engine Peugeot 307 Break Dag 2003.5 Owner's Manual

29-09-2003





 C
The menu BB&
1 BB
provides access to the following functions:
– changing of the route calculation criteria,
– voice synthesis adjustment of guidance messages,
– description of the information relating to the navigation CD-Rom,
– management of the addresses stored in the directory.
&
1
The last criterion used is displayed. Select a criterion from the list, then validate by pressing the dial. When the criterion of your choice has been selected, select the
090
function then confirm by pressing thedial.
> $
)&
&
%)&  & Select the type of voice 0'&0or
0.&'&0 , after inserting the configu-
ration CD-Rom.
Adjust the volume of the voice synthesis by turning the dial, then validate bypressing the dial.
&/ the volume can also be adjusted
during a message, using the audio/ telephone button or the steeringwheel control. $&'&
.
)&
&% This function enables you to rename
an address stored in the directory. Select the description corresponding to the stored address to be changed. Select the
0&'&0 function, then
confirm by pressing the dial.Select the 090function, then confirm
by pressing the dial to record the changes made.
11$D& '$
$&
 "Stop guidance" During guidance, select this function then validate.
 "Resume guidance" In the absence of guidance, select this function then validate to activateguidance to the last destination programmed.
&/ after re-starting the engine, a
screen appears enabling you to resume guidance activated before
the ignition was switched off.
*
&

29-09-2003
sport programme
snow programme
 ark to  
 the vehicle or



 ,
with the handbrake on or off.
 everse to 
 (select this function with the vehicle
stationary, engine at idle).  eutral to



 and to 
, with the
handbrake on. 
if function is engaged inadvertently while
driving, allow the engine to return to idle before engaging function to accelerate.
 rive for  in automatic mode.
 anual for  in manual mode.



!"# $
%

&&
With the engine running, to move off from position :
 
















'


(
 select function ,  or , then
gradually release the pressureon the brake pedal; the vehicle
moves off immediately.
You can also move off from position :
 release the handbrake, with yourfoot on the brake,
 select function ,  or , then
gradually release the pressureon the brake pedal; the vehicle
moves off immediately.
)# * When the engine is at idle, brakes not applied, if function ,  or is select-
ed the vehicle moves even withoutthe accelerator being pressed. For this reason, 



+ ,

-
-




+ (
.


- .
When maintenance operations needto be carried out with the engine run-ning, apply the handbrake and selectposition .
/01!
" " 0
"!/
#"#" 0
*!#23














 




 










 








 



   
*


 +

  Move the lever in the gate to select a function. Once the function is selected, the corresponding indicator light appears on
the instrument panel display.

29-09-2003
#-
+

 Automatic changing of the &-


:
 select function in the gate.
The gearbox always selects the most suitable gear according to the follow-ing parameters:
– the style of driving,
– the road profile,
– the vehicle load. The gearbox is then operating in auto-adaptive mode, without anyaction on your part.
)# * Never select function when the
vehicle is moving. Never select functions or unless
the vehicle is stationary.Never change between functions to optimise braking on a slippery surface. 
For immediate maximum accelera-
tion without touching the gear lever,press the accelerator pedal down as
far as it will go (kickdown). The gear-box will automatically change downor maintain the gear selected untilmaximum engine speed is reached. When braking, the gearbox will auto- matically change down in order to
provide efficient engine braking. If you take your foot off the accelera-
tor suddenly, the gearbox will notchange to a higher gear for reasons
of safety.




.

 In addition to the auto-adaptive pro- gramme, there are two special pro-grammes. The programme is displayed on the instrument panel screen.


  Press button once the vehicle
has been started and function 
selected.
The gearbox automatically favours sporty driving and more dynamicacceleration.
.

 This programme improves starting
and drive when traction is poor.  Press button once the vehicle
has been started and function 
selected.
The gearbox adapts to driving on slippery roads. 
you can return to the auto-
adaptive programme at any time.  Press button or again to
switch off the programme you are in. 
-


 Manual changing of the
&-


:
 select function in the gate,
 push the lever to the 4sign to
change to a higher gear,
 pull the lever to the 5sign to
change to a lower gear.
You can change from position 
(driving in automatic mode) to posi- tion (driving in manual mode) at
any time.  It is only possible to change from one gear to another if the vehicle speedand engine speed permit. If they donot, the vehicle will operate tem-porarily in automatic mode. When the vehicle is stationary or
moving very slowly, the gearboxautomatically selects gear %.
Programme (sport) and (snow)
do not operate in manual mode.



!"# $ %%

29-09-2003
"#0" 
0"$ 9#:
#
# 0
"#2 $ "
0"$ 9!: These systems are linked and com-
plement the ABS.
The ASR system optimises drive to prevent the wheels skidding, by act-ing on the brakes of the drive wheelsand on the engine. It also allows thedirectional stability of the vehicle tobe improved on acceleration. If there is a variation between the tra- jectory followed by the vehicle and
that required by the driver, the ESPsystem automatically acts on theengine and the brake of one or morewheels, in order to put the vehicleback on course.

++
When a malfunction of thesystems occurs, the switchlight flashes and the warninglight comes on, accompa-nied by an audible signal
and the message /!>#

&-+/ on the multifunction
display.
Contact a PEUGEOT dealer to have the system checked.



!"# $
%?



#>!
6

In exceptional conditions (starting a vehicle which is bogged down, stuck
in snow, on soft ground, ...), it may
be advisable to disarm the ASR and
ESP systems, so that the wheels canmove freely and regain grip. 
Press the /! ;;/ switch,
located on the central section of the fascia.
The switch lights up and thewarning light comes on: the
ASR and ESP systems aredisarmed.
"






  automatically if the ignition is
switched off,
 automatically above 30 mph (50 km/h),
 manually by pressing the switchagain.


&

#


!
6


The warning light flashes if
the ASR or ESP is activated.

 !"#
 























 











 
 



 





$






%

 &




 


 



'()









 
"







 




'()



29-09-2003
 +

&-+ Place switch %in the 0 ! posi-
tion. The cruise control is not yet active and no speed has been
memorised. The display indicates:
.+

&-+
&&  Place switch %in position or
$  " to switch the system off.
#+
>




 As soon as you reach the chosen speed, press button 8or . This
memorises the speed, which will
be maintained automatically. Thedisplay indicates (e.g. at 80 mph(130 km/h)): 
It is possible to accelerate and
drive momentarily at a speed greater
than the memorised speed. Thevalue memorised flashes. When theaccelerator pedal is released, thevehicle will return to the memorisedspeed.
0 !
0"$>!! $  "!A
0-

+
&-+

this enables
the vehicle to maintain a steady speed
programmed by the driver, regardlessof the road characteristics and withoutthe driver having to touch the accelera-tor or brake pedals. In order for it to be memorised, the vehicle speed must be greater than25 mph (40 km/h) with at least fourthgear engaged (second gear for theautomatic gearbox), .


- .
* During the year, according to engine.



!"# $
%B
0
+ 




 If you wish to cancel the memorised speed: Press button ?or the brake or clutch
pedal. The display indicates (e.g. at 80 mph (130 kmh)):

the speed memorised is can-
celled automatically if the vehiclespeed is less than 25 mph (40 kmh),or if the manual gearbox is in a gearlower than fourth (second gear forthe automatic gearbox) or if the ESPis activated.
+





 After cancellation, press button ?.
Your vehicle will return to the last
memorised speed. The display indi-cates (e.g. at 80 mph (130 km/h)):

29-09-2003



!"# $
%C
 +

&-+ 
Place switch %in the $  " posi-
tion. The limiter is not yet active. By default the display indicates:
.+

&-+
&&  Place switch %in position or
0 ! or switch off the ignition to
switch the system off. The last speed programmed remains in the
memory.






A speed can be memorised without
activation of the limiter.
A brief press on buttons 8and 
decreases or increases by 1 mph
(1 km/h). An extended press decreas-es or increases the memorised speed
progressively.
#+
>
+

&
 
Pressing button ?activates the lim-
iter, pressing this button again deac-tivates it. When the limiter is active, the display indicates (e.g. at 80 mph (130 km/h)):
0 !
0"$>!! $  "!A
$
&-+

this prevents the
vehicle speed exceeding the speed programmed by the driver (minimumspeed of 20 mph (30 km/h)).
"



-


+

-
.


-=
* During the year, according to engine.
!'+



 Pressing the accelerator to exceed the programmed speed will have no
effect unless the pedal is pressedfirmly (passing the 
&


,

+: .
The limiter is deactivated temporarily and
displays (e.g. at 80 mph (130 km/h)):
To re-activate the limiter, release the accelerator to slow down to a speedbelow the programmed speed. 
sometimes (on a steep
descent), the limiter may not prevent the vehicle from exceeding the pro-grammed speed, this speed flashes.


++ In the event of a limiter malfunction, the memorised speed is erased, thedashes flash for a few seconds:
Contact a PEUGEOT dealer to have the system checked.