
displays by the driver must
take place when stationary.

Page 40 of 212

MULTIFUNCTION DISPLAYS
39
"Personalisation-
Configuration" menu
Once this menu has been selected,
you can gain access to the following
functions:
- dei ne the vehicle parameters,
- display coni guration,
- selection of the language.
Display configuration
Once this menu has been selected,
you can gain access to the following
settings:
- brightness-video setting,
- date and time setting,
- selection of the units.

Example: setting of the duration of
the "follow-me-home" lighting

 Press the " " or
"  "
buttons,
then the "OK" button to select the
menu required.

 Press the " "
or
"  " buttons,
then the
"OK" button to select
the "Lighting and signalling" line.

 Press the " " or
"  "
buttons
to set the value required (15, 30
or 60 seconds), then press the

"OK" button to coni rm.
For safety reasons, it is im-
perative that coni guration of
the multifunction displays by
the driver takes place when
stationary.
Define the vehicle parameters
Once this menu has been selected,
you can activate or deactivate the fol-
lowing equipment:
- wiper linked with reverse gear (refer to the "Visibility" section),
- "follow-me-home" lighting (refer to the "Visibility" section),
- parking assistance (refer to the "Driving" section).

 Press the " " or "  "
buttons,
then the
"OK" button to select the

"OK" box and coni rm or press
the "ESC" button to cancel.
Selection of the language
Once this menu has been selected,
you can change the language used
by the display (Deutsch, English,
Espanol, Français, Italiano, Nederlands,
Portugues, Portugues-Brasil).
"Telephone" menu
With the RD4 audio equipment
switched on, once this menu has been
selected you can coni gure your Blue-
tooth hands-free kit (matching), con-
sult the various telephone directories
(calls log, services, ...) and manage
your communications (pick up, hang
up, call waiting, secret mode, ...).
For further details concerning the
"Telephone" application, refer to the
RD4 part of the "Audio and Telemat-
ics" section.

Page 42 of 212

MULTIFUNCTION DISPLAYS
41
Selection of the language
Once the "Selection of the language"
menu has been selected, you gain
access to the following parameters:
- selection of the display, informa-tion and voice commands lan-
guage (Français, English, Italiano,
Portugues, Espanol, Deutsch,
Nederlands).
Display coni guration
Once the "Display coni guration"
menu has been selected, you gain
access to the following parameters:
- selection of the palette of colours available for the display,
- setting of the brightness and brilliance of the display,
- setting of the date and time (12 or 24 hour mode, adjustment of the
minutes on GPS),
-
selection of the units (temperature
in °Celsius or °Fahrenheit;
consumption in l/100 km or mpg
or km/l).
Sounds
Once the "Sounds" menu has been
selected, you gain access to the fol-
lowing parameters:
- setting of the voice commands,
- setting of the voice synthesiser (volume of the instructions
and other messages, male or
female),
- activation of the auxiliary input AUX. Dei ne the vehicle parameters
Once the "Dei ne the vehicle para-
meters" menu has been selected,
you can activate or deactivate certain
driving and comfort equipment:
- parking assistance (refer to the
"Driving" section),
- wiper linked with reverse gear (refer to the "Visibility" section),
- "follow-me-home" lighting and duration (refer to the "Visibility"
section).
"Configuration" menu

 Press the "MENU" button on the
RT4 GPS audio/telephone to gain
access to the
general menu .

 Turn the dial to select the

"Coni guration" menu, then
press it to coni rm.
Once this menu has been selected,
you can gain access to the following
functions:

Page 43 of 212

MULTIFUNCTION DISPLAYS
42
"Video" menu
You can connect video equipment
(camcorder, digital camera, DVD
player, ...) to the three audio/video
sockets, located in the glove box.

Videos can only be displayed
when stationary.
Once this menu has been selected,
you can select:
- "Activate video mode" to activate/ deactivate the video,
- "Video parameters" to set the display format, the brightness,
the contrast and the colours.

 Press the "MODE" or
"DARK"
button to disconnect the displaying
of the video.

 Press the "SOURCE" button
several times in succession to
select an audio source other than
that of the video.

 Select the line "Duration of the
"follow-me-home" lighting" then
coni rm.

Example: setting the duration of the
"follow-me-home" lighting

 Turn the dial to select the

"Lighting coni guration" menu,
then press it to coni rm.

 Select the duration then press the
dial.

 Turn the dial to set the value
required (15, 30 or 60 seconds),
then press the dial.

 Select the "OK" box, then
coni rm. The RT4 GPS audio/tele-
phone must reinitialise and
restart in order to change
the voice used by the voice
synthesiser (male or female)
or the language used by the
system.
For safety reasons, it is im-
perative that coni guration of
the multifunction displays by
the driver takes place when
stationary.

Page 172 of 212

157
02
GENERAL MENU
MAP: orientation, details,
display. AUDIO FUNCTIONS: radio,
CD, Jukebox, options.For maintenance of the
display, the use of a
soft, non-abrasive cloth
(spectacles cloth) is
recommended without any
additional product.
TELEMATIC: telephone,
directory, SMS.
CONFIGURATION: vehicle,
display, time, languages, voice,
auxiliary socket (AUX) parameters.
VIDEO: activation, parameters.
VEHICLE DIAGNOSTICS:
warnings log, status of the
functions.
NAVIGATION GUIDANCE:
GPS, stages, options. TRAFFIC INFORMATION: TMC
information, messages.

Page 198 of 212

183
1
2
3
3
3
3
2
3
3
4
4
1
3
2
3
1
2
3
3
2
2
2
1
2
2
2
1
1
1
MENU
4
3
2
2
3
3
6text message ring
call diversion to mailbox n°
delete calls log* The parameters vary according to vehicle (refer to the "Multifunction displays" chapter).
CONFIGURATION
VIDEO
VEHICLE DIAGNOSTICS Press the MENU button for more
than 2 seconds to gain access to the
next low chart.
VOICE COMMANDS LIST
Press the Music button several
times in succession to access the
following settings.
AUTO VOLUME CORRECTION
SELECT LANGUAGE
Each audio source (Radio, CD, MP3,
Jukebox, CD changer) has its own
separate settings.
DISPLAY CONFIGURATION
choose colour
adjust luminosity
set date and time
select units
SOUND voice commands setting
speech synthesis settingguidance instructions volume
other message volume
select female/male voice
activate/deactivate auxiliary source
DEFINE VEHICLE PARAMETERS* RESET TYRE PRESS. DETEC. SYS.*
ACTIVATE VIDEO MODE
VIDEO PARAMETERS
display formats
adjust luminosity
set colours
set contrasts
ALERT LOG
STATUS OF FUNCTIONS* AUDIO/TELEPHONE DIAGNOSTICS
GPS COVERAGE
UNIT BACKUP POWER
UNIT DESCRIPTION
NAVIGATION DEMONSTRATION
SERVICES CONFIGURATION
MUSICAL AMBIENCE
BASS
TREBLE
LOUDNESS CORRECTION
FR-RR BALANCE
LH-RH BALANCE
Flow chart version 7.0

Page:   1-10 11-20 next >