Peugeot 307 Break 2005 Owner's Guide

Instruments and controls24 -
01-06-2005
25Instruments and controls-
01-06-2005
Park
Automatic gearbox lever
positions indicatorIn the event of under-revving or over-
revving, the gear selected lashes for
a few seconds, then the actual gear
engaged is displayed.
Reverse
Neutral
Drive
Manual mode: 1st gear engaged
2nd gear engaged
3rd gear engaged
4th gear engaged This comes on when the
"SPORT"
programme on
the automatic gearbox is
selected.
This comes on when the
"SNOW" programme on
the automatic gearbox is
selected.
Automatic gearbox indicator
lights
"SNOW" indicator light Invalid value during
manual operation
This is displayed if a gear is not en-
gaged correctly (selector between
two positions).
"SPORT" indicator light

Instruments and controls24 -
01-06-2005
25Instruments and controls-
01-06-2005
INSTRUMENT PANEL
DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).
Note: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information relat-
ing to the cruise control or speed lim-
iter, when either of these is activated
(see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer's servicing schedule.
The point at which the next service
is due is calculated from the last
indicator zero reset (see correspond-
ing section). It is determined by two
parameters:
- the distance travelled,
- the time which has elapsed since the last service.
Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er's driving habits. Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display
indicates the number of miles [kilo-
metres] (rounded off) remaining until
the next service.
Example:
4,800 miles/km remain
before the next service. For ive sec-
onds after the ignition is switched on,
the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.

Instruments and controls26 -
01-06-2005
27Instruments and controls-
01-06-2005
Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
F Switch off the ignition,
F Press and hold the trip recorder
re-set button,
F Switch on the ignition.
The display begins a countdown.
When the display shows "= 0", re-
lease the button; the service symbol
disappears.
Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least ive
minutes, otherwise the zero re-set
will not be registered.
The service is overdue.
The service spanner lashes for
5 seconds after the ignition is
switched on.
Example:
the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the service spanner remains lit. The
display indicates the total and trip
distance.
Note: the service spanner may also
come on if more than two years have
elapsed since the last service.
The distance remaining to
the next service is less than
500 miles (1,000 km).
Example:
400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the indicator displays:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit .
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.

Instruments and controls26 -
01-06-2005
27Instruments and controls-
01-06-2005
Lighting rheostat
With the lights on, press the button to
vary the intensity of the lighting of the
instruments and controls. When the
lighting reaches the minimum (or maxi-
mum) setting, release the button then
press it again to increase (or reduce)
the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
Trip recorder zero reset
button
With the ignition on, press the button
until the zeros appear.
Pressing the button enables you to
alternate between the distance re-
corder and cruise control or speed
limiter displays, when either of these
is activated.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for a few
seconds, after the service information.Oil level correct
Oil level gauge fault Flashing of "OIL--"
indicates a malfunc-
tion of the engine oil
level gauge.
Contact a PEUGEOT dealer.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Flashing of "OIL",
linked with the serv-
ice warning light,
accompanied by an
audible signal and
a message on the
multifunction display, indicates a lack of
oil which could damage the engine.
If the lack of oil is conirmed by a
check using the dipstick, it is essen-
tial that the level is topped up.
Lack of oil Dipstick
There are 2 marks on the
dipstick:- never exceed level A,
- in position B, top up the level via the oil iller
cap, using the type of oil
suited to your engine.
A = max.
B = min.

Instruments and controls24 -
01-06-2005
25Instruments and controls-
01-06-2005
INSTRUMENT PANEL
DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).
Note: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information relat-
ing to the cruise control or speed lim-
iter, when either of these is activated
(see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer's servicing schedule.
The point at which the next service
is due is calculated from the last
indicator zero reset (see correspond-
ing section). It is determined by two
parameters:
- the distance travelled,
- the time which has elapsed since the last service.
Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er's driving habits. Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display
indicates the number of miles [kilo-
metres] (rounded off) remaining until
the next service.
Example:
4,800 miles/km remain
before the next service. For ive sec-
onds after the ignition is switched on,
the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.

Instruments and controls24 -
01-06-2005
25Instruments and controls-
01-06-2005
INSTRUMENT PANEL
DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).
Note: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information relat-
ing to the cruise control or speed lim-
iter, when either of these is activated
(see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer's servicing schedule.
The point at which the next service
is due is calculated from the last
indicator zero reset (see correspond-
ing section). It is determined by two
parameters:
- the distance travelled,
- the time which has elapsed since the last service.
Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er's driving habits. Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display
indicates the number of miles [kilo-
metres] (rounded off) remaining until
the next service.
Example:
4,800 miles/km remain
before the next service. For ive sec-
onds after the ignition is switched on,
the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.

Instruments and controls26 -
01-06-2005
27Instruments and controls-
01-06-2005
Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
F Switch off the ignition,
F Press and hold the trip recorder
re-set button,
F Switch on the ignition.
The display begins a countdown.
When the display shows "= 0", re-
lease the button; the service symbol
disappears.
Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least ive
minutes, otherwise the zero re-set
will not be registered.
The service is overdue.
The service spanner lashes for
5 seconds after the ignition is
switched on.
Example:
the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the service spanner remains lit. The
display indicates the total and trip
distance.
Note: the service spanner may also
come on if more than two years have
elapsed since the last service.
The distance remaining to
the next service is less than
500 miles (1,000 km).
Example:
400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the indicator displays:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit .
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.

Instruments and controls26 -
01-06-2005
27Instruments and controls-
01-06-2005
Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
F Switch off the ignition,
F Press and hold the trip recorder
re-set button,
F Switch on the ignition.
The display begins a countdown.
When the display shows "= 0", re-
lease the button; the service symbol
disappears.
Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least ive
minutes, otherwise the zero re-set
will not be registered.
The service is overdue.
The service spanner lashes for
5 seconds after the ignition is
switched on.
Example:
the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the service spanner remains lit. The
display indicates the total and trip
distance.
Note: the service spanner may also
come on if more than two years have
elapsed since the last service.
The distance remaining to
the next service is less than
500 miles (1,000 km).
Example:
400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the indicator displays:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit .
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.

Instruments and controls26 -
01-06-2005
27Instruments and controls-
01-06-2005
Lighting rheostat
With the lights on, press the button to
vary the intensity of the lighting of the
instruments and controls. When the
lighting reaches the minimum (or maxi-
mum) setting, release the button then
press it again to increase (or reduce)
the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
Trip recorder zero reset
button
With the ignition on, press the button
until the zeros appear.
Pressing the button enables you to
alternate between the distance re-
corder and cruise control or speed
limiter displays, when either of these
is activated.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for a few
seconds, after the service information.Oil level correct
Oil level gauge fault Flashing of "OIL--"
indicates a malfunc-
tion of the engine oil
level gauge.
Contact a PEUGEOT dealer.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Flashing of "OIL",
linked with the serv-
ice warning light,
accompanied by an
audible signal and
a message on the
multifunction display, indicates a lack of
oil which could damage the engine.
If the lack of oil is conirmed by a
check using the dipstick, it is essen-
tial that the level is topped up.
Lack of oil Dipstick
There are 2 marks on the
dipstick:- never exceed level A,
- in position B, top up the level via the oil iller
cap, using the type of oil
suited to your engine.
A = max.
B = min.

Instruments and controls28 -
01-06-2005
29Instruments and controls-
01-06-2005
TRIP COMPUTER Monochrome screens A
- the range,
- the current consumption,
- the distance travelled,
- the average consumption,
- the average speed.
Each time the button on the end of
the wiper stalk is pressed, the vari-
ous items of trip computer data are
displayed in succession, depending
on the multifunction display: Zero reset
Press the stalk for more than two
seconds.
Monochrome screens C
- the
"vehicle" tab with:
• the range, the current consump- tion and the distance still to be
driven,
- tab "1" (route 1) with:
• the average speed, the average consumption and the distance
driven calculated over route "1",
- tab "2" (route 2) with the same fea-
tures for a second route.
Zero re-set
When the required route is displayed,
press the button for more than two
seconds.